Roland LEC-330 Installation guide

Setup Guide

Read this rst.

This describes the setup tasks and important conditions about the installation

location that must be met in order to enable use of this machine.

Most of the gures in this document depict the LEC-330.

Thank you very much for purchasing this product.

 To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through

this manual completely and store it in a safe location.

 Unauthorized copying or transferral of this manual, in whole or in part, is prohibited.

 The contents of this document and the specications of this product are subject to change without notice.

 The documentation and the product have been prepared and tested as much as possible. If you nd any misprint or

error, please inform us.

 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this

product, regardless of any failure to perform on the part of this product.

 Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to

any article made using this product.

1

Contents

Company names and product names are trademarks or registered trademarks of their respective

holders.

http://www.rolanddg.com/

To Ensure Safe Use .....................................................................................2

Pour utiliser en toute sécurité ....................................................................9

Setup Guide ........................................................................................................17

1. Installation Environment ..........................................................................18

Deciding On an Installation Site ...............................................................................................18

Temperature and Humidity ........................................................................................................19

Installation Space ...........................................................................................................................20

Air Ventilation ..................................................................................................................................20

2. Included Items .........................................................................................21

3. Assembling and Installing ........................................................................23

Step 1: Assemble the Stand ........................................................................................................23

Step 2: Mount the Machine .......................................................................................................29

Step 3: Install the Drain Bottle ...................................................................................................30

Step 4: Remove the Packing Materials ....................................................................................32

Step 5: Attach the Rear Cover ....................................................................................................34

Step 6: Attach the Media Guide ................................................................................................35

4. Connecting the Cables ............................................................................36

Connecting the Cable of the Take-up Unit ............................................................................36

Connecting the Power Cord and the Network Cable ........................................................37

5. Installing the Ink Cartridges(LEC-300A) ..................................................38

Filling with Ink for the First Time ...............................................................................................38

Installing the Ink Cartridges .......................................................................................................38

6. Installing the Ink Cartridges (LEC-330) ...................................................42

Filling with Ink for the First Time ...............................................................................................42

Axing the Cartridge-slot Labels .............................................................................................42

Selecting the Ink Mode ................................................................................................................43

Installing the Ink Cartridges .......................................................................................................46

7. Installing the Blade ..................................................................................50

8. Network Settings .....................................................................................52

Introduction .....................................................................................................................................52

Step 1: Make the Network Settings for the Computer ......................................................52

Step 2: Make the Network Settings on the Printer .............................................................54

Step 3: Make the Port Settings for the Software RIP ..........................................................56

9. Installation of Ventilating Equipment .......................................................57

Ventilating Equipment .................................................................................................................57

Installing the Ventilating Equipment ......................................................................................57

2

To Ensure Safe Use

Improper handling or operation of this machine may result in injury or damage to prop-

erty. Points which must be observed to prevent such injury or damage are described as

follows.

About WARNING and CAUTION Notices

WARNING

Used for instructions intended to alert the user to the risk of death or

severe injury should the unit be used improperly.

CAUTION

Used for instructions intended to alert the user to the risk of injury or

material damage should the unit be used improperly.

Note: Material damage refers to damage or other adverse effects

caused with respect to the home and all its furnishings, as well to

domestic animals or pets.

About the Symbols

The symbol alerts the user to important instructions or warnings. The specific

meaning of the symbol is determined by the design contained within the triangle.

The symbol at left means "danger of electrocution."

The symbol alerts the user to items that must never be carried out (are forbidden).

The specic thing that must not be done is indicated by the design contained within

the circle. The symbol at left means the unit must never be disassembled.

The symbol alerts the user to things that must be carried out. The specic thing

that must be done is indicated by the design contained within the circle. The symbol

at left means the power-cord plug must be unplugged from the outlet.

To Ensure Safe Use

3

Incorrect operation may cause injury

WARNING

Be sure to follow the operation pro-

cedures described in this documenta-

tion. Never allow anyone unfamiliar

with the usage or handling of the

machine to touch it.

Incorrect usage or handling may lead to

an accident.

Keep children away from the ma-

chine.

The machine includes areas and compo-

nents that pose a hazard to children and

may result in injury, blindness, choking,

or other serious accident.

Never operate the machine while

tired or after ingesting alcohol or any

medication.

Operation requires unimpaired judg-

ment. Impaired judgment may result in

an accident.

Never use the machine for any pur-

pose for which it is not intended, or

use the machine in an undue manner

that exceeds its capacity.

Doing so may result in injury or re.

For accessories (optional and con-

sumable items, power cord, and the

like), use only genuine articles com-

patible with this machine.

Incompatible items may lead to an ac-

cident.

Before attempting cleaning, mainte-

nance, or attachment or detachment

of optional items, disconnect the

power cord.

Attempting such operations while the

machine is connected to a power source

may result in injury or electrical shock.

CAUTION

Exercise caution to avoid being

pinched or becoming caught.

Inadvertent contact with certain areas

may cause the hand or ngers to be

pinched or become caught. Use care

when performing operations.

Never attempt operation while wear-

ing a necktie, necklace, or loose cloth-

ing. Bind long hair securely.

Such items may become caught in the

machine, resulting in injury.

Conduct operations in a clean, bright-

ly lit location.

Working in a location that is dark or clut-

tered may lead to an accident, such as

becoming caught in the machine as the

result of an inadvertent stumble.

Never climb or lean on the machine.

The machine is not made to support

a person. Climbing or leaning on the

machine may dislodge components and

cause a slip or fall, resulting in injury.

Caution: cutting tool.

This machine has an internal tool. To

avoid injury, handle the tool with care.

WARNING

Never attempt to disassemble, repair,

or modify the machine.

Doing so may result in re, electrical

shock, or injury. Entrust repairs to a

trained service technician.

To Ensure Safe Use

4

Danger of electrical short, shock, electrocution, or re

Ratings

WARNING

Connect to an electrical outlet that

complies with this machine's rat-

ings (for voltage, frequency, and

current).

Incorrect voltage or insufcient current

may cause re or electrical shock.

Never use out of doors or in any loca-

tion where exposure to water or high

humidity may occur. Never touch with

wet hands.

Doing so may result in re or electrical

shock.

Never allow any foreign object to get

inside. Never expose to liquid spills.

Inserting objects such as coins or

matches or allowing beverages to be

spilled into the ventilation ports may re-

sult in re or electrical shock. If anything

gets inside, immediately disconnect the

power cord and contact your authorized

Roland DG Corp. dealer.

Never place any flammable object

nearby. Never use a combustible

aerosol spray nearby. Never use in

any location where gases can ac-

cumulate.

Combustion or explosion may be a

danger.

WARNING

Handle the power cord, plug, and

electrical outlet correctly and with

care. Never use any article that is

damaged.

Using a damaged article may result in

re or electrical shock.

When using an extension cord or

power strip, use one that adequately

satises the machine's ratings (for

voltage, frequency, and current).

Use of multiple electrical loads on a

single electrical outlet or of a lengthy

extension cord may cause re.

Connect to ground.

This can prevent re or electrical shock

due to current leakage in the event of

malfunction.

Position so that the power plug is

within immediate reach at all times.

This is to enable quick disconnection

of the power plug in the event of an

emergency. Install the machine next to

an electrical outlet. Also, provide enough

empty space to allow immediate access

to the electrical outlet.

If sparking, smoke, burning odor,

unusual sound, or abnormal opera-

tion occurs, immediately unplug the

power cord. Never use if any compo-

nent is damaged.

Continuing to use the machine may

result in re, electrical shock, or injury.

Contact your authorized Roland DG

Corp. dealer.

To Ensure Safe Use

5

Important notes about the power cord, plug, and electrical outlet

Never place any object on top or

subject to damage.

Never bend or twist with undue force.

Never pull with undue force.

Never bundle, bind, or roll up.

Never allow to get wet.

Never make hot.

Dust may cause re.

To Ensure Safe Use

6

Ink, cleaning uid, and discharged uid are ammable and toxic

In the event of ingestion or physical distress

 In the event of contact with the eyes, immediately ush with water for at least 15 min-

utes. If eye irritation continues, seek treatment by a physician.

 In the event of contact with skin, immediately wash with soap. If irritation or inamma-

tion occurs, seek treatment by a physician.

 In the event of ingestion, do not induce vomiting, and immediately seek treatment by

a physician. Forcibly inducing vomiting may lead to danger of choking.

 If odor leads to physical distress, move to a well-ventilated location and rest quietly. If

dizziness or nausea persists, seek treatment by a physician.

WARNING

Keep open ame away from the work

area.

Ink and discharged fluid are flam-

mable.

Never store ink, cleaning fluid, or

discharged uid in any of the follow-

ing locations.

 Any location exposed to open

ame

 Any location where high tempera-

ture may occur

 Near bleach or any other such oxi-

dizing agent or explosive material

 Any location within the reach of

children

Fire may be a danger. Accidental in-

gestion by children may pose a health

hazard.

Never place an ink cartridge in re.

Ink may ow out, catch re, and spread

re to other nearby objects.

Never drink or sniff ink, cleaning uid,

or discharged uid, or allow them

to come in contact with the eyes or

skin.

Doing so may be hazardous to the

health.

CAUTION

Ensure adequate ventilation for the

work area.

Failing to perform ventilation may result

in a health hazard or danger of combus-

tion due to ink fumes.

Never allow an ink cartridge to be sub-

jected to impact, and never attempt to

disassemble.

Ink may leak.

To Ensure Safe Use

7

This machine weighs 210 kg (463 lb.). Media weighs 20 kg (44 lb.).

WARNING

Install the machine in a location that

is level, stable, and able to bear the

weight of the machine.

The total weight of the machine may

reach 210 kg (463 lb.) or more. Installa-

tion in an unsuitable location may cause

a major accident, including tip over, fall,

or collapse.

Unloading and emplacement are op-

erations that must be performed by 6

persons or more.

Tasks that require undue effort when

performed by a small number of persons

may result in physical injury. Also, if

dropped, such items may cause injury.

CAUTION

Never look at the blue-white (ultravio-

let) light emitted from the print-head

area for an extended time.

Looking directly at the ultraviolet light

from up close for an extended period

may result in eye injury.

WARNING

Be sure to lock the stand's casters.

If the machine should begin to topple,

a major accident may result, includ-

ing crushing of the appendages or the

body.

When storing roll media, implement

adequate safety measures to ensure

that the stored media will not roll, fall,

or topple over.

Danger exists of becoming pinned under

the media and suffering serious injury.

Handling roll media is an operation

that must be performed by two per-

sons or more, and care must be taken

to prevent falls.

Attempting to lift heavy media in a man-

ner that taxes your strength may cause

physical injury.

This machine uses ultraviolet light.

Caution: Ultraviolet Light

This machine is tted with covers to keep external leakage of ultraviolet light at low levels, but incorrect

handling or operation can lead to physical injury due to ultraviolet light. The extent of injury depends

on the intensity and wavelength of the ultraviolet light, and the length of time of exposure. Prolonged

exposure to strong ultraviolet light of hazardous wavelengths can cause injury to the eyes or skin.

Exercise caution.

To Ensure Safe Use

8

Warning labels are afxed to make areas of danger immediately clear. The meanings of

these labels are as follows. Be sure to heed their warnings.

Also, never remove the labels or allow them to become obscured.

Warning Labels

Ink Is Toxic

Ink and discharged uid are toxic.

Avoid contact with the body. Use only

in a well-ventilated area.

Flammable

Ink and discharged uid are ammable.

Keep away from open ame.

Caution: Moving Print Heads

The print heads inside the cover move

at high speed and pose a hazard.

Never insert the hand or ngers into

the gap.

Caution: Pinching Hazard

Be careful not to allow the ngers

to become pinched when loading

media or closing covers.

Ink Is Toxic

Ink and discharged uid are toxic.

Avoid contact with the body. Use

only in a well-ventilated area.

Flammable

Ink and discharged uid are am-

mable. Keep away from open

ame.

Caution: Pinching Hazard

Never needlessly touch the dancer roller.

Exercise caution to avoid pinching of the

ngers.

Caution: Ultraviolet Light

Never look directly from up close

for a prolonged period.

Caution: Ultraviolet Light

Never look directly from up

close for a prolonged period.

Page is loading ...

18

1. Installation Environment

Deciding On an Installation Site

Install in a quiet, stable location oering good operating conditions. An unsuitable location can cause

accident, re, faulty operation, or breakdown.

WARNING

Install the machine in a location that is level, stable, and able to

bear the weight of the machine.

The total weight of the machine may reach 210 kg (463 lb.) or more.

Installation in an unsuitable location may cause a major accident, includ-

ing tip over, fall, or collapse.

WARNING

Never install out of doors or in any location where exposure to water

or high humidity may occur.

Current leakage may cause electrical shock, electrocution, or combus-

tion and re.

WARNING

Never install close to any ammable object or in a gas-lled loca-

tion.

Combustion or explosion may be a danger.

WARNING

Install in a clean, brightly lit location.

Conduct operations in a clean, brightly lit location. Working in a location

that is dark or cluttered may lead to an accident, such as becoming caught

in the machine as the result of an inadvertent stumble.

WARNING

Position so that the power plug is within immediate reach at all

times.

This is to enable quick disconnection of the power plug in the event

of an emergency. Install the machine next to an electrical outlet. Also,

provide enough empty space to allow immediate access to the electri-

cal outlet.

CAUTION

Ensure adequate ventilation for the work area.

Failing to perform ventilation may result in a health hazard or danger of

combustion due to ink fumes.

1. Installation Environment

19

Temperature and Humidity

Maintain the specied temperature and humidity even when the machine is not in use. If temperatures

are too high or too low, it may cause malfunction.

Unsuitable Installation Sites

Following locations can cause malfunction or poor printing quality.

 Locations subject to large uctuations in temperature or humidity

 Locations subject to shaking or vibration

 Locations where the oor is tilted, not level, or unstable

 Dusty locations

 Locations exposed to direct sunlight or near air-conditioning or heating

equipment

 Locations exposed to water or moving air

 Locations exposed to considerable electrical or magnetic noise, or other

forms of electromagnetic energy

During operation: Temperature 20 to 32˚C (68 to 90˚F), relative humidity 35 to

80% (no condensation)

During non-operation: Temperature 5 to 40˚C (41 to 104˚F), relative humidity 20

to 80% (no condensation)

1. Installation Environment

20

Installation Space

The space shown in the gure is required in order to use this machine.

Air Ventilation

This machine emits a small amount of volatile compounds during printing and for some time after

printing, which may cause irritation of your eyes, nose, and throat. To use this machine, make sure to

install ventilating equipment for adequate ventilation.

? P. 57, “Installation of Ventilating Equipment”

3200mm (126 in.)

900mm (35.4 in.)

2200mm (86.6 in.)

Unit Space

Work Space

2200mm (86.6 in.)

21

* The long media clamps are installed on the machine.

2. Included Items

The following items are packed together with the unit. Make sure they are all present and accounted for.

Stay

Dancer roller Stand leg (left) Stand leg (right)

Rail slider Paper tube

Shafts Power cord

Arm / Arm retaining

screw

Drain bottle Media anges Stoppers

Drain-bottle stand Short media clamps Long media clamps * Bolts

Washers Blade Blade holder/Pin

Replacement blades for

separating knife

2 Included Items

22

SOL INK cleaning

cartridges

Hexagonal wrench

(5 mm)

Head-unit tool Software RIP

User's Manual

Setup guide

(This document)

White and Gloss Ink

Guide

Cartridge-slot labels

(Included only with LEC-330.)

Cleaning uid Cleaning sticks

INKJET PRINTER

MAINTENANCE GUIDE

Replacement wipers Tweezers

Rear cover Media guide

Rear-cover stay (left) Rear-cover stay (right) Screws Connection adapter

Cleaning kit

3. Assembling and Installing

Step 1: Assemble the Stand

WARNING

Unpacking and installation must be carried out by six or more

persons.

Otherwise the machine or the stand may fall, resulting in injury.

1.

Attach the stand legs to the stay.



Place the stay on the accessories box.



Attach the left and right stand legs to the stay.

Loosely tighten the locations shown in the gure.

Use this box

Stay

Accessories

box

Place at the center of

the stay.

Stay

Bolt

Stay

Bolt

Hexagonal

wrench

Hexagonal

wrench

Stand leg (Left)

Stand leg (Right)

3 places

23

3. Assembling and Installing

24



Tighten the remaining bolts.



Fully tighten all bolts to secure the stay and stand legs completely.



After assembling, lock all casters and remove the accessories box.

2.

Attach the rail slider and the arm.



Attach the arm to the rail slider, securing it secure with the arm retaining

screw.

Lock

Caster

Bolts

Hexagonal

wrench

Hexagonal

wrench

Bolts

4 places

Arm retaining screw

Rail slider

Orient this side toward

the rear.

Arm

3. Assembling and Installing

25



Mount the rail slider on the stand legs and secure it in place with the bolts.

Line up the tab with the slot in the rail slider and, working with the right stand leg rst, secure

in place.

3.

Attach the dancer roller.



Remove the packing material at the location shown in the gure.

Line up the tab with the slot.

Bottom surface of the rail slider

Slot

Tab

Cap-unit tool

Packing material

3. Assembling and Installing

26



Attach the dancer roller.

Secure in place using bolts, working on the right side rst.

4.

Attach the shafts and engage the brake.



Fit the stoppers onto the shafts.

Fit two stoppers onto each shaft.

Line up with the bolt hole and

secure in place.

Line up with the bolt hole and

secure in place.

Dancer roller

Orient so that this side

faces outward.

Shaft

Stopper

3. Assembling and Installing

27



Place the shafts on the stand and engage the brake.

5.

Attach the paper tube.



Pull the dancer roller back toward you.

 Engage the brake.

 Peel off the tape.

 Place the shafts on the stand.

Flip down toward

the outer side.

Dancer roller

Page is loading ...

Roland LEC-330 Installation guide

Roland LEC-330 Installation guide

in other languages

Related papers

Other documents