Crestron FT2-700-ELEC Quick Start

Brand: Crestron

Model: FT2-700-ELEC

Category: Video splitters

Type: Quick Start

Crestron FT2-700-ELEC is a FlipTop cable management system designed to be installed into a table or other horizontal surface to provide connectivity for users. With eight module slots arranged in two rows of four, it can accommodate a variety of Crestron modules, including pass-through cable modules, blank plate modules, AC power outlet modules, retractor modules, USB rapid charging modules, and keystone plate modules. The system includes a power pack and power supply holder, and an additional power pack with power supply holder is required if two USB rapid charging modules are installed.

Quick Start

The Crestron® FT2-700-ELEC FlipTop™ cable management system

device, for simplicity within this document called the FlipTop assembly,

installs into a table or other horizontal surface to provide modular

tabletop connectivity for users. The one-touch lid on the unit conceals

eight module slots arranged in two rows of four.

The FlipTop assembly includes six pass-through cable modules and two

blank plate modules. Each pass-through cable module accommodates

a Crestron FT2A-CBL-PT Series Pass-Through Cable (not included) and

various other third-party interface cables. Use blank plate modules to

cover any unused module slots within the FlipTop assembly.

An included power pack, power supply holder, power cord, and DC

power splitter energize the two power buses located within the

FlipTop assembly. A second power pack with power supply holder

(not included) is required if two Crestron FT2A-CHGR-USBA/C USB

Rapid Charging Modules (not included) are installed in a single FlipTop

assembly.

The flexible modular design of the FlipTop assembly can be customized

with an assortment of Crestron accessories (not included).

NOTE: For more information about FlipTop assembly accessories, refer

to the specific product manual located at www.crestron.com/manuals.

Check the Box

Item Qty

FT2-700-ELEC 1

Bars, Locking, with Screws (P/N 4528906) 3

Cable, DC Power Splitter,Single 2.1 mm to Dual 2.1 mm

(P/N 2050094)

Holder, Power Supply (P/N 2048887) 1

Module, Blank Plate (P/N 2049602) 4

Module, Pass-Through Cable (P/N 4526880) 8

Power Cord, 5 ft 10 in. (1.78 m) (P/N 2042043) 1

Power Pack, 24 VDC, 2.5 A, 100-240 VAC (P/N 2045873) 1

Spacer, Plastic, FT2-700 (P/N 2050568) 4

Template, Cutout (P/N 4527491) 1

FT2-700-ELEC-AL Only

Bezel, FT2-700, Alloy (P/N 4529321) 1

FT2-700-ELEC-B Only

Bezel, FT2-700, Black (P/N 4529320) 1

Mount the FlipTop Assembly

Mount the FlipTop assembly into an existing FT-600 FlipTop assembly

installation or create a new mounting. The next three sections describe

the mounting procedure.

If replacing an the FT-600 FlipTop assembly, there is no need to cut a

new mounting hole (skip “Cut the Mounting Hole”).

If this is not a replacement, cut a hole and secure the FlipTop assembly

(skip “Replace FT-600 FlipTop Assembly”).

Cut the Mounting Hole

NOTE: Before cutting the mounting hole, check underneath the table

for any obstructions that may impede the installation of the FlipTop

assembly, retractors, and accessories.

1. Trace an outline of the mounting hole onto the table using the

included cutout template.

2. Cut a mounting hole in the table with an appropriate saw.

Replace FT-600 FlipTop Assembly

To replace an older FT-600 FlipTop assembly with an FT2-700 FlipTop

assembly:

1. Remove the FT-600 FlipTop assembly by loosening four socket

screws that secure two mounting plates and the FlipTop

assembly to the surface.

2. Attach four plastic spacers (included) to each corner of the

FT2-700 FlipTop assembly prior to inserting into the mounting

hole previously cut for the FT-600 FlipTop assembly.

Location of Plastic Spacers on FlipTop Assembly Corners

(Enlarged View)

Flat portion

must face

upward.

Plastic

spacer (4)

FT2-700

FlipTop

assembly

(top front)

Clip a plastic spacer into two slots

on each corner of FlipTop assembly.

Secure the FlipTop Assembly

To secure the FlipTop assembly:

1. If using a single power supply, connect the dual connector ends

of the included DC power splitter cable to the two barrel jacks in

the bottom of the power bus so the cable may be accessed later.

For location of the barrel jacks, refer to “Connect the FlipTop

Assembly.”

DC Power Splitter Cable (Included)

2. Ensure that all four swiveling dogs are positioned inside of

the FlipTop assembly, and then insert the assembly into the

mounting hole until the top lip is flush with the table surface.

CAUTION: Set the screwdriver torque to its lowest setting to

avoid stripping the swiveling dogs and damaging the table.

If removing the FlipTop assembly from the table, ensure that

the screwdriver rotation is set correctly before loosening the

swiveling dogs.

3. Carefully tighten the four swiveling dogs in each corner of the

FlipTop assembly clockwise until the assembly is secured in place

against the table. Do not overtighten the swiveling dogs.

Location of Swiveling Dogs

Swiveling dogs (4)

FT2-ELEC

assembly

Retractable lid

(in rear of

assembly)

Connect and Place the Power Supply

Access the two network connectors and two power bus barrel jacks on

the underside of the FlipTop assembly.

Location of Power Bus Barrel Jacks

FlipTop

power bus

barrel jacks

FlipTop

assembly

(bottom view)

The FlipTop assembly ships with one 24 VDC power supply that is

used to supply power to the power bus in the assembly. There are six

possible locations to attach the power supply. Connect the power

supply prior to installing any modules.

NOTE: Two power supplies are required if installing two

FT2A-CHGR-USBA/C modules in the FlipTop assembly. For more

information, refer to the FT2A-CHGR-USBA/C Installation Guide

(Doc. 8219) at www.crestron.com/manuals.

To connect the power supply to the power bus:

1. Underneath the table, connect the power supply to the bottom

of the power bus:

• If connecting one power supply, connect the power

supply’s power cord to the single connector end of the DC

power splitter cable. Refer to step 1 in “Secure the FlipTop

Assembly.”

• If connecting two power supplies, connect each power

supply’s power cord to a barrel jack in the power bus.

2. Use the two included tie wraps to dress the power cord.

3. Slide the power supply into the power supply holder until it is

secured in place.

4. Insert the power supply holder into the side of the FlipTop

assembly so that the four mounting posts on the rear of the

holder engage the four rectangular slots in one of the six

mounting locations.

Location of Power Supply

Power

supply

holder

Power

supply

FlipTop

assembly

5. Slide the holder downward until it is secured to the FlipTop

assembly.

Mounting Locations of Power Supply

Power supply

mounting locations (6)

6. Connect the included 5 ft 10 in. (1.78 m) power cord to the power

jack on top of the power supply, and then connect the other end

to a power source. Do not apply power until all modules have

been installed and all connections have been made to the FlipTop

assembly.

Install the Modules

NOTE: Installation procedures for most modules are available in

separate product documentation. For more information, refer to the

specific product manual located at www.crestron.com/manuals.

The following sections provide best practices and installation

procedures for pass-through cable modules and blank plate modules.

Position the Modules

NOTE: The FlipTop assembly includes six FT2A-PLT-PT pass-through

cable modules and two FT2A-PLT-BLANK blank plate modules. No

other modules are included.

FT2-700-ELEC

FlipTop™ Cable Management System FT2 Series, 700 Size, Electrical

Follow the best practices below when performing module installation.

• Perform module installation in the following order:

1. AC Power Outlet Modules (FT2A-PWR-US)

2. Retractor modules (FT2A-CBLR-1T and FT2A-CBLR-GR)

3. All other modules (FT2A-CP, FT2A-CHGR-USBA/C,

FT2A-PLT-PT, and FT2A-PLT-BLANK)

• Place the FT2A-CBLR-GR modules only at the ends of a module

row.

• Dress all cables after installing each module.

Install the Pass-Through Cable Module

Each pass-through cable module is packaged with one nylon grommet

and one cable plate. One empty module slot is required for installation.

To assemble and install the pass-through cable modules into the FlipTop

assembly:

1. Separate the grommet.

2. Insert the cable into the grommet with the connector facing up

toward the end user.

NOTE: The grommet is optional. It fits 10mm or smaller cables

(non-4K cables such as USB, CAT6, VGA, and audio). Omit the

grommet if installing larger cables (such as Crestron 4K video

cables) into the module.

3. Press the grommet back together to secure the cable inside.

4. Push the grommet and cable into the hole in the cable plate.

5. Insert the cable plate into one of the three slots in the

pass-through module. The top of the cable connector should sit

flush with the top of the module.

NOTE: If the cable connector extends past the top of the

pass-through module, the FlipTop assembly lid cannot close.

Location of Cable Plates within the Pass-Through Cable Module

The cable plate

with the nylon

grommet may be

installed in one of

these three slots.

Pass-through

module (with side

plate removed)

6. Attach the side plate to the module by snapping the plastic clips

on the plate into the two slots on the module.

NOTE: Ensure that the cable moves freely in the module prior to

attaching the side plate, as the plate is difficult to remove once

it is attached. If the side plate must be removed, use a small, flat

object (such as a flat-head screwdriver) to carefully pry the plastic

clips on the side plate off of the module near the two slots.

Location of Plastic Clips on Side Panel

Snap to attach

(or pry to remove)

the plastic clips

from the slots on

a pass-through

module.

7. Feed the other end of the cable through an empty module slot in

the FlipTop assembly.

8. Slide the pass-through cable module into the empty module slot

in the FlipTop assembly. Use the guide ribs on the front and rear of

each module to help position the module in the assembly.

Install the Blank and Keystone Plate Module

Four blank plate modules are included to fill empty slots in module

rows. A keystone plate module allows for cables terminated with

standard keystone jacks to be installed in the FlipTop assembly. The

blank and keystone modules each require one empty module slot for

installation.

Blank and Keystone Plate Modules

Blank plate module

Keystone plate module

To install a blank or keystone plate module into the FlipTop assembly:

• Slide the blank plate module down into the appropriate module

slot. Use the guide ribs on the front and rear of each module to

help position it in the assembly.

• For the keystone plate module, complete the following.

1. Snap the cable’s keystone jack into the keystone opening in the

keystone plate module.

2. Feed the cable down through the empty module slot.

3. Slide the attached keystone plate module down into the same

module slot using the front and rear guide ribs to assist with

positioning.

Install the Locking Bars

1. Place the locking bars into position so that the screws attached to

the locking bars engage the screw holes in the FlipTop assembly.

2. Using a manual torque screwdriver set to its lowest possible

setting, hand tighten the locking bar screws until the locking bars

are secured to the FlipTop assembly.

CAUTION: Do not overtighten the locking bar screws.

Position of Locking Bars

FT2-MECH

assembly

FT2A modules

Locking bars (3)

Install the Bezel

Place the bezel onto the FlipTop assembly so that the retractable lids fit

inside the bezel openings. The bezel is held in place using magnets.

Position of Bezel

Bezel opening

for retractable lid

Retractable lid

Lid retraction

button

Operate the FlipTop Assembly

To operate the FlipTop assembly:

1. Tap the lid retraction button to retract the one-touch lid, which

disappears into the assembly.

2. Pull out a cable and lay it on the tabletop.

3. Lift the cable vertically above the FlipTop assembly to retract the

cable gently back into the assembly.

4. Close the lid by lifting it vertically and returning it over the FlipTop

assembly.

Additional Information

Scan or click the QR code for detailed product information on the

Crestron website.

FT2-700-ELEC

Compliance and Legal

Original Instructions: The U.S. English version of this document is the original instructions. All

other languages are a translation of the original instructions.

As of the date of manufacture, the product has been tested and found to comply with

specifications for CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions: (1) This device may not cause harmful interference and (2) this device must accept

any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible

for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

The product warranty can be found at www.crestron.com/warranty.

The specific patents that cover Crestron products are listed at

www.crestron.com/legal/patents.

Certain Crestron products contain open source software. For specific information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, and FlipTop are either trademarks or registered trademarks of

Crestron Electronics, Inc. in the United States and/or other countries. The UR logo is either a

trademark or registered trademark of Underwriters Laboratories, Inc. in the United States

and/or other countries. Other trademarks, registered trademarks, and trade names may be

used in this document to refer to either the entities claiming the marks and names or their

products. Crestron disclaims any proprietary interest in the marks and names of others.

Crestron is not responsible for errors in typography or photography.

Crestron Electronics, Inc.

15 Volvo Drive, Rockleigh, NJ 07647

Tel: 888.CRESTRON

Fax: 201.767.7576

www.crestron.com

Quick Start - Doc. 8244E

(2053626)

05.19

Specifications subject to

change without notice.

Crestron FT2-700-ELEC Quick Start

Brand: Crestron

Model: FT2-700-ELEC

Category: Video splitters

Type: Quick Start

Download PDF

report

Crestron FT2-700-ELEC Quick Start

Crestron FT2-700-ELEC Quick Start

Related papers

Other documents