Roland LEC-300 Installation guide

Category
Print & Scan
Type
Installation guide

This manual is also suitable for

Setup Guide
Read this rst.
This describes the setup tasks and important conditions about the installation
location that must be met in order to enable use of this machine.
Most of the gures in this document depict the LEC-330.
Thank you very much for purchasing this product.
To ensure correct and safe usage with a full understanding of this product's performance, please be sure to read through
this manual completely and store it in a safe location.
Unauthorized copying or transferral of this manual, in whole or in part, is prohibited.
The contents of this document and the specications of this product are subject to change without notice.
The documentation and the product have been prepared and tested as much as possible. If you nd any misprint or
error, please inform us.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur through use of this
product, regardless of any failure to perform on the part of this product.
Roland DG Corp. assumes no responsibility for any direct or indirect loss or damage which may occur with respect to
any article made using this product.
1
Contents
Company names and product names are trademarks or registered trademarks of their respective
holders.
http://www.rolanddg.com/
Copyright © 2009-2012 Roland DG Corporation
Contents ........................................................................................................1
To Ensure Safe Use ....................................................................................... 2
Pour utiliser en toute sécurité .....................................................................9
Setup Guide ........................................................................................................ 17
1. Installation Environment ..........................................................................18
Deciding On an Installation Site ...............................................................................................18
Temperature and Humidity ........................................................................................................19
Installation Space ...........................................................................................................................20
Air Ventilation ..................................................................................................................................20
2. Included Items .........................................................................................21
3. Assembling and Installing ........................................................................ 23
Step 1: Assemble the Stand ........................................................................................................23
Step 2: Mount the Machine .......................................................................................................29
Step 3: Install the Drain Bottle ...................................................................................................30
Step 4: Remove the Packing Materials .................................................................................... 32
Step 5: Attach the Rear Cover ....................................................................................................34
Step 6: Attach the Media Guide ................................................................................................35
4. Connecting the Cables ............................................................................36
Connecting the Cable of the Take-up Unit ............................................................................36
Connecting the Power Cord and the Network Cable ........................................................37
5. Installing the Ink Cartridges(LEC-300A) .................................................. 38
Filling with Ink for the First Time ...............................................................................................38
Axing the Cartridge-slot Labels .............................................................................................38
Installing the Ink Cartridges .......................................................................................................40
6. Installing the Ink Cartridges (LEC-330) ...................................................45
Ink Mode ............................................................................................................................................ 45
Filling with Ink for the First Time ...............................................................................................45
Axing the Cartridge-slot Labels .............................................................................................45
Selecting the Ink Mode ................................................................................................................47
Installing the Ink Cartridges .......................................................................................................49
7. Installing the Blade ..................................................................................53
8. Network Settings .....................................................................................55
Introduction .....................................................................................................................................55
Step 1: Make the Network Settings for the Computer ......................................................55
Step 2: Make the Network Settings on the Printer .............................................................57
Step 3: Make the Port Settings for the Software RIP .......................................................... 59
9. Installation of Ventilating Equipment .......................................................60
Ventilating Equipment .................................................................................................................60
Installing the Ventilating Equipment ......................................................................................60
2
To Ensure Safe Use
Improper handling or operation of this machine may result in injury or damage to prop-
erty. Points which must be observed to prevent such injury or damage are described as
follows.
About WARNING and CAUTION Notices
WARNING
Used for instructions intended to alert the user to the risk of death or
severe injury should the unit be used improperly.
CAUTION
Used for instructions intended to alert the user to the risk of injury or
material damage should the unit be used improperly.
Note: Material damage refers to damage or other adverse effects
caused with respect to the home and all its furnishings, as well to
domestic animals or pets.
About the Symbols
The symbol alerts the user to important instructions or warnings. The specific
meaning of the symbol is determined by the design contained within the triangle.
The symbol at left means "danger of electrocution."
The symbol alerts the user to items that must never be carried out (are forbidden).
The specic thing that must not be done is indicated by the design contained within
the circle. The symbol at left means the unit must never be disassembled.
The symbol alerts the user to things that must be carried out. The specic thing
that must be done is indicated by the design contained within the circle. The symbol
at left means the power-cord plug must be unplugged from the outlet.
To Ensure Safe Use
3
Incorrect operation may cause injury
WARNING
Be sure to follow the operation pro-
cedures described in this documenta-
tion. Never allow anyone unfamiliar
with the usage or handling of the
machine to touch it.
Incorrect usage or handling may lead to
an accident.
Keep children away from the ma-
chine.
The machine includes areas and compo-
nents that pose a hazard to children and
may result in injury, blindness, choking,
or other serious accident.
Never operate the machine while
tired or after ingesting alcohol or any
medication.
Operation requires unimpaired judg-
ment. Impaired judgment may result in
an accident.
Never use the machine for any pur-
pose for which it is not intended, or
use the machine in an undue manner
that exceeds its capacity.
Doing so may result in injury or re.
For accessories (optional and con-
sumable items, power cord, and the
like), use only genuine articles com-
patible with this machine.
Incompatible items may lead to an ac-
cident.
Before attempting cleaning, mainte-
nance, or attachment or detachment
of optional items, disconnect the
power cord.
Attempting such operations while the
machine is connected to a power source
may result in injury or electrical shock.
CAUTION
Exercise caution to avoid being
pinched or becoming caught.
Inadvertent contact with certain areas
may cause the hand or ngers to be
pinched or become caught. Use care
when performing operations.
Never attempt operation while wear-
ing a necktie, necklace, or loose cloth-
ing. Bind long hair securely.
Such items may become caught in the
machine, resulting in injury.
Conduct operations in a clean, bright-
ly lit location.
Working in a location that is dark or clut-
tered may lead to an accident, such as
becoming caught in the machine as the
result of an inadvertent stumble.
Never climb or lean on the machine.
The machine is not made to support
a person. Climbing or leaning on the
machine may dislodge components and
cause a slip or fall, resulting in injury.
Caution: cutting tool.
This machine has an internal tool. To
avoid injury, handle the tool with care.
WARNING
Never attempt to disassemble, repair,
or modify the machine.
Doing so may result in re, electrical
shock, or injury. Entrust repairs to a
trained service technician.
To Ensure Safe Use
4
Danger of electrical short, shock, electrocution, or re
Ratings
WARNING
Connect to an electrical outlet that
complies with this machine's rat-
ings (for voltage, frequency, and
current).
Incorrect voltage or insufcient current
may cause re or electrical shock.
Never use out of doors or in any loca-
tion where exposure to water or high
humidity may occur. Never touch with
wet hands.
Doing so may result in re or electrical
shock.
Never allow any foreign object to get
inside. Never expose to liquid spills.
Inserting objects such as coins or
matches or allowing beverages to be
spilled into the ventilation ports may re-
sult in re or electrical shock. If anything
gets inside, immediately disconnect the
power cord and contact your authorized
Roland DG Corp. dealer.
Never place any flammable object
nearby. Never use a combustible
aerosol spray nearby. Never use in
any location where gases can ac-
cumulate.
Combustion or explosion may be a
danger.
WARNING
Handle the power cord, plug, and
electrical outlet correctly and with
care. Never use any article that is
damaged.
Using a damaged article may result in
re or electrical shock.
When using an extension cord or
power strip, use one that adequately
satises the machine's ratings (for
voltage, frequency, and current).
Use of multiple electrical loads on a
single electrical outlet or of a lengthy
extension cord may cause re.
Connect to ground.
This can prevent re or electrical shock
due to current leakage in the event of
malfunction.
Position so that the power plug is
within immediate reach at all times.
This is to enable quick disconnection
of the power plug in the event of an
emergency. Install the machine next to
an electrical outlet. Also, provide enough
empty space to allow immediate access
to the electrical outlet.
If sparking, smoke, burning odor,
unusual sound, or abnormal opera-
tion occurs, immediately unplug the
power cord. Never use if any compo-
nent is damaged.
Continuing to use the machine may
result in re, electrical shock, or injury.
Contact your authorized Roland DG
Corp. dealer.
To Ensure Safe Use
5
Important notes about the power cord, plug, and electrical outlet
Never place any object on top or
subject to damage.
Never bend or twist with undue force.
Never pull with undue force.
Never bundle, bind, or roll up.
Never allow to get wet.
Never make hot.
Dust may cause re.
To Ensure Safe Use
6
Ink, cleaning uid, and discharged uid are ammable and toxic
In the event of ingestion or physical distress
In the event of contact with the eyes, immediately ush with water for at least 15 min-
utes. If eye irritation continues, seek treatment by a physician.
In the event of contact with skin, immediately wash with soap. If irritation or inamma-
tion occurs, seek treatment by a physician.
In the event of ingestion, do not induce vomiting, and immediately seek treatment by
a physician. Forcibly inducing vomiting may lead to danger of choking.
If odor leads to physical distress, move to a well-ventilated location and rest quietly. If
dizziness or nausea persists, seek treatment by a physician.
WARNING
Keep open ame away from the work
area.
Ink and discharged fluid are flam-
mable.
Never store ink, cleaning fluid, or
discharged uid in any of the follow-
ing locations.
Any location exposed to open
ame
Any location where high tempera-
ture may occur
Near bleach or any other such oxi-
dizing agent or explosive material
Any location within the reach of
children
Fire may be a danger. Accidental in-
gestion by children may pose a health
hazard.
Never place an ink cartridge in re.
Ink may ow out, catch re, and spread
re to other nearby objects.
Never drink or sniff ink, cleaning uid,
or discharged uid, or allow them
to come in contact with the eyes or
skin.
Doing so may be hazardous to the
health.
CAUTION
Ensure adequate ventilation for the
work area.
Failing to perform ventilation may result
in a health hazard or danger of combus-
tion due to ink fumes.
Never allow an ink cartridge to be sub-
jected to impact, and never attempt to
disassemble.
Ink may leak.
To Ensure Safe Use
7
This machine weighs 210 kg (463 lb.). Media weighs 20 kg (44 lb.).
WARNING
Install the machine in a location that
is level, stable, and able to bear the
weight of the machine.
The total weight of the machine may
reach 210 kg (463 lb.) or more. Installa-
tion in an unsuitable location may cause
a major accident, including tip over, fall,
or collapse.
Unloading and emplacement are op-
erations that must be performed by 6
persons or more.
Tasks that require undue effort when
performed by a small number of persons
may result in physical injury. Also, if
dropped, such items may cause injury.
CAUTION
Never look at the blue-white (ultravio-
let) light emitted from the print-head
area for an extended time.
Looking directly at the ultraviolet light
from up close for an extended period
may result in eye injury.
WARNING
Be sure to lock the stand's casters.
If the machine should begin to topple,
a major accident may result, includ-
ing crushing of the appendages or the
body.
When storing roll media, implement
adequate safety measures to ensure
that the stored media will not roll, fall,
or topple over.
Danger exists of becoming pinned under
the media and suffering serious injury.
Handling roll media is an operation
that must be performed by two per-
sons or more, and care must be taken
to prevent falls.
Attempting to lift heavy media in a man-
ner that taxes your strength may cause
physical injury.
This machine uses ultraviolet light.
Caution: Ultraviolet Light
This machine is tted with covers to keep external leakage of ultraviolet light at low levels, but incorrect
handling or operation can lead to physical injury due to ultraviolet light. The extent of injury depends
on the intensity and wavelength of the ultraviolet light, and the length of time of exposure. Prolonged
exposure to strong ultraviolet light of hazardous wavelengths can cause injury to the eyes or skin.
Exercise caution.
To Ensure Safe Use
8
Warning labels are afxed to make areas of danger immediately clear. The meanings of
these labels are as follows. Be sure to heed their warnings.
Also, never remove the labels or allow them to become obscured.
Warning Labels
Ink Is Toxic
Ink and discharged uid are toxic.
Avoid contact with the body. Use only
in a well-ventilated area.
Flammable
Ink and discharged uid are ammable.
Keep away from open ame.
Caution: Moving Print Heads
The print heads inside the cover move
at high speed and pose a hazard.
Never insert the hand or ngers into
the gap.
Caution: Pinching Hazard
Be careful not to allow the ngers
to become pinched when loading
media or closing covers.
Ink Is Toxic
Ink and discharged uid are toxic.
Avoid contact with the body. Use
only in a well-ventilated area.
Flammable
Ink and discharged uid are am-
mable. Keep away from open
ame.
Caution: Pinching Hazard
Never needlessly touch the dancer roller.
Exercise caution to avoid pinching of the
ngers.
Caution: Ultraviolet Light
Never look directly from up close
for a prolonged period.
Caution: Ultraviolet Light
Never look directly from up
close for a prolonged period.
18
1. Installation Environment
Deciding On an Installation Site
Install in a quiet, stable location oering good operating conditions. An unsuitable location can cause
accident, re, faulty operation, or breakdown.
WARNING
Install the machine in a location that is level, stable, and able to
bear the weight of the machine.
The total weight of the machine may reach 210 kg (463 lb.) or more.
Installation in an unsuitable location may cause a major accident, includ-
ing tip over, fall, or collapse.
WARNING
Never install out of doors or in any location where exposure to water
or high humidity may occur.
Current leakage may cause electrical shock, electrocution, or combus-
tion and re.
WARNING
Never install close to any ammable object or in a gas-lled loca-
tion.
Combustion or explosion may be a danger.
WARNING
Install in a clean, brightly lit location.
Conduct operations in a clean, brightly lit location. Working in a location
that is dark or cluttered may lead to an accident, such as becoming caught
in the machine as the result of an inadvertent stumble.
WARNING
Position so that the power plug is within immediate reach at all
times.
This is to enable quick disconnection of the power plug in the event
of an emergency. Install the machine next to an electrical outlet. Also,
provide enough empty space to allow immediate access to the electri-
cal outlet.
CAUTION
Ensure adequate ventilation for the work area.
Failing to perform ventilation may result in a health hazard or danger of
combustion due to ink fumes.
1. Installation Environment
19
Temperature and Humidity
Maintain the specied temperature and humidity even when the machine is not in use. If temperatures
are too high or too low, it may cause malfunction.
Unsuitable Installation Sites
Following locations can cause malfunction or poor printing quality.
Locations subject to large uctuations in temperature or humidity
Locations subject to shaking or vibration
Locations where the oor is tilted, not level, or unstable
Dusty locations
Locations exposed to direct sunlight or near air-conditioning or heating
equipment
Locations exposed to water or moving air
Locations exposed to considerable electrical or magnetic noise, or other
forms of electromagnetic energy
During operation: Temperature 20 to 32˚C (68 to 90˚F), relative humidity 35 to
80% (no condensation)
During non-operation: Temperature 5 to 40˚C (41 to 104˚F), relative humidity 20
to 80% (no condensation)
1. Installation Environment
20
Installation Space
The space shown in the gure is required in order to use this machine.
Air Ventilation
This machine emits a small amount of volatile compounds during printing and for some time after
printing, which may cause irritation of your eyes, nose, and throat. To use this machine, make sure to
install ventilating equipment for adequate ventilation.
? P. 60, “Installation of Ventilating Equipment”
3200mm (126 in.)
900mm (35.4 in.)
2200mm (86.6 in.)
Unit Space
Work Space
2200mm (86.6 in.)
21
* The long media clamps are installed on the machine.
2. Included Items
The following items are packed together with the unit. Make sure they are all present and accounted for.
Stay
Dancer roller Stand leg (left) Stand leg (right)
Rail slider Paper tube
Shafts Power cord
Arm / Arm retaining
screw
Drain bottle Media anges Stoppers
Drain-bottle stand Short media clamps Long media clamps * Bolts
Washers Blade Blade holder/Pin
Replacement blades for
separating knife
2. Included Items
22
SOL INK cleaning
cartridges
Hexagonal wrench
(5 mm)
Head-unit tool Software RIP
User's Manual
Setup guide
(This document)
White and Gloss Ink
Guide
Cartridge-slot label
(Included only with LEC-330.)
Cleaning uid Cleaning sticks
INKJET PRINTER
MAINTENANCE GUIDE
Cartridge-slot label
Replacement wipers Tweezers
Rear cover Media guide
Rear-cover stay (left) Rear-cover stay (right) Screws Connection adapter
Cleaning kit
3. Assembling and Installing
Step 1: Assemble the Stand
CAUTION
Unpacking and installation must be carried out by six or more
persons.
Otherwise the machine or the stand may fall, resulting in injury.
1.
Attach the stand legs to the stay.
Place the stay on the accessories box.
Attach the left and right stand legs to the stay.
Loosely tighten the locations shown in the gure.
Use this box
Stay
Accessories
box
Place at the center of
the stay.
Stay
Bolt
Stay
Bolt
Hexagonal
wrench
Hexagonal
wrench
Stand leg (Left)
Stand leg (Right)
3 places
3 places
23
3. Assembling and Installing
24
Tighten the remaining bolts.
Fully tighten all bolts to secure the stay and stand legs completely.
After assembling, lock all casters and remove the accessories box.
2.
Attach the rail slider and the arm.
Attach the arm to the rail slider, securing it secure with the arm retaining
screw.
Lock
Caster
Bolts
Hexagonal
wrench
Hexagonal
wrench
Bolts
4 places
4 places
Arm retaining screw
Rail slider
Orient this side toward
the rear.
Arm
3. Assembling and Installing
25
Mount the rail slider on the stand legs and secure it in place with the bolts.
Line up the tab with the slot in the rail slider and, working with the right stand leg rst, secure
in place.
3.
Attach the dancer roller.
Remove the packing material at the location shown in the gure.
Line up the tab with the slot.
Bottom surface of the rail slider
Slot
Tab
Cap-unit tool
Packing material
3. Assembling and Installing
26
Attach the dancer roller.
Secure in place using bolts, working on the right side rst.
4.
Attach the shafts and engage the brake.
Fit the stoppers onto the shafts.
Fit two stoppers onto each shaft.
Line up with the bolt hole and
secure in place.
Line up with the bolt hole and
secure in place.
Dancer roller
Orient so that this side
faces outward.
Shaft
Stopper
Stopper
3. Assembling and Installing
27
Place the shafts on the stand and engage the brake.
5.
Attach the paper tube.
Pull the dancer roller back toward you.
Engage the brake.
Peel off the tape.
Place the shafts on the stand.
Flip down toward
the outer side.
Dancer roller
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Roland LEC-300 Installation guide

Category
Print & Scan
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages