Strong SM-PROJ-L-WH Owner's manual

Brand: Strong

Model: SM-PROJ-L-WH

Category: Projector mounts

Type: Owner's manual

This manual is also suitable for

SM-PROJ-L-BLK

Strong™ Universal Projector Mount for Projectors up to 50 Lbs. (Black)

For Mounting on a Concrete Ceiling (Fig. 4)

a. Pre-drill four holes into concrete using 3/8” Masonry bit.

Insert Concrete Anchors and tap in with hammer, if necessary.

  WARNING:WheninstallingCeilingPlateoncinderblock,rstverifythereisaminimumof1-3/8”

of concrete thickness to be used for the Concrete Wall Anchors. Do not drill into mortar joints!

  Besuretomountinasolidpartoftheblock,generally1”minimumfromthesideoftheblock.

  CinderblockmustmeetASTMC-90specications.Itissuggestedthatastandardelectricdrillonslow

  settingisusedtodrilltheholeinsteadofahammerdrilltoavoidbreakingoutthebackofthehole

  whenenteringavoidorcavity.Concretemustbe2000psidensityminimum.Lighterdensityconcrete

may not hold concrete anchor.

Make sure that the supporting surface will safely

support the combined load of the equipment and

all attached hardware and components.

 b.InsertfourLagScrewsintotheConcreteAnchors

through the Extended Ceiling Plate.

WARNING: Tighten screws so that the Extended

  CeilingPlateisrmlyattached,butdonotover-tighten.

  Over-tighteningcandamagethescrews,greatly

reducing their holding strength.

c. Insert Extension Pole (ULListedSM-FIXPOLEseries,not

  included)intoExtendedCeilingPlate.Lockpolein

place with two M5 set screws.

 d.OnbottomofExtensionPole,threadonLow-Prole

Ceiling Plate, making sure the arrow (on bottom)

faces the screen when installed. Tighten Security Screw

  (pre-installed)tolockLow-ProleCeilingPlateontoExtension

Pole to set in place.

Step 3: Attach the Projector Mount Body (Fig.5)

a. Slightly loosen all screws so arms easy rotate and extend to

match the holes on the projector. Making sure the arrow

on bottom points toward the projector lens, attach the

Projector Mount Body onto projector using supplied M3,

  M4,M5orM6SocketScrewsandM2orM4AllenKey.

b. Depending on the surface of the projector, lowering

  theAngleBracketsontheendofthearmstogetaush

  mountingmaybenecessary(Fig6).

 NOTE:Positioncenterofgravityofprojectortothemiddle

of the mount, if possible.

Step 5: Assemble Projector Mount Body

   withLow-ProleCeilingPlate

a. While holding projector, slide top of Projector

  MountBodyintotheLow-ProleCeiling

  Plateasindicated(Fig.7).

 b.UsingeitheraPhilipsHeadScrewdriveror

  ngers,pushinandturnlockscrew(attached

  toLow-ProleCeilingPlate)tosecure.

 c. Using4mmAllenkey,install10-32SocketSecurity

  Screwintooppositesideasindicated(Fig.8).

Adjustments

To change the tilt or roll of the mount for centering the picture,

useAllenkeyandrstloosenscrewsonProjectorMountBody.

Tilt the projector into the desired position and re-tighten the screws.

Lifetime

Fig4

Fig5

Fig6

Fig7

Fig8

Lifetime Limited Warranty

All Strong™ products have a Lifetime Limited Warranty. This warranty includes parts and labor repairs on all

components found to be defective in material or workmanship under normal conditions of use. This warranty

shall notapply to products which have been abused, modied or disassembled. Products to be repaired under

this warranty must be returned to SnapAV or a designated service center with prior notication and an

assigned return authorization number (RA).

For Techincal Support : 1.866.838.5052

10-32SecurityScrew

LockScrew

INSTALLATION INSTRUCTIONS

Step1:UseCeilingPlatetoMarkMountingHoleLocations(Low-ProleorExtension)

a. Theuseofastudnderishighlyrecommended.WhenmountingtheLow-ProleCeilingPlate,

  makesurearrowonbottomoftheLow-ProleCeilingPlatefacestowardthescreen.

Step2:MounttheCeilingPlate

Low-Prole Ceiling Plate

For Mounting on a Wood Joist (Fig. 1)

 a.Pre-drilltwoholesintojoistusinga3/16”drillbit.

Be sure to drill into the center of the joists.

 b.InserttwoLagScrewsintoholesthroughthe

  Low-ProleCeilingPlateandtightendown.

 WARNING:TightenscrewssothattheLow-Prole

CeilingPlateisrmlyattached,butdonotover-

 tighten.Over-tighteningcandamagethescrews,

greatly reducing their holding strength.

For Mounting on a Concrete Ceiling (Fig. 2)

a. Pre-drill two holes into concrete using 3/8” Masonry bit. Insert Concrete Anchors and

tap in with hammer, if necessary.

  WARNING:WheninstallingCeilingPlateoncinderblock,rstverifythereisaminimumof1-3/8”

of concrete thickness to be used for the Concrete Wall Anchors. Do not drill into mortar joints!

  Besuretomountinasolidpartoftheblock,generally1”minimumfromthesideoftheblock.

  CinderblockmustmeetASTMC-90specications.Itissuggestedthatastandardelectricdrillonslow

  settingisusedtodrilltheholeinsteadofahammerdrilltoavoidbreakingoutthebackofthe

  holewhenenteringavoidorcavity.

  Concretemustbe2000psidensity

  minimum.Lighterdensityconcrete

may not hold concrete anchor.

Make sure that the supporting surface

will safely support the combined load

of the equipment and all attached

hardware and components.

 b.InserttwoLagScrewsintotheConcrete

  AnchorsthroughtheLowProleCeilingPlate.

WARNING:TightenscrewssothattheLow-Prole

  CeilingPlateisrmlyattached,butdonotover-

  tighten.Over-tighteningcandamagethescrews,

greatly reducing their holding strength.

Extension Ceiling Plate

For Mounting on a Wood Joist (Fig. 3)

a. Use Extension Ceiling Plate to mark two hole locations.

  Pre-drilltwoholesintojoistusinga3/16”drillbit.Besure

to drill into the center of the joists.

 b.InserttwoLagScrewsintoholesthroughtheExtension

Ceiling Plate and tighten down.

  WARNING:TightenscrewssothattheLow-ProleCeiling

  Plateisrmlyattached,butdonotover-tighten.Over-

tightening can damage the screws, greatly reducing their

holding strength.

 c. ThreadExtensionPole(ULListedSM-FIXPOLEseries,notincluded)

  intoExtendedCeilingPlate.LockpoleinplacewithtwoM5setscrews.

 d.OnbottomofExtensionPole,threadonLow-ProleCeiling

Plate, making sure the arrow (on bottom) faces the screen

when installed. Tighten Security Screw (pre-installed) to lock

  Low-ProleCeilingPlateontoExtensionPoletosetinplace.

#14x2.5”

LagScrew(x4)

#14x2.5”

LagScrew(x4)

ExtensionCeilingPlate(x1) ExtensionPlateCover(x1)

M3x8 Socket

Screw, security (x4)

Low-ProleCeiling

Plate(x1)

Projector Mount

Body(x1)

M4x10Socket

Screw, security (x4)

M5x10Socket

Screw, security (x4)

M6x10Socket

Screw, security (x4)

10-32X10Socket

Screw,security(x1)

10x50Concrete

Anchor (x4)

4mm (ID) Washer

(x4)

4mm (ID) Washer

(x4)

M5x5 Set Screw,

security/non-security

(x2/2)

2mmAllenWrench,

security(x1)

2mmAllenWrench,

security(x1)

4mm Allen Wrench,

security(x1)

HARDWARE KIT

SPECIFICATIONS

 •Maximumload:50lbs(22.68kg).

 •Tiltrange:+/-25º

 •Roll:+/-6º

TOOLS REQUIRED

 •PhilipsHeadScrewDriver

 •PowerDrill

 •3/16”(5mm)DrillBit

 •3/8”(10mm)MasonryBit

 •StudFinder

 •10mmor3/8”Socket

Head Wrench

WARNINGS

 •Wehighlyrecommendthisproductbeinstalled

  byaqualiedprofessional.

 •Donotbegininstallationuntilyouhave 

thoroughly read and understand these instructions.

 •Thismountsupportsprojectorswithamaximumload

  of50lbs(22.68kg).

 •Ensuretheceilingwillsafelysupportfourtimesthe

combined weight of the mount and projector.

 •Undernocircumstancesshouldthisproduct

be mounted to metal studs.

 •Themanufacturerdoesnotacceptresponsibility

for incorrect installation.

MAINPACKAGECONTENTS

EXTENSIONPLATECONTENTS

Fig1

Fig2

Fig3

CAUTION:

This mount is intended for use only with

themaximumweightof50lbs(22.68kg).

Strong SM-PROJ-L-WH Owner's manual

Brand: Strong

Model: SM-PROJ-L-WH

Category: Projector mounts

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Strong SM-PROJ-L-WH Owner's manual

This manual is also suitable for

Strong SM-PROJ-L-WH Owner's manual

Related papers

Other documents