Crestron FT2-1200-ELEC lets you integrate power and connectivity into your conference or meeting room table. It features 6 pass-through cable modules and 3 blank plates, customizable with accessories like cable retractors, active connector plates, and power outlets. Charge devices with the USB rapid charging module. Automate one-touch retractors with a control system for a tidy setup.
Crestron FT2-1200-ELEC lets you integrate power and connectivity into your conference or meeting room table. It features 6 pass-through cable modules and 3 blank plates, customizable with accessories like cable retractors, active connector plates, and power outlets. Charge devices with the USB rapid charging module. Automate one-touch retractors with a control system for a tidy setup.
Quick Start
The Crestron® FT2-1200-ELEC FlipTop™ cable management system
device, for simplicity within this document called the FlipTop assembly,
installs into a table or other horizontal surface to provide modular
tabletop connectivity for users. The one-touch lid on the unit conceals
nine module slots arranged in a single row.
The FlipTop assembly includes six pass-through cable modules
and three blank plate modules. Each pass-through cable module
accommodates a Crestron FT2A-CBL-PT Series Pass-Through Cable
(not included) and various other third-party interface cables. Use blank
plate modules to cover any unused module slots within the FlipTop
assembly. An included power pack, power supply holder, and power
cord energize the power bus located within the FlipTop assembly.
The flexible modular design of the FlipTop assembly can be customized
with an assortment of Crestron accessories (not included):
• FT2A-CBL-PT is a series of pass-through cables optimized for
the provided pass-through cable modules.
• FT2A-CBLR-GR is a series of gravity cable retractors. Each cable
in the retractor pulls out up to 3 feet (0.9 m) and retracts gently
back into the FlipTop assembly.
• FT2A-CBLR-1T is a series of one-touch cable retractors. Each
cable in the retractor pulls out up to 5 ft (1.5 m) and retracts
when the cable retractor button is pressed or a Crestron control
system automatically retracts the cable.
• FT2A-CP is a series of active connector plate modules. Each
module provides panel mounted connectors, which allow the
connection of devices using separate, detached interface cables
(not included).
• FT2A-CHGR-USBA/C is a USB rapid charging module. It provides
one USB Type-C™ charging port and one USB Type-A charging
port.
• FT2A-PWR-US is a series of AC power outlet modules that
provide one or more NEMA 5 type receptacles above the table.
The basic model provides one additional outlet below the table;
the other models provide two.
• FT2A-UTK-SHELF in an under-table utility shelf capable of
holding HDMI® switches or HDBaseT® transmitters.
• FT2A-PLT-BLANK-10 is a pack of 10 blank plate modules used
to supplement those provided with the FlipTop assembly. Each
module covers one unused module slot within the assembly.
• FT2A-PLT-PT-10 is a pack of 10 pass-through cable modules used
to supplement those provided with the FlipTop assembly. Each
module accommodates a Crestron FT2A-CBL-PT Series
Pass-Through Cable or a third-party interface cable.
NOTE: For more information about FlipTop assembly
accessories, refer to the specific product manual located at
www.crestron.com/manuals.
Check the Box
Item Qty
FT2-1200-ELEC 1
Bars, Locking, with Screws (P/N 4527589) 2
Connector, 3-Pin (P/N 2003575) 1
Holder, Power Supply (P/N 2048887) 1
Module, Blank Plate (P/N 2049602) 3
Module, Pass-Through Cable (P/N 4526880) 6
Power Cord, 5 ft 10 in. (1.78 m) (P/N 2042043) 1
Power Pack, 24 VDC, 2.5 A, 100-240 VAC (P/N 2045873) 1
Template, Cutout (P/N 4528347) 1
Tie Wrap (P/N 2047935) 1
FT2-1200-ELEC-AL Only
Bezel, FT2-1200, Alloy (P/N 4528342) 1
FT2-1200-ELEC-B Only
Bezel, FT2-1200, Black (P/N 4528341) 1
Mount the FlipTop Assembly
The next two sections describe the mounting procedure.
Cut the Mounting Hole
NOTE: Before cutting the mounting hole, check underneath the table
for any obstructions that may impede the installation of the FlipTop
assembly, retractors, and accessories.
1. Trace an outline of the mounting hole onto the table using the
included cutout template.
2. Cut a mounting hole in the table with an appropriate saw.
Secure the FlipTop Assembly
To secure the FlipTop assembly:
1. Ensure that the two swiveling dogs are positioned inside of
the FlipTop assembly, and then insert the assembly into the
mounting hole until the top lip is flush with the table surface.
CAUTION: Set the screwdriver torque to its lowest setting to
avoid stripping the swiveling dogs and damaging the table.
If removing the FlipTop assembly from the table, ensure that
the screwdriver rotation is set correctly before loosening the
swiveling dogs.
2. Carefully tighten the two swiveling dogs in the FlipTop assembly
clockwise until the assembly is secured in place against the table.
Do not overtighten the swiveling dogs.
Location of Swiveling Dogs
Swiveling
dogs (2)
Retractable
lid
FlipTop
assembly
Connect the FlipTop Assembly
Access the network connector and power bus barrel jack on the
underside of the FlipTop assembly.
Location of 3-Pin Network Connector and Power Bus Barrel Jack
Power bus
barrel jack
3-Pin network
connector
FlipTop assembly
(bottom view)
Connect the Network
Automate one touch retractors by connecting all the retractors in a
FlipTop to a control system and a switch, or to a DMPS via a single
Cresnet® cable. Custom programming can trigger all the retractors
after five minutes of no video detected.
Connect the FlipTop assembly to a Crestron control system or DMPS3
via the 3-pin connector using standard Cresnet cable. The red power
lead is not connected and should be terminated.
3-Pin Connector with Wires Attached
White (Y)
Blue (Z)
Black (G)
Connect and Place the Power Supply
The FlipTop assembly ships with one 24 VDC power supply that is
used to supply power to the power bus in the assembly. There are four
possible locations to attach the power supply. Connect the power
supply prior to installing any modules.
To connect the power supply to the power bus:
1. Underneath the table, connect the power supply to the bottom
of the power bus.
2. Use the included tie wrap to dress the power cord.
3. Slide the power supply into the power supply holder until it is
secured in place.
4. Insert the power supply holder into the side of the FlipTop
assembly so that the four mounting posts on the rear of the
holder engage the four rectangular slots in one of the four
mounting locations.
Location of Power Supply
FlipTop
assembly
Power
supply
Rectangular
slots (4)
Power
supply
holder
5. Slide the holder downward until it is secured to the FlipTop
assembly.
Mounting Locations of Power Supply
Power supply
mounting locations (4)
6. Connect the included 5 ft 10 in. (1.78 m) power cord to the power
jack on top of the power supply, and then connect the other end
to a power source. Do not apply power until all modules have
been installed and all connections have been made to the FlipTop
assembly.
FT2-1200-ELEC
FlipTop™ Cable Management System FT2 Series, 1200 Size, Electrical
Install the Modules
NOTE: Installation procedures for most modules are available in
separate product documentation. For more information, refer to the
specific product manual located at www.crestron.com/manuals.
The following sections provide best practices and installation
procedures for pass-through cable modules and blank plate modules.
Position the Modules
NOTE: The FlipTop assembly includes six FT2A-PLT-PT pass-through
cable modules and three FT2A-PLT-BLANK blank plate modules. No
other modules are included.
Follow the best practices below when performing module installation.
• Perform module installation in the following order:
1. AC Power Outlet Modules (FT2A-PWR-US)
2. Retractor modules (FT2A-CBLR-1T and FT2A-CBLR-GR)
3. All other modules (FT2A-CP, FT2A-CHGR-USBA/C,
FT2A-PLT-PT, and FT2A-PLT-BLANK)
• Place the FT2A-CBLR-GR modules only at the ends of the module
row.
• Dress all cables after installing each module.
Install the Pass-Through Cable Module
Each pass-through cable module is packaged with one nylon grommet
and one cable plate. One empty module slot is required for installation.
To assemble and install the pass-through cable modules into the FlipTop
assembly:
1. Separate the grommet.
2. Insert the cable into the grommet with the connector facing up
toward the end user.
NOTE: The grommet is optional. It fits 10mm or smaller cables
(non-4K cables such as USB, CAT6, VGA, and audio). Omit the
grommet if installing larger cables (such as Crestron 4K video
cables) into the module.
3. Press the grommet back together to secure the cable inside.
4. Push the grommet and cable into the hole in the cable plate.
5. Insert the cable plate into one of the three slots in the
pass-through module. The top of the cable connector should sit
flush with the top of the module.
NOTE: If the cable connector extends past the top of the
pass-through module, the FlipTop assembly lid cannot close.
Location of Cable Plates within the Pass-Through Cable Module
The cable plate
with the nylon
grommet may be
installed in one of
these three slots.
Pass-through
module (with side
plate removed)
6. Attach the side plate to the module by snapping the plastic clips
on the plate into the two slots on the module.
NOTE: Ensure that the cable moves freely in the module prior to
attaching the side plate, as the plate is difficult to remove once
it is attached. If the side plate must be removed, use a small, flat
object (such as a flat-head screwdriver) to carefully pry the plastic
clips on the side plate off of the module near the two slots.
Location of Plastic Clips on Side Panel
Snap to attach
(or pry to remove)
the plastic clips
from the slots on
a pass-through
module.
7. Feed the other end of the cable through an empty module slot in
the FlipTop assembly.
8. Slide the pass-through cable module into the empty module slot
in the FlipTop assembly. Use the guide ribs on the front and rear of
each module to help position the module in the assembly.
Install the Blank Plate Module
Three blank plate modules are included to fill empty slots in the module
row. Each module requires one empty module slot for installation.
Blank Plate
Blank plate
To install a blank plate module into the FlipTop assembly, slide the
module down into the appropriate module slot. Use the guide ribs on
the front and rear of the module to help position it in the assembly.
Install the Locking Bars
1. Place the locking bars into position so that the screws attached to
the locking bars engage the screw holes in the FlipTop assembly.
2. Using a manual torque screwdriver set to its lowest possible
setting, hand tighten the locking bar screws until the locking bars
are secured to the FlipTop assembly.
CAUTION: Do not overtighten the locking bar screws.
Position of Locking Bars
Locking
bars (2)
FlipTop
assembly
Install the Bezel
Place the bezel onto the FlipTop assembly so that the retractable lid fits
inside the bezel opening. The bezel is held in place using magnets.
Position of Bezel
Lid
retraction
button
Retractable
lid
Bezel
opening for
retractable
lid
Operate the FlipTop Assembly
To operate the FlipTop assembly:
1. Tap the lid retraction button to retract the one-touch lid, which
disappears into the assembly.
2. Pull out a cable and lay it on the tabletop.
3. Lift the cable vertically above the FlipTop assembly to retract the
cable gently back into the assembly.
4. Close the lid by lifting it vertically and returning it over the FlipTop
assembly.
For Additional Information
Scan or click the QR code for detailed product information on the
Crestron website.
FT2-1200-ELEC
Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All
other languages are a translation of the original instructions.
As of the date of manufacture, the product has been tested and found to comply with
specifications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Statement
CAN ICES-3 (B)/NMB-3(B)
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at
www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource.
Crestron, the Crestron logo, Cresnet, and FlipTop are either trademarks or registered
trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT
is either a trademark or registered trademark of the HDBaseT Alliance in the United States
and/or other countries. HDMI and the HDMI logo are either trademarks or registered
trademarks of HDMI Licensing LLC in the United States and/or other countries. The UR logo
is either a trademark or registered trademark of Underwriters Laboratories, Inc. in the United
States and/or other countries. USB Type-C is either a trademark or registered trademark of
the USB Implementers Forum in the United States and/or other countries. Other trademarks,
registered trademarks, and trade names may be used in this document to refer to either the
entities claiming the marks and names or their products. Crestron disclaims any proprietary
interest in the marks and names of others. Crestron is not responsible for errors in typography
or photography.
©2019 Crestron Electronics, Inc.
Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start - Doc. 8407B
(2052790)
04.19
Specifications subject to
change without notice.
-
1
-
2
Crestron FT2-1200-ELEC lets you integrate power and connectivity into your conference or meeting room table. It features 6 pass-through cable modules and 3 blank plates, customizable with accessories like cable retractors, active connector plates, and power outlets. Charge devices with the USB rapid charging module. Automate one-touch retractors with a control system for a tidy setup.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Crestron FT2-1400-ELEC Quick Start
-
-
-
-
-
-
-
-
-
