(English)
DM-SH0001-00
TL-SHCFIN
Dealer's Manual
CF Insole Heat Molding Kit
2
CONTENTS
IMPORTANT NOTICE .............................................................................................. 3
TO ENSURE SAFETY ............................................................................................... 4
LIST OF ITEMS CONTAINED IN THIS KIT ............................................................... 6
HEAT MOLDING THE INSOLES .............................................................................. 8
Preparation for heat molding .....................................................................................................................8
Heat molding procedure .............................................................................................................................8
Adjustment of insole size ..........................................................................................................................10
3
IMPORTANT NOTICE
IMPORTANT NOTICE
•
This dealer’s manual is intended primarily for use by professional bicycle mechanics.
Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer’s manuals.
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local
bicycle dealer for their assistance.
•
Make sure to read all instruction manuals included with the product.
•
Do not disassemble or modify the product other than as stated in the information contained in this dealer’s manual.
•
All dealer’s manuals and instruction manuals can be viewed on-line on our website (http://si.shimano.com).
•
Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.
For safety, be sure to read this dealer’s manual thoroughly before use, and follow it for correct use.
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
4
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
•
Be sure to follow the instructions provided in the manuals when installing and using the product.
•
For applying heat, make sure to use the oven for Shimano custom-fit shoes. Do not use any other means for applying heat.
For instructions on using the oven for Shimano custom-fit shoes, refer to the "Dealer Instruction for heat molding of Custom-fit Shimano Shoes",
included with the oven.
•
The operator must wear protective gloves when heat molding procedure is being carried out in order to avoid possible burns.
•
After reading the dealer's manual thoroughly, keep it in a safe place for later reference.
Be sure to also inform users of the following:
•
This procedure must only be done by trained retail employees who have read this document.
NOTE
Be sure to also inform users of the following:
•
Products are not guaranteed against natural wear and deterioration from normal use and aging.
Using the product:
•
Only use items included in the Shimano CF Insole (Custom Fit insole) heat molding kit and Shimano custom-fit kit.
Only items included in the Shimano CF Insole heat molding kit and Shimano custom-fit kit have been tested for heat molding and approved by
Shimano.
The actual product may differ from the illustration because this manual is intended mainly to explain the procedures for using
the product.
LIST OF ITEMS CONTAINED IN THIS KIT
6
LIST OF ITEMS CONTAINED IN THIS KIT
LIST OF ITEMS CONTAINED IN THIS KIT
ITEM ITEM
Footbed × 1 Heel guide plate (ETLSHCFINSMHP) × 2
Sponge, EVA sheet (ETLSHCFINSMFB) × 1
HEAT MOLDING THE INSOLES
HEAT MOLDING THE INSOLES
Preparation for heat molding
8
To be continued on next page
HEAT MOLDING THE INSOLES
Preparation for heat molding
To be prepared by consumer:
•
Shimano insoles for heat molding (including arch pads)
•
Cycling socks
To be prepared by the operator:
•
Oven for Shimano custom-fit shoes
NOTE
Pre-heat the oven for approximately 10
minutes.
The temperature inside the oven will reach
around 100°C (210°F).
Heat molding procedure
1
Prepare the CF insoles and pre-heat the oven.
2
Place the EVA sheet on the footbed.
Place the sponge on top and secure the
heel guide plate in the appropriate
position with reference to the below
table.
Position of
footbed guide
Insole size Appropriate shoe size
36 36 - 37.5 36 37 37.5 -
38 38 - 39.5 38 38.5 39 39.5
40 40 - 41.5 40 40.5 41 41.5
42 42 - 43.5 42 42.5 43 43.5
44 44 - 45.5 44 44.5 45 45.5
46 46 - 47.5 46 46.5 47 47.5
48 48 - 50 48 49 50 -
HEAT MOLDING THE INSOLES
Heat molding procedure
9
To be continued on next page
3
Once the oven is hot, place the insole,
with the yellow arch pad attached, into
the oven faced upward, and heat for 1
minute 30 seconds.
NOTE
•
To avoid overheating, shrinkage, or
damage to the material, make sure to take
the insole out after 1 minute 30 seconds.
•
Be careful when placing the insole into the
oven as the inside of the oven will be
extremely hot. Make sure that no contact is
made with the sides of the oven as there is
a risk of damage to the material.
•
This product is pre-fitted with yellow arch
pads. The pads must be left on during
heating and molding. If arch support is felt
to be excessive after heat molding, remove
the arch pad, and if support is insufficient,
attach the red arch pad instead.
If heat molding is to be re-performed, it
should be done after attaching the yellow
arch pads.
•
When performing heat molding, the toe
arch pad should not be attached. If
re-performing heat molding, make sure to
remove the toe arch pad.
4
Place the heated up insole on the
footbed.
Align your heel with the heel guide plate
and align the toe end by aligning the
center of the insole with the center of
the footbed.
HEAT MOLDING THE INSOLES
Adjustment of insole size
10
5
Wearing cycling socks, align your heel
with the heel guide plate and stand on
the insole resting your body weight on it.
Rest the foot that is not on the footbed
on a block etc., to ensure that both feet
are at the same elevation.
If molding both feet at the same time,
prepare two of these kits.
6
Remain still for 2 minutes in this standing position.
After 2 minutes, once the inner sole has cooled down, remove your foot from it and adjust
the size of the insole.
NOTE
Heat molding of the inner soles can be done
up to two times within the warranty period.
After two times the heat molding can still be
repeated, however the molding might slowly
become less effective.
Adjustment of insole size
To adjust the size of the insole, place the
insole included with the shoe on to the
CF insole, align the heels, and trim the
toe end until the insoles are of the same
size.
This completes the heat molding procedure for the inner soles.
Please note: specifications are subject to change for improvement without notice. (English)
© Jul. 2016 by Shimano Inc. HTR
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
SMANIA B09CMDWQNS User manual
-
Case Logic NGC-1BLACK Datasheet
-
Sharper Image Heated Insoles User manual
-
Moticon OpenGo Instructions Manual
-
ThermaCELL Heated Insoles Operating instructions
-
-
-
Crivit CEB 2000 A1 Operating Instructions Manual
-
-
Rhinotuff RHINOTUFFE Specification
