N13275
Customer Helpline
NZ: 0800 422 274
N13275
INSTRUCTION MANUAL
Model Number : ETA-22D
Steam Iron
1
Important safety instructions
Store this instruction manual in a safe place, along with your purchase receipt and
packaging box for future reference. Please pay particular attention to the safety
information.
- This appliance is not intended for use persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Young children should be supervised to ensure that they do not play with
the appliance.
- Use this appliance as intended and described in the instruction manual only.
- Always unplug the appliance immediately after use.
- This appliance should never be left unattended when plugged in.
- Do not wrap the cord around the appliance.
- If the appliance stops unexpectedly, switch off the power supply, and unplug from
the wall socket. Contact the manufacturer or an authorized service representative.
- Switch off the power supply and unplug from the wall when not in use, before
cleaning and or changing accessories.
- Keep the appliance and cable away from sources of heat, sharp objects or anything
that may cause damage.
- Do not operate this appliance if the cable or plug is damaged. Contact the
manufacturer or an authorized service representative.
- Electrical appliances must always be stored in a secure place and out of reach
from children.
- Always ensure that your hands are dry before operating or adjusting any switches
on the product or touching the plug and main power connection.
- Do not leave the appliance unattended when connected to the main power supply.
- Do not use outdoors. This appliance has been designed for domestic indoor use only.
- Only use the power adapter that has been supplied by the manufacturer.
- To avoid the risk of electric shock, do not disassemble or attempt to repair the unit.
- Do not overload electrical outlet. Use only the power adaptor provided.
- Do not leave packaging components (plastic bags, cardboard, polystyrene, etc.)
within the reach of children, as it could be dangerous.
- Switch off and unplug when not in use, during filling of the water reservoir and
before cleaning the appliance.
- Designed for domestic in-door use only. Keep the iron casing, cable and plug dry.
- DO NOT IMMERSE IN WATER.
- Do not pull on cable to disconnect from mains supply.
- Do not operate the iron if it is dropped, leaking, shows signs of damage or if it
malfunctions. The supply cord cannot be replaced. If the cord is damaged the
appliance should be scrapped.
- If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent in order to avoid a hazard.
2
Knowing your Steam Iron
1. Sole plate
2. Housing
3. Water reservoir
4. Temperature control knob
5. Temperature indicator lamp
6. Heel
7. Mains cable
CAUTION
- The iron must be used and rested on a stable and flat surface.
- Do not cover the appliance and allow to cool fully before storing.
- The sole plate of the iron will become hot during use. Do not touch and always
carry by the handle.
- Do not use iron on, near or under flammable or heat sensitive items.
- Do not leave iron unattended while it is connected to the mains supply.
8. Handle
9. Steam burst button
10. Water spray button
11. Steam control knob
12. Filling aperture
13. Spray nozzle
14. Water beaker (not shown)
1
2
3
4
5
6
7
8
9
10
11
12
13
3
1. Remove the plastic protective cover from the sole plate of the iron and clean with a
soft, damp cloth.
2. Select the ironing temperature for the desired (as instructed by the manufacturers
instructions) item being pressed and align the corresponding fabric type marked on
the temperature control knob, with the arrow marked on the housing (just in front of
the knob).
3. If using steam, place the iron onto the sole plate and fill the water reservoir through
the filling aperture using the measuring beaker provided. Do not overfill or exceed
the MAX water level marked on the water reservoir.
4. Stand the iron in the upright position (resting on its heel).
5. Fully unwind the cable, plug in and switch on. The temperature indicator lamp will
illuminate to show that the iron is heating up.
6. When the indicator lamp goes out, the iron has reached the selected temperature.
7. If using steam, turn the steam control knob to the setting in the table below.
8. The iron can be turned off any time by switching off at the mains and unplugging.
CAUTION
- Some parts of the iron may have residual oil from the manufacturing process and
may smoke slightly on first use. Always test the iron before use on an old piece of
fabric to ensure that the sole plate is clean.
- Stubborn creases may be removed by using an additional burst of steam or by
using the water spray feature (press their respective buttons).
- This iron is suitable for use with tap water. If the water in your area is particularly
hard then it is advisable to use distilled or demineralized water.
- The steam function can only be used at the higher ironing temperatures.
Using your Steam Iron
- Stand the iron in the upright position (resting on its heel), switch off, unplug and
allow to cool slightly.
- Place the iron onto the sole plate and using the measuring beaker provided, fill the
reservoir through the filling aperture. Do not overfill or exceed the MAX water level
marked on the water reservoir.
- Stand the iron in the upright position, plug in, switch on and allow the iron to come
back up to temperature before selecting the steam setting.
Refilling the Steam Iron
4
Ironing Temperatures Guide
Instructions on
textile label
Fibre type
Temp
control
Steam
control
Synthetic
(eg Acrylic, Acetate, Viscose
(Rayon) Polyamide (Nylon), Polyester)
Silk
No steam
Wool
No steam
Cotton
Steam
Linen
MAX
Do not iron
It is important to ‘self clean’ the iron on a regular basis to remove any scale.
1. Fill the iron half full with water and stand it in the upright position.
2. Set the temperature control to MAX, plug into a kitchen socket and switch on.
3. Allow the iron to reach the maximum temperature before switching off and
removing the plug from the socket.
4. Take the iron to the sink and hold in a horizontal position over the sink.
5. Turn the steam control knob to self-clean ( ). The knob will pop up slightly and
lift out and remove the steam control knob.
6. Hot water and steam will now come out of the steam holes in the sole plate
washing out impurities and scale.
7. When water reservoir is empty, replace the steam control knob and move to the no
steam position.
8. Allow the iron to cool completely before removing residues on the sole plate with a
soft cloth soaked in a vinegar / water solution.
9. The iron housing can be cleaned with a soft damp cloth and then wiped dry. Do not
use detergent or abrasives as these may scratch the surface.
NOTE: Do not put vinegar or other descaling solutions into the water reservoir.
Storing your Steam Iron
- Switch off and unplug the iron.
- Empty any water remaining in the water reservoir into the sink.
- Stand the iron in the upright position and allow the iron to cool completely before
storing, in a cool and safe place.
Cleaning your Steam Iron
5
Note:
6
Note:
Warranty
Here at Cascade we pride ourselves on producing a range
of quality home appliances that are both packed with features
and completely reliable. We are so confident in our
products we back them up with a full 2 year replacement
warranty. Now you too can relax knowing that Cascade
have you covered.
Customer Helpline: 0800 422 274
This Product is covered by a 2 year replacement warranty when
accompanied by proof of purchase
/
