Brinks 2057-120-1 Operating instructions

Brinks
Brand
Brinks
Model
2057-120-1
Category
Garage Door Opener
Type
Operating instructions

Brinks 2057-120-1 is a high-security deadbolt lock designed to provide maximum protection for your home or business. It features a 1-inch deadbolt that is made of hardened steel and is virtually impossible to cut or pry open. The lock also has a built-in alarm that will sound if the deadbolt is tampered with or if the lock is forced open.

The Brinks 2057-120-1 is easy to install and can be used on both residential and commercial doors. It is also weather-resistant and can be used in both indoor and outdoor applications.

Here are some of the features and benefits of the Brinks 2057-120-1:

Brinks 2057-120-1 is a high-security deadbolt lock designed to provide maximum protection for your home or business. It features a 1-inch deadbolt that is made of hardened steel and is virtually impossible to cut or pry open. The lock also has a built-in alarm that will sound if the deadbolt is tampered with or if the lock is forced open.

The Brinks 2057-120-1 is easy to install and can be used on both residential and commercial doors. It is also weather-resistant and can be used in both indoor and outdoor applications.

Here are some of the features and benefits of the Brinks 2057-120-1:

Bore 7/8" dia. hole
1/2" deep above
and below
center point.
Bore 7/8" dia. hole
1/2" deep above
and below
center point.
Converting from an existing standard doorknob to a handleset.
a
) Remove existing hardware.
b) Determine the side of the template that allows you to place it on the OUTSIDE surface of the
d
oor. Fold enclosed template along indicated line and place template against door edge.
c
) Align Hole A on template with existing doorknob hole.
d) Mark Hole C and drill a 5/16” (7.9mm) diameter hole.
Be sure to confirm correct hole location for your particular handleset series number.
e) Confirm all other holes are properly prepared and proceed to the hardware installation
i
nstructions.
F
or new installation into a non-bored door.
a) Determine the side of the template that allows you to place it on the OUTSIDE surface of the
door. Fold enclosed template along indicated line and position template against door edge at
desired height. (Handleset is typically 38” (965 mm) from the ground with deadbolt located
at least 5-1/2” (140mm) above handleset).
b
) Determine door thickness and desired backset and mark centers for Holes A through E.
c) Drill designated diameters for Holes A through E.
a) Insert Deadbolt latch into Hole E and Handleset latch into Hole B.
b) Outline each latch faceplate onto door edge.
c) Remove latches and chisel outlined area approximately 1/8” (3.2mm) deep or until each
faceplate is flush.
d) Reinsert latches into the respective holes, mark and drill pilot holes for faceplate screws.
MARKING THE HOLE LOCATIONS
LATCH RECESS PREPARATION
For Deadbolt strike
a) With door closed, use a nail or marker through Hole E to mark center location of strike plate onto door jamb.
b) Using the 4 hole reinforcement plate as a template, outline plate onto door jamb.
c) Drill two 7/8” (22mm) holes 1/2” (13mm) deep above and below center location mark, barely overlapping each other.
d) Chisel out outlined area approximately 1/8” (3.2mm) deep or until reinforcement plate and strike plate cover is flush.
e) Reposition reinforcement plate, mark and drill pilot holes for screws.
STRIKE PLATE PREPARATION
For Handleset Strike Plate
a) With door closed, use a nail or marker through Hole B to mark center location of strike plate onto door jamb.
b) Using the curved strike plate as a template, outline plate onto door jamb.
c) Drill two 7/8” (22mm) holes 1/2” (13mm) deep above and below center location mark, barely overlapping each other.
d) Chisel out outlined area approximately 1/16” (1.6mm) deep or until strike plate is flush.
e) Reposition strike plate, mark and drill pilot holes for screws.
DOOR PREPARATION INSTRUCTION SHEET
B
A
E
B
E
D
C
Confirm that all holes have been properly prepared and proceed to the hardware installation instructions.
Hampton Products International Corp.
50 Icon
Foothill Ranch, CA
92610-3000
www.hamptonproducts.com
1-800-562-5625
Made in China
© 2007 Hampton Products International Corp.
999-00124 REVA 3/07
  • Page 1 1

Brinks 2057-120-1 Operating instructions

Brinks
Brand
Brinks
Model
2057-120-1
Category
Garage Door Opener
Type
Operating instructions

Brinks 2057-120-1 is a high-security deadbolt lock designed to provide maximum protection for your home or business. It features a 1-inch deadbolt that is made of hardened steel and is virtually impossible to cut or pry open. The lock also has a built-in alarm that will sound if the deadbolt is tampered with or if the lock is forced open.

The Brinks 2057-120-1 is easy to install and can be used on both residential and commercial doors. It is also weather-resistant and can be used in both indoor and outdoor applications.

Here are some of the features and benefits of the Brinks 2057-120-1:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents