Draw-Tite 41547 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
41547
Category
Car kits
Type
Installation guide

Draw-Tite 41547 is a towing hitch designed for use with Ford F-350, F-450, and F-550 trucks with a 34-inch frame. It has a weight distributing hitch rating of 12,000 lb. max gross trailer weight and 1,200 lb. max tongue weight, and a weight carrying hitch rating of 6,000 lb. max gross trailer weight and 600 lb. max tongue weight. The hitch is made of high-strength steel and features a durable black powder coat finish. It comes with all necessary hardware for installation, including bolts, locknuts, and washers.

Draw-Tite 41547 is a towing hitch designed for use with Ford F-350, F-450, and F-550 trucks with a 34-inch frame. It has a weight distributing hitch rating of 12,000 lb. max gross trailer weight and 1,200 lb. max tongue weight, and a weight carrying hitch rating of 6,000 lb. max gross trailer weight and 600 lb. max tongue weight. The hitch is made of high-strength steel and features a durable black powder coat finish. It comes with all necessary hardware for installation, including bolts, locknuts, and washers.

1/2" CARRIAGE BOLT
BOLT PLATE
1/2" SERRATED WASHER
1/2" LOCK WASHER
1/2" NUT
5/8" FLAT WASHER
5/8" LOCK WASHER
5/8" HEX HEAD BOLT
5/8" FLAT WASHER
5/8" NUT
INSTALLATION INSTRUCTIONS
Product No.
41547
TOOLS REQUIRED
3/4” SOCKET
15/16” SOCKET
15/16” WRENCH
5/8” DRILL
2- CLAMPS
TORQUE WRENCH
SMALL PARTS
PACKAGE F41547
WARNING:
DO NOT LUBRICATE THREADS, BOLT FAILURE MAY
OCCUR DUE TO OVER TIGHTENING.
WARNING:
DO NOT DRILL OR WELD TO THIS HITCH
.
IMPORTANT NOTES
USE ONLY TOWING PRODUCTS SUPPLIED OR APPROVED BOLTS,
LOCKNUTS, AND WASHERS TO INSTALL THIS HITCH
(OVER)
FORD F-350, F-450, & F-550
With 34” Frame
1. Hold the hitch up under the frame. Position the holes in the brackets over the rivet heads at the rear of the frame. Clamp the
hitch in place.
2. Install 1/2” carriage bolts with bolt plates down through the holes in the frame beside the spring hangers. Install 1/2” serrated
washers, 1/2” lock washers, and 1/2” nuts on the bolts. See diagram above. It may be necessary to screw the 1/2” carriage
bolt with bolt plate onto the pull wire. Some gas tanks will limit access to the hole inside the frame. Use the pull wire to pull
the bolt into the hole in the frame. Feed the wire through from a more open area in the frame.
3. Using the rear holes in the bracket as a guide, drill a 5/8” hole into the bottom of the frame. Install the 5/8” bolts with 5/8” flat
washers down through the frame and through the brackets. Install 5/8” flat washers, 5/8” lock washers, and 5/8” nuts on the
bolts. See diagram above.
4. Torque 5/8” nuts to 115 ft*lbs.
Torque 1/2” nuts to 70 ft*lbs.
1/2" PULL
WIRE 55392
PLYMOUTH, MI
N41547-12-16-02 EWO3289 © 2002 TOWING PRODUCTS, INC. Litho in USA
LIMITED WARRANTY
THIS PRODUCT COMPLIES WITH SAFETY SPECIFICATION AND REQUIREMENTS FOR THE STATE OF NEW YORK AND VESC REGULATION V-5 FOR CONNECTING DEVICES AND
TOWING SYSTEMS. WEIGHT DISTRIBUTING HITCH RATING IS 12000 LB. MAX. GROSS TRAILER WEIGHT AND 1200 LB. MAX. TONGUE WEIGHT. WEIGHT CARRYING HITCH RATING IS
6000 LB MAX GROSS TRAILER WEIGHT AND 600 LB MAX TONGUE WEIGHT. CONSULT VEHICLE OWNERS MANUAL FOR TOWING RECOMMENDATIONS AND LIMITATIONS.
1/2" HEX BOLT
1/2" NUT
1/2" LOCK WASHER
1/2" SERRATED WASHER
BOLT PLATE
1/2" CARRIAGE BOLT
1/2" NUT
1/2" LOCK WASHER
TOOLS REQUIRED
3/4” SOCKET
3/4” WRENCH
TORQUE WRENCH
1. Hold the hitch up under the frame. Position the holes in the brackets over the rivet heads at the rear of the frame.
2. Insert 1/2” hex head bolts into the plate that extends down from the frame. Install 1/2” lock washers, and 1/2” nuts on all four bolts.
See diagram above. It may be necessary to screw the 1/2” carriage bolt with bolt plate onto the pull wire. Some gas tanks will
limit access to the hole inside the frame. Use the pull wire to pull the bolt into the hole in the frame. Feed the wire through a
more open area in the frame.
2. Install 1/2” carriage bolts with bolt plates down through the holes in the frame beside the spring hangers. Install 1/2” serrated
washers, 1/2” lock washers, and 1/2” nuts on the bolts. See diagram above.
4. Torque 1/2” nuts to 70 ft*lbs.
INSTALLATIONS FOR:
FONTAINE CONVERSIONS
1/2" PULL
WIRE 55392
Towing Products warrants its Hitches, custom Hitch Receivers, and Sway Controls from date of purchase against defects in material and
workmanship under normal use and service, ordinary wear excepted, for the ownership life of the original consumer purchaser. Towing Products
will replace FREE OF CHARGE any part which proves defective in material or workmanship when presented to any Towing Products dealer,
Towing Products Warehouse, or returned to factory, TRANSPORTATION CHARGES PREPAID, at the address below. THIS WARRANTY IS
LIMITED TO DEFECTIVE PARTS REPLACEMENT ONLY. LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION OR
REPLACEMENT AS WELL AS INCIDENTAL AND CONSEQUENTIAL DAMAGES CONNECTED THEREWITH ARE EXCLUDED. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any damage
to the Hitch, Custom Hitch receiver or Sway Control as a result of misuse, abuse, neglect, accident, improper installation, or any use violative of
instructions furnished by Towing Products, WILL VOID THE WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. In the event of a problem
with warranty service or performance, you may be able to go to a small claims court, a state court, or a federal district court.
Towing Products
PO Box 8102
47774 Anchor Ct.
Plymouth, MI 48170
Towing Products
2351 Winston Park Drive
Oakville, Ontario
Canada L6H6R7
N41547-12-16-02 EWO3289 © 2002 TOWING PRODUCTS Litho in USA
  • Page 1 1
  • Page 2 2

Draw-Tite 41547 Installation guide

Draw-Tite
Brand
Draw-Tite
Model
41547
Category
Car kits
Type
Installation guide

Draw-Tite 41547 is a towing hitch designed for use with Ford F-350, F-450, and F-550 trucks with a 34-inch frame. It has a weight distributing hitch rating of 12,000 lb. max gross trailer weight and 1,200 lb. max tongue weight, and a weight carrying hitch rating of 6,000 lb. max gross trailer weight and 600 lb. max tongue weight. The hitch is made of high-strength steel and features a durable black powder coat finish. It comes with all necessary hardware for installation, including bolts, locknuts, and washers.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents