Pelco C1555M-F User manual

Brand: Pelco

Model: C1555M-F

Category: Digital Video Recorders (DVR)

Type: User manual

This manual is also suitable for

C1572M

ADDENDUM

Pelco Worldwide Headquarters

• 3500 Pelco Way • Clovis, California 93612 USA •

www.pelco.com

USA & Canada

•Tel: 800/289-9100 • Fax: 800/289-9150

International

•Tel: 1-559/292-1981 • Fax: 1-559/348-1120

Addendum No.

C1573M

Date

February 1, 2006

Manuals Affected

C1572M, C1555M-F, C1566M-C

Manual Update

The front and rear mounting rails and the mounting brackets are no longer supplied with the CM9700-CC1.

Disregard the CM9700-CC1 mounting information in the above referenced manuals.

To mount the CM9700-CC1 into a standard 19-inch EIA rack follow these instructions:

1. Insert the CM9700-CC1 into the rack.

2. Tighten the CM9700-CC1 to the rack using the four supplied Phillips screws with washers.

Figure 1.

Mounting the CM9700-CC1

(4) SCREWS,

10-32 X 0.750-INCH

PHILLIPS, PAN HEAD

WITH WASHERS

CM9700-CC1

RACK

INSTALLATION/OPERATION

System 9770

C1555M-F (10/05)

C1555M-F (10/05) 3

Contents

Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

List of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Video Input/Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Installing Video Input Cards (CM9770-VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Installing Monitor Output Cards (CM9770-VMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Performing a Basic LED Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Installing Rear Panel BNC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Video Input/Output Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

The Power Supply Module (CM9700-MPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Install a Backup Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Remove a Backup Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

How to Replace the Fuse in a Power Supply Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

How to Turn Off the Audible Power Supply Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

System Device Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

RS-422 COM Port (“Sercom”) Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

System Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Initialize the CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Verify System Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Initialize Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Display the CM9770-MXB Software Version Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Display a Blue Raster Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Monitor Color Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Programming Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Getting Help Using CM9700-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Operating Your System 9770 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

System Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

How to Expand Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Installing Additional Matrix Bays—Sideframing and Downframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

How to Install or Replace a CM9700-SER Card in the CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Video Input Card (CM9770-VCC) Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Monitor Output Card (CM9770-VMC) Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Connecting Satellite Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Programming Satellite Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

How to Install Video Patch Panels (CM9700-VPP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Mounting the CM9770-MXB in an Open Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

DOS Environment and Command Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

The Boot Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

AUTOEXEC.BAT and the Boot Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

DOS Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64

4 C1555M-F (10/05)

List of Illustrations

1 CM9770-MXB Mounting Bafﬂe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

2 Mounting the CM9770-MXB on Top of the Mounting Bafﬂe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

3 Mounting the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

4 Video Input Card (CM9770-VCC) Locations: Slots 1-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

5 Monitor Output Card (CM9770-VMC) Locations: Slots 9-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

6 Insert a Rear Panel Video BNC Card (CM9770-RPC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

7 Remove a Rear Panel Video BNC Card (CM9770-RPC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

8 CM9770-RPC Termination Jumpers—Right Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

9 CM9770-RPC Termination Jumpers—Left Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

10 Looping Video Out from the CM9770-MXB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

11 CM9770-MXB Matrix Bay—16 Monitor Output Connections for Each VMC Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

12 Sample CM9770 System with 256 Cameras and 32 Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

13 Sample System Using Sideframing from Bay to Bay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

14 Sample Sideframing System Using an Output Bay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

15 Sample Single-Node System with Downframing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

16 Sample Networked System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

17 How to Install or Remove a Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

18 How to Replace a Power Supply Fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

19 Power Supply Alarm Speaker Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

20 Connect the CM9760-KBD to the CM9700-CC1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

21 CM9700-CC1 Device Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

22 CM9700-MGR PC Pin-Out Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

23 Sample CM9770-MXB to CM9700-CC1 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

24 Sample CM9770-MXB and CM9700-CC1 Connections in a Networked System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

25 CC1 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

26 System 9770 Color Bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

27 Getting Started Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

28 Sample Wizard Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

29 CM9700-MGR Main Window - Properties Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

30 CM9700-MGR Main Window - Help Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

31 Downframing with DFC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

32 Looping Video Out in a Downframed Conﬁguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43

33 DFC Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

34 DFC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

35 CM9770-DFL Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

36 Removing the CC1 Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

37 SER Card Jumper Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

38 How to Install a CM9700-SER Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

39 CM9770-VCC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

40 CM9770-VMC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

41 Sample Networked System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

42 Sample Satellite System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

43 Add a Satellite Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

44 CM9700-VPP Horizontal Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

45 CM9700-VPP Vertical Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

46 Mounting the CM9770-MXB in an Open Rack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

C1555M-F (10/05) 5

List of Tables

A LEDs Illuminated During a Basic Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

B Data Connections—Single Node Systems Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

C Data Connections—Networked System Without a Hot Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

D Data Connections—Single Node, Hot-Switched System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

E Data Connections—Networked, Hot-Switched System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

F SER Card Jumper Assignments for a CM9700-CC1 System Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

G SER Card Jumper Assignments for a CM9700-NW1 Network Interface Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

H Video Input Card (CM9770-VCC) LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

I Monitor Output Card (CM9770-VMC) LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

J Monitor Output Card DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

K DOS Command Reference Directory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

L CC1 Hardware Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

M CC1 System Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

N Monitor Output Card DIP Switch 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

6 C1555M-F (10/05)

Description

The System 9770 is a full-featured video matrix switching control system that allows users to view and control up to 2,048 cameras and

512 monitors on a single node.

The System 9770 has the following basic components:

• CM9700-CC1—This is the system CPU; connect matrix bays, keyboards, PTZ camera control lines, and peripheral devices to the CC1.

• CM9770-MXB—This is the video matrix (switching) bay with video input/output modules; connect cameras, monitors, VCRs, and other

video input and output devices to the MXB.

• CM9760-KBD—This is the system keyboard, providing operator control of the System 9770.

• CM9700-MGR installed on an external PC—This is the system management software providing an easy method of system setup and

conﬁguration.

In addition to the basic components, you can also use peripheral CM9760 equipment in a System 9770, such as KBD300A keyboards (an

alternate keyboard for operator control), MDA units, ALM units, REL units, Genex

multiplexers, and Pelco VCRs.

C1555M-F (10/05) 7

MODELS

Controller and CPU Components

CM9700-CC1 CPU controller; 120 VAC, 60 Hz or 230 VAC, 50 Hz.

CM9700-SER Serial communication card (RS-422 SERCOM); provides 8 communications ports to interface peripheral equipment

(4 maximum per CPU).

CM9700-SER-32 Port expansion unit; 32 serial communication (SERCOM) ports per unit. Up to three units can be added to a CC1.

(Check with Pelco Systems Applications Department before adding to an existing CM9700-CC1). Includes

interconnecting cables and adapters for DB9 and RJ-45 connectors. Data interface can be RS-232 or RS-422.

NOTES ON USING THE SYSTEM CPU:

• You can use CM9760-CC1/CM9760-NW1 CPUs with the System 9770 if the CPU has been updated with software version level 9.01.XXX

(note that at this software level the ﬁrst three digits—9.01 in this case—must be at the same version level in the CPU (CC1 and NW1) and

in the MGR software; the remaining three digits, such as .001 in version level 9.01.001, can vary).

• Note, however, that software version level 9.01 requires a minimum of 16 MB of RAM in the CPU. If necessary, you can upgrade the RAM

in a CM9760-CC1 using the software upgrade kit appropriate for your CPU. Contact Pelco Technical Support at 1-800-289-9100 or

1-559-292-1981 for additional information.

Matrix Bay

CM9770-MXB Video matrix bay equipped with one CM9700-MPS power supply; 100-240 VAC, 50/60 Hz, autoranging.

CM9700-MPS Matrix bay power supply (spare); 120 VAC, 60 Hz or 230 VAC, 50Hz.

CM9770-DFC Downframe card and cable assembly; connects multiple matrix bays for expansion purposes.

CM9770-DFL Downframe card and cable assembly with BNC connectors for looping video.

CM9770-VCC Video camera card capable of accepting up to 32 camera inputs; also requires a rear panel card (CM9770-DFC,

CM9770-DFL, or CM9770-RPC).

CM9770-RPC Rear panel video card; provides 32 BNC connectors used to connect camera inputs to matrix bay.

CM9770-VMC Video monitor card providing 16 monitor outputs; requires CM9770-RPM.

CM9770-RPM Rear panel monitor card; provides 16 BNCs to connect monitor outputs to matrix bay; also interfaces video output

signals from video output card.

CM9700-VPP Video patch panel; provides 32 BNC connections for looping video out of system.

CM9700-VPP-RK Optional rack mount designed to hold up to 16 CM9700-VPP patch panels.

Network Interface Unit

CM9700-NW1 Network interface unit; network CPU and software necessary for joining two or more independent systems together.

8 C1555M-F (10/05)

Keyboards

The following keyboards are compatible with the System 9770:

CM9760-KBD Full-function desktop variable-speed keyboard; 120 VAC, 60 Hz.

CM9760-KBD-X Same as CM9760-KBD except 230 VAC, 50 Hz.

CM9760-KBR Full-function 19-inch EIA rack mount keyboard; 120 VAC, 60 Hz.

CM9760-KBR-X Same as CM9760-KBR except 230 VAC, 50 Hz.

KBD200A Desktop keyboard with full switching capabilities, plus push-button control of PTZ functions; 12 VAC or ±12 VDC.

(Requires KBDKIT for power.)

KBD300A Desktop keyboard with full switching capabilities, plus joystick control of PTZ functions; 12 VAC or ±12 VDC.

(Requires KBDKIT for power.)

Optional Components

CM9760-ALM Alarm interface unit; connects directly to each system; each unit can monitor up to 64 alarms; up to four units can be

connected in a series from one SERCOM port.

CM9760-CDU-T Code distribution unit; 16-channel RS-422 transmit-only (two data wires and ground) distributor. Primarily used for

wiring up to 16 pan/tilt/zoom receivers in a “star” conﬁguration.

CM9760-CXTA Coaxitron

translator; generates Coaxitron signals for Pelco Coaxitron receivers; each translator supports up to

16 receivers.

CM9760-DMR Data merger and port expander unit; this unit allows multiple CM9700-CC1 units to control multiple pan/tilt/zoom

cameras and allows multiple keyboards to communicate through one CC1 port.

CM9760-DMR-X Same as CM9760-DMR except 230 VAC, 50 Hz.

VMX200 and

VMX300 Series Video management systems; graphical map/icon-based user interface for mouse-driven operator control from

external PC.

CM9760-HS Hot switch interface unit; changeover unit that monitors the status of a primary CC1 in a 9770 system.

CM9760-MDA Master distribution ampliﬁer; inserts master time and date from the CM9700-CC1 and a programmable title of up to

24 characters on 1 to 16 video signals.

CM9760-MDA-X Same as CM9760-MDA except 230 VAC, 50 Hz.

CM9760-REL Relay interface unit; connects directly to each system and provides dry contact switching for direct or automatic

control of peripheral equipment; each unit provides up to 64 SPST contact outputs.

Genex Multiplexers Genex Series MX4009 (9-channel) and MX4016 (16-channel) multiplexers.

CM9760-VCRC CM9760-VCRC Series VCR Controller; VCR control unit capable of controlling 64 VCRs.

Compatible Receivers

Spectra

Series Spectra dome multiple protocol receiver.

ERD97P21-U Pelco P-protocol receiver.

LRD41C21-1/-2/-3 Legacy

ﬁxed speed receiver with presets.

LRD41C22-1/-2/-3 Same as LRD41C21 Series except variable speed receiver.

Esprit

Integrated pan/tilt positioning receiver.

Coaxitron Coaxitron translator allows Coaxitron control of PTZ cameras.

NOTE:

CM9760-KBD software version 8.03 or higher is required.

C1555M-F (10/05) 9

Installation

UNPACKING

1. Unpack and inspect all equipment, and verify delivery according to the packing slip.

Before shipping, Pelco connects, tests, and programs each system according to the individual sales order. Contact Pelco immediately if

there is any discrepancy in the equipment that you receive.

CM9700-CC1

The following items are supplied with the CM9700-CC1:

• 1 CM9700-CC1 unit, with front rack ears installed

• 1 120 VAC, 60 Hz power cord (USA standard)

• 1 230 VAC, 50 Hz power cord (European standard)

• 1 Keyboard, PS/2

• 1 PS/2-to-AT keyboard adapter

• 1 RCA-to-BNC adapter

• CM9700 Resource CD (includes the CM9700-MGR software)

• BNC extraction tool

• 2 Brackets with a set of 6 screws, 8-32 x .250-inch, pan head

• 2 Adjustable support rail sets (each set includes 1 front-mounting rail and 1 rear-mounting rail), with the following sets of screws

– 6 Screws, 8-32 x .375-inch, pan head with washers

– 12 Screws, 10-32 x .375-inch, ﬂat head

– 4 Screws, 10-32 x .750-inch, Phillips, pan head with washers

– 6 Screws, 8-32 x .250-inch, Phillips, pan head

CM9770-MXB

The following items are supplied with the CM9770-MXB:

• 1 CM9770-MXB matrix bay, with front rack ears installed

• 1 CM9770-MXB mounting bafﬂe, with front and rear rack ears installed

• 1 120 VAC, 60 Hz power cord (USA standard)

• 1 230 VAC, 50 Hz power cord (European standard)

• 1 RJ-45 reversed data cable

• 1 Sheet of camera number labels (these can be afﬁxed to the BNC cards to correspond to camera input numbers)

• 16 Screws and washers for mounting the bay

2. Keep all manuals and cabling with their associated equipment.

3. Locate the following documents:

• The System 9770 Port Assignments Sheet. This document contains speciﬁc information about your system. All System 9770s are

preprogrammed based on your system order.

• System 9770 manual binder.

NOTE:

The appropriate number of CM9770-VCC cards (camera cards), CM9770-VMC cards (monitor cards), and associated rear panels are

added to your system according to your system order.

10 C1555M-F (10/05)

MOUNTING

Install the System 9770 in EIA-standard 19-inch (48.26 cm) racks.

CM9770-MXB

1. Install the CM9770-MXB mounting bafﬂe ﬁrst (refer to Figure 1).

The mounting bafﬂe uses 1 rack unit (RU), and it has front and rear mounting ears, which are attached to the front and rear mounting racks.

The rear mounting brackets are adjustable to allow for different depths of cabinets.

The mounting bafﬂe provides the following functions:

• The mounting bafﬂe helps to direct the heat from a lower matrix bay (or other equipment) toward the rear of the mounting bafﬂe,

instead of allowing the heat to ﬂow up into the matrix bay.

• The mounting bafﬂe supports the weight of the matrix bay.

• The matrix bay is easier to install when it is sitting on top of the mounting bafﬂe.

Figure 1.

CM9770-MXB Mounting Bafﬂe

2. Install the CM9770-MXB matrix bay on top of the mounting bafﬂe. Refer to Figure 2.

In a single-bay installation, always leave 1 RU of space above the matrix bay for airﬂow.

In a multiple-bay installation you do not need to leave additional RUs open between units. However, you must always leave 1 RU of space

above the upper bay.

NOTE:

Be sure to use all eight screws provided with the mounting bafﬂe. The mounting bafﬂe must be installed securely to support the

weight of the matrix bay.

NOTE:

Figure 2 illustrates the recommended mounting method. For an alternate, open-rack mounting method, refer to the

Mounting the

CM9770-MXB in an Open Rack

section in the

Appendix

C1555M-F (10/05) 11

Figure 2.

Mounting the CM9770-MXB on Top of the Mounting Bafﬂe

(Optional) Install additional CM9770-MXB mounting trays and matrix bays to the side of and below the ﬁrst unit, as necessary.

3. Use the RJ-45 data cables supplied with each CM9770-MXB to connect the MXBs to the CC1. Refer to the

Data Connections

section and

the

Port Assignments

insert (supplied with the System 9770 documentation) for directions on which port to use for each MXB connection.

CM9700-CC1

The CC1 must be located near the CM9770-MXB matrix bays. The maximum distance between the CC1 and the matrix bays should be no more

than 4,000 feet (1,219 m).

The CC1 occupies 4 RUs or 7 inches (17.18 cm) of vertical space in a universal mount. Allow 1 RU of space above the CC1 for air circulation.

To install the CC1 complete the following steps and refer to Figure 3:

1. Attach one bracket to each side of the CC1 using three 8-32 x 0.250-inch pan head screws for each side. Attach each bracket so that the

slotted holes in the bracket are positioned toward the front of the CC1 and the tapered ends of the bracket are positioned toward the rear

of the CC1.

2. For each set of support rails, attach the front-mounting support rail to the rear-mounting support rail using three 8-32 x 0.375-inch pan head

screws and washers for each set. Leave the screws loose until the support rails are attached to the rack.

3. Attach one set of support rails to the equipment rack in the desired location as follows:

a. Position the ear of the front-mounting support rail against the front of the equipment rack and align the holes in the ear of the rail

with the threaded holes in the rack. Attach the ear of the rail to the rack using two 10-32 x 0.375-inch ﬂat head screws.

b. Adjust the support rails to the correct depth of the equipment rack by sliding the rear-mounting support rail to the back of the

equipment rack.

WARNING:

Always install equipment starting from the bottom of the rack frame or cabinet. Installing equipment from the top down will

make a rack or cabinet top heavy and could cause the equipment to tip over.

NOTE:

Each CM9770-MXB has a unique label for identifying the bay location in the installation. This ID information is important in

ensuring correct video and data connections.

12 C1555M-F (10/05)

c. Attach the ear of the rear-mounting support rail to the rear of the equipment rack using four 10-32 x 0.375-inch ﬂat head screws. (The

holes in the ear of the rail should align with the threaded holes in the equipment rack.)

4. Tighten the three 8-32 x 0.375-inch pan head screws and washers that were attached to the front- and rear-mounting support rails in step 2

above.

5. Repeat steps 3 and 4 for the second set of support rails.

6. Place the CC1 onto the support rails and slide the unit into the rack. The CC1 should slide in and out of the rack easily.

7. Fasten each rack ear of the CC1 to the equipment rack using two standard rack screws (10-32 x 0.750-inch Phillips pan head screws) and

washers for each ear.

Figure 3.

Mounting the CM9700-CC1

WARNING:

When sliding the CC1 out of the rack, be careful not to let the unit fall out of the rack.

REAR MOUNTING

SUPPORT RAIL

FRONT MOUNTING

SUPPORT RAIL

(8) SCREWS,

10-32 X 0.375-INCH

FLAT HEAD

(6) SCREWS,

8-32 X 0.375-INCH

PAN HEAD WITH

WASHERS

RACK

(4) SCREWS

10-32 X 0.375-INCH

FLAT HEAD

BRACKET

(SIDE VIEW)

(6) SCREWS, 8-32 X 0.250-INCH

PAN HEAD (3 EACH SIDE)

(4) SCREWS,

10-32 X 0.750-INCH

PHILLIPS, PAN HEAD

WITH WASHERS

SLOTTED HOLES

TOWARDS FRONT

OF UNIT

TAPERED ENDS

TOWARDS REAR

OF UNIT

CM9700-CC1

C1555M-F (10/05) 13

VIDEO INPUT/OUTPUT CONNECTIONS

The following steps provide an overview of how to connect video input and output sources. More complete procedures are provided in the

subsequent sections.

1. Install the CM9770-VCC and CM9770-VMC cards in the matrix bay. Refer to the

Installing Video Input Cards (CM9770-VCC)

section and the

Installing Monitor Output Cards (CM9770-VMC)

section in the following pages.

2. Slide the CM9770-RPC and CM9770-RPM BNC rear panels into the appropriate slots from the back of the matrix bay. Refer to the

Insert or

Replace a Rear Panel Video BNC Card (CM9770-RPC)

section and the

Insert or Replace a Rear Panel Monitor BNC Card (CM9770-RPM)

section in the following pages.

3. Before you connect any video input or output to the matrix bay, you may want to power up the unit to ensure that the system is operating

properly. Refer to the

Performing a Basic LED Check

section.

4. Connect video inputs and monitor outputs to the rear panel BNC connectors on the CM9770-MXB matrix bay unit(s).

Installation Tips

• Be sure each connection is secure. For best results, use crimp-on BNCs only. Do not use screw-on BNCs; these typically do not provide

adequate ground and signal connections.

• Label each video input; this can save a considerable amount of troubleshooting time in the future.

• Video output from the CM9770-VMC cards is not terminated. Terminate the video signal at the output device (monitor or VCR). If you are

looping to other devices, unterminate all but the last device.

Opening the CM9770-MXB Front Cover

To install or remove a video input card, monitor output card, or power supply, you must ﬁrst open the CM9770-MXB front cover.

1. Loosen the two screws at the top of the CM9770-MXB frame.

2. Pull the front cover towards you. The hinges at the bottom keep the cover attached to the frame.

3. When you are ﬁnished working with the interior components, close the cover and tighten the screws at the top of the frame.

NOTE:

If your System 9770 is conﬁgured by Pelco, the appropriate number of video input cards and monitor output cards and BNC rear

panels are installed at the factory, and steps 1 and 2 are not necessary. If this is the case, skip to Step 3.

NOTE:

The end point of any video cable run must be terminated in 75 ohms.

NOTE:

Although the CM9770-MXB will function properly with the front cover open, the front cover must remain closed during system

operation to meet safety standards.

14 C1555M-F (10/05)

INSTALLING VIDEO INPUT CARDS (CM9770-VCC)

The ﬁrst video input card is inserted into slot 1; the next card is inserted into slot 2 (refer to Figure 4). To add a video card, slide the card into the

ﬁrst available slot. The CM9770-MXB can contain a maximum of eight viideo input cards.

How to Turn On the Pelco V-Sync Signal

The Pelco V-Sync signal, which is sent up the coax cable, provides a synchronization pulse for cameras that can use the Pelco V-Sync signal. This

signal eliminates the vertical roll that occurs when multiple cameras are connected to the same switching device. To turn on the Pelco V-Sync

signal, move the jumper labeled “VSYNCH” on the CM9770-VCC video input card to the ON position. Refer to the CM9770-VCC Card illustration

in the Appendix to see where this jumper is located.

The Pelco V-Sync feature is either “all on” or “all off” (default) for every camera connected to the speciﬁc CM9770-VCC card. You cannot turn the

feature on or off for individual cameras.

For the Pelco V-Sync feature to work properly, all matrix bays in the system must be connected to the same power circuit (because they must be

in the same phase).

Insert or Replace a Video Card

1. Open the front of the matrix bay, insert the video card into the card guides, and slide the card partially into the bay.

2. Hold the latches parallel to the ﬂoor until you reach the edge of the bay’s frame.

3. Adjust the latches to ﬁt them properly onto the top and bottom edges of the bay’s frame.

4. Push the latching levers into the closed position; this seats the video card ﬁrmly into place.

Remove a Video Card

1. Unlatch (pull) the levers at the top and bottom portion of the video card.

2. Pull the video card towards you (towards the front of the matrix bay) until it is out of the frame.

Figure 4.

Video Input Card (CM9770-VCC) Locations: Slots 1-8

HOT SWAPPING:

You can “hot swap” a video input card—remove a card and/or insert a new card—while the system is powered and

running. When you hot swap a card, the CM9770-MXB automatically veriﬁes system software levels on all cards and then updates

software on the new cards if necessary. This process can be as fast as 30 seconds, or can take up to 5 minutes, depending on the number

of differing software ﬁles; however, the matrix bay continues to function throughout this process. The process is complete when the LEDs

marked “HB” on the front panel blink at a one-second rate.

DOWNFRAMING NOTE:

If you are downframing the video signal to additional bays, you need to turn on the Pelco V-Sync on the ﬁnal

matrix bay only.

NOTE:

Do not insert a video input card into slots 9 or 10; these slots are reserved for monitor output cards as shown in the

Monitor Output

Cards (CM9770-VMC)

section.

CM9770-VCC

SLOT 1

SLOT 2

SLOT 3

C1555M-F (10/05) 15

INSTALLING MONITOR OUTPUT CARDS (CM9770-VMC)

The monitor output card located in slot 10 is the primary card, and it handles video for monitors 1-16. Refer to Figure 5. Note that the

CM9770-MXB will not function without a CM9770-VMC card inserted into slot 10.

An optional secondary VMC card can be installed in slot 9. This card routes video for monitors 17-32.

Insert or Replace a Monitor Card

1. Open the front of the matrix bay, insert the monitor card into the card guides, and slide the card partially into the bay.

2. Hold the latches parallel to the ﬂoor until you reach the edge of the bay’s frame.

3. Adjust the latches to ﬁt them properly onto the top and bottom edges of the bay’s frame.

4. Push the latching levers into the closed position; this seats the monitor card ﬁrmly into place.

Remove a Monitor Card

1. Unlatch (pull) the levers at the top and bottom portion of the monitor card.

2. Pull the monitor card towards you (towards the front of the matrix bay) until it is out of the frame.

Figure 5.

Monitor Output Card (CM9770-VMC) Locations: Slots 9-10

HOT SWAPPING:

You can “hot swap” a monitor output card—remove a card and/or insert a new card— while the system is powered

and running. When you hot swap a card, the CM9770-MXB automatically veriﬁes system software levels on all video input cards and

monitor output cards in the matrix bay and then updates the software on any cards that do not match the VMC card in the primary VMC slot

(slot 10). This process can be as fast as 30 seconds, or can take up to 5 minutes, depending on the number of differing software ﬁles;

however, the matrix bay continues to function throughout this process. The process is complete when the LEDs marked “HB” on the front

panel blink at a one-second rate.

CAUTION:

When you insert a VMC card into the primary VMC slot—slot 10—the CM9770-MXB synchronizes software levels on all cards

in the matrix bay, based on the software contained on this card. If the new card inserted into the primary VMC slot contains software at a

lower level than the other cards in the matrix bay, you could lose some system settings and functionality.

CM9770-VMC

MONITOR CARD SLOT 9 MONITOR CARD SLOT 10

16 C1555M-F (10/05)

PERFORMING A BASIC LED CHECK

You should perform a basic LED check before you connect any video input or output to the matrix bay. The LED check allows you to ensure that

the system is operating properly.

1. Turn on the power switch on the rear of the matrix bay. The front cover can either be open or closed during the LED check.

2. Various LEDs will blink during the initialization process as the software veriﬁes communication and version level information. Once the

initialization process is complete, continue to step 3.

NOTE:

The initialization process should take approximately 30 seconds, unless the primary CM9770-VMC monitor card is updating

software on the other monitor card or on the CM9770-VCC video cards. The software update process takes several minutes.

3. Ensure that the appropriate LEDs are illuminated, as described in Table A.

4. Ensure that the red CF LED on each video input card is off. If this LED is illuminated on any input card, reseat the card. If the problem

continues, replace with a known good video input card. If this LED is illuminated on all of the video input cards, there may be a problem

with the primary monitor output card (in slot 10). Reseat the primary monitor card. If the problem continues, replace with a known good

monitor card.

5. Ensure that the red VF and PF LEDs on the power supply are off.

6. If the LEDs are properly illuminated, turn off the power switch on the rear of the matrix bay, and then install all video inputs and outputs.

Table A.

LEDs Illuminated During a Basic Check

Refer to Table H and Table I in the

Appendix

for additional information on the LEDs and troubleshooting information.

Front Panel Label Color Diagnostic Check

Power Supply

+ Green On.

- Green On.

Monitor Output Card (CM9770-VMC)

+ Green On.

- Green On.

HB Amber Blinks at a one-second rate.

RX Amber Blinks during normal system operation as switching commands are sent and polled.

MP Amber Blinks during normal system operation.

NOTE:

The amber FP, CP, and BP LEDs will blink on start-up, but should not remain illuminated.

Video Input Card (CM9770-VCC)

+ Green On.

- Green On.

HB Amber Blinks at a one-second rate.

VL Red

This is the video loss LED, and it should be illuminated because there are no video signals coming into the

rear panel yet. During normal operation this LED should be off.

NOTE:

The amber CD LED may blink on start-up, but should not remain illuminated.

C1555M-F (10/05) 17

INSTALLING REAR PANEL BNC CARDS

The following rear panel cards can be used with the CM9770-MXB matrix bay:

• CM9770-RPC—the BNC card for video connections

• CM9770-RPM—the BNC card for monitor connections

• CM9770-DFC—this is a downframe card and cable assembly used to connect multiple matrix bays; refer to the

Downframing

section in the

Appendix

for more information

• CM9770-DFL—this downframe card and cable assembly is the same as the CM9770-DFC, except that it also has BNC connectors for

looping inputs; refer to the

Downframing

section in the

Appendix

for more information

Insert or Replace a Rear Panel Video BNC Card (CM9770-RPC)

1. Slide the video BNC card into the card guides at the rear of the bay. From the rear of the bay, the slot at the far right provides the connection

point for the video input card inserted in the front of the bay into slot 1. Refer to Figure 6.

2. Push the BNC card into place ﬁrmly.

3. Tighten the screws at the top and bottom of the BNC card.

Remove a Rear Panel Video BNC Card (CM9770-RPC)

1. Loosen the screws at the top and bottom of the BNC card. Refer to Figure 7.

2. Pull the BNC card towards you until it is out of the frame.

NOTE:

You will note that the video BNC card consists of two cards connected into one unit. Each video BNC card (CM9770-RPC) provides

32 video input connections and connects to one video input card (CM9770-VCC).

Figure 6.

Insert a Rear Panel Video BNC Card (CM9770-RPC)

Figure 7.

Remove a Rear Panel Video BNC Card (CM9770-RPC)

TWO RPC CARDS ARE

CONNECTED INTO ONE

UNIT - LOOSEN SCREWS

AT TOP AND BOTTOM TO

REMOVE RPC UNIT

18 C1555M-F (10/05)

Change the Termination Jumpers on a Rear Panel Video BNC Card

In a single-bay, non-looping conﬁguration (up to 256 cameras and 32 monitors), the jumpers must be set in the terminated position. Refer to the

Installing Additional Matrix Bays—Sideframing and Downframing section in the Appendix for details on termination jumper settings in multiple-

bay conﬁgurations.

When looping video out to another device (such as a DVR, VCR, or switcher), set the termination jumpers on the CM9770-RPC cards to the

unterminated position.

The termination jumpers are set in the appropriate position when your system is conﬁgured at the factory by Pelco. However, if you expand or

change your system, or purchase a replacement CM9770-RPC card, you may need to change the termination yourself.

Since the CM9770-RPC consists of two cards assembled together, you must access the termination jumpers on each card in a different way.

Access the termination jumpers on the right-side card as shown in Figure 8. Access the termination jumpers on the left-side card as shown in

Figure 9.

Figure 13 and Figure 14 illustrate sample sideframing conﬁgurations. Figure 15 illustrates a sample downframing conﬁguration.

Refer to the

Installing Additional Matrix Bays—Sideframing and Downframing

section in the

Appendix

for detailed instructions on sideframing

and downframing.

Figure 8.

CM9770-RPC Termination Jumpers—Right Card

Figure 9.

CM9770-RPC Termination Jumpers—Left Card

C1555M-F (10/05) 19

Looping Video

When looping video out to another device (such as a DVR, VCR, or switcher), the connection instructions depend on the size of your system, as

follows:

• In a system containing 32 monitors or fewer (the video is not downframed), use the CM9700-VPP panels to loop the video out. Connect the

DFC cables that are provided with the VPP panel to the connectors on the bottom of the matrix bay RPC cards, as shown in Figure 10.

When looping video, set the termination jumpers on the CM9770-RPC cards to the unterminated position. Refer to the

Change the

Termination Jumpers on a Rear Panel Video BNC Card

section. Terminate the video signal at the ﬁnal device.

Instructions on installing the CM9700-VPP panels into an EIA-standard rack are provided in the

Appendix

• If your system contains more than 32 monitors (in a downframed conﬁguration), you must use the CM9770-DFL card in the ﬁnal bay. Use the

DFC cable that is provided with the DFC card to connect the downframe connector on the bottom of the DFL card with the DFC card in the

previous bay. This conﬁguration is illustrated in Figure 31, in the

Installing Additional Matrix Bays—Sideframing and Downframing

section

of the

Appendix

Figure 10.

Looping Video Out from the CM9770-MXB

CM9770-MXB

CM9700-VPP

DVR

PORT A PORTB

PORT APORT B

Page is loading ...

Pelco C1555M-F User manual

Brand: Pelco

Model: C1555M-F

Category: Digital Video Recorders (DVR)

Type: User manual

This manual is also suitable for

C1572M

Download PDF

report

Pelco C1555M-F User manual

This manual is also suitable for

Pelco C1555M-F User manual

Related papers

Other documents