Terms such as “left” and “right” refer to the location when facing the completed sauna from the front, or glass side.

Place the oor section in the location where you will want the sauna and position the rear wall so that it is on the

outside of the oor section as shown (1). Find the rear wall sections, left and right, and position so that they are

outside the oor section. You can distinguish left and right by the upright boards beneath the heater panels as shown

in image (2). Clip the buckles on the back side of the rear wall sections to draw them together (3). Find the right

wall section (with single heater panel) and position so that it is outside the oor section and aligns with the rear wall

section (4).

Screw the right wall section to the rear wall using the 3” screws as shown (5). v Find the left wall section (with three

heater panels) and position so that it is outside the oor section and aligns with the rear wall section. Screw to the

rear wall using 3” screws. Figure (6) shows the inside of the sauna after side and rear walls are in place. Note: The oor

will be supported by the bench supports as well as vertical support boards located on the side wall and right-side

bench support (11). Find the front upper bench support. Position and screw in place as shown. Plug into second wire

coming from rear panel (12).

Place the upper bench in place which will be supported by side and rear wall horizontal supports and right-side

bench support (13). View of interior of sauna after benches are in place(14). Secure the back rest to the rear wall

using 2” screws. Note: Be sure the back rest is level and positioned approximately 2” above the bench (15). Find the 2

vertical front wall frame pieces which have slotted brackets as well as 2 horizontal frame pieces with notched tongues

protruding from the ends (16).

Using a rubber mallet, gently tap the side frame pieces into the lower horizontal frame piece (17). Screw the horizontal

frame piece to the vertical frame piece as shown (18). Lean the partially completed front wall frame against a wall with

Position the top horizontal frame piece, ensuring that the glass is in the grooves and the tongue ts into the groove on

the vertical frame pieces. Screw into place as shown (21). With two people, position the assembled front wall section

so that the pins align with the slots (22). Gently lift the front wall section so that the pin will insert into the large

portion of the slot at the top, middle and bottom of each side (23). Then lower the wall section so that the pin slides

into the narrow part of the slots. This will secure the front wall section to the left and right wall sections. Use a rubber

mallet if necessary, to assist in lowering the front wall section to the height of the left and right wall sections (24).

Find the heater wire connections at the top of the panels and move them so they lay to the outside of the sauna for

into the rear and side wall sections as shown. Use 4 screws on the rear and two on each of the side walls (28).

Feed the power connectors through the holes in the dust cover and reposition the dust cover over the roof section.

Re-attach the dust cover to the roof section (29). Find the door handle and disassemble (30). Reattach the door handle

to the holes located in the glass door. Note: Tighten screws until they are snug, but not overly tight (31). Find the two

door hinges and hex wrench and disassemble the hinges (32).

Reattach the hinges to the door, tightening with the hex wrench so they are snug. Note: You may have to loosen the

screws again when the door is attached to adjust the t of the door. Once the t is completed you may tighten the

to the wall of the sauna with mounting screws, with the bottom of the heater being approximately 7” from the oor

of the sauna. Be sure that the screws are at the same height (37). Lower the heater onto the mounting screws (38).

Assemble the heater fence (39). Place the heater fence in front of the traditional heater (40).

WARNING: Never operate the infrared heaters and the traditional heaters at the same time. Operate one or the

other, depending on the type of sauna you would like to enjoy.

Power On/O

Turn on the system by pushing and holding the Power button for 4 seconds until the green lights on the display are

To adjust the temperature, press the Temperature (-) or Temperature (+) to raise or lower the set temperature. The

temperature is displayed in Celsius, with the lowest temperature setting being 30°C (86°F) and the maximum

temperature setting being 70°C (158°F). Pressing the temperature buttons will raise or lower the temperature by 1°

each time the button is pressed. After 8 seconds the display will indicate the actual temperature in the sauna.

The heaters can operate to a maximum of 60 minutes, and you can adjust the heating time with the Time (-) or Time

(+) buttons. You will add 1 minute to the time each time you press the Time button. After 8 seconds the display will

show the time remaining. When there are 5 minutes left in the cycle the timer will sound 3 times to remind you that

your session is ending. When the heaters turn o after 60 minutes you can reset the timer if you wish to keep the

heaters on for another cycle.

Bluetooth Function