2. Raychem
  3. TOUCH 1500

Raychem TOUCH 1500 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Raychem TOUCH 1500 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
DESCRIPTION
The Touch 1500-HAZ nVent RAYCHEM is a panel mounted touch screen
display used in conjunction with RAYCHEM NGC-40 and NGC-20 (Europe
only) control and monitoring devices. The Touch 1500-HAZ display is rated
NEMA 4X (IP65) and can be mounted indoors or outdoors in a hazardous
location. For outdoor installation, a space heater will be required in the panel
for low ambient conditions. The Touch 1500-HAZ kit includes all hardware
required for mounting in a suitable electrical panel. Additional materials are
required for electrical connections and are detailed below. These instructions
describe how to mount the Touch 1500-HAZ in an electrical panel and are
intended only for personnel experienced in panel construction.
TOOLS REQUIRED
• Metalle • Maskingtape
• Phillips screwdriver • #16 (3/16) drill bit
• Jig saw (recommend using carbon steel blade with 24TPI)
ADDITIONAL MATERIALS (TO BE ORDERED SEPARATELY)
Qty Catalog number Description Mfg Mfg/
PTM PN
1 Touch 1500-HAZ-TS Touch Screen TTC 10332-011
1 Touch 1500-HAZ-CPU Computer TTC 10332-010
1 Touch 1500-HAZ-CK Cables/Mounting Hardware:
4-ft USB A/B Cable
4-ft VGA Cable
Touchscreen Mounting Clips
(1) 8-ft DB9 to RS-485 Cable
TTC 10332-027
1 ADAM-4069-C1D2 Alarm Module Advantech
1 Push-to-Test Alarm Light (24 Vdc)
APPROVALS / CERTIFICATIONS
Hazardous Locations
ClassI,Division2  GroupsA,B,C,D
40JY
I.T.E. for use
in Hazardous
Locations
Touch 1500-HAZ-CPU
23BJ
I.T.E.
Hazardous location
designation
Class I, Division 2
Groups A, B, C, D, T5
Hazardous Locations
I.T.E. for use
in Hazardous
Locations
316N/23BJ
Hazardous location
designation
Class I, Division 2
Groups A, B, C, D, T4A
Hazardous Locations
Touch 1500-HAZ-TS
TOUCH 1500
User Interface Terminal for RAYCHEM NGC Systems Installation Instructions
Touch 1500-HAZ-CPU and
Touch 1500-HAZ-TS
installed in a panel
The TOUCH 1500 is an electronic unit. During installation,
take the following precautions to avoid damage to its
electronic components.
• Handle with care to avoid mechanical damage.
• Keep electronics dry.
• Avoid exposure to static electricity.
• Avoidcontaminationwithmetallings,liquids,or
other foreign matter.
• Use agency-approved conduit bushings, adapters,
and cable glands to keep the enclosure protected
fromdustanduids.
WARNING:
General
Area of use Nonhazardous or hazardous locations, indoor or
outdoor (Type 4X, IP66)
Supply voltage Touch 1500-HAZ-CPU: 10 – 36 Vdc
Touch 1500-HAZ-TS: 19 – 30 Vdc
Amperage rating Touch 1500-HAZ-CPU: 2 A @ 24 Vdc
Touch 1500-HAZ-TS: 2.62 A @ 24 Vdc
Operating temp (CE)* Touch 1500-HAZ-CPU: –20°C to 60°C (–4°F to 140°F)
Touch 1500-HAZ-TS: –20°C to 60°C (–4°F to 140°F)
Operating temp (UL)* Touch 1500-HAZ-CPU: –10°C to 60°C (14°F to 140°F)
Touch 1500-HAZ-TS: 0°C to 50°C (32°F to 122°F)
Storage temperature –30°C to 80°C (–22°F to 176°F)
Dimensions (W x D x H) Touch 1500-HAZ-CPU: 85.5 x 139 x 152 mm
(3.4 x 5.5 x 6 in)
Touch 1500-HAZ-TS: 422 x 68 x 338 mm
(16.61 x 2.68 x 13.31 in)
Alarm Outputs
Relay output One Form C relay rated 3 A @ 250 Vac.
Relay is used as a common alarm.
* Note: Temperature ratings are without space heaters
Network Connection
Remote Port(com 3) Connects to common alarm module (ADAM-4069)
RS-485 A non-insulated 9 pin D sub male
Data rate To 9600 to 57000 baud
Field Port(com 4) Not used
RS-485 A non-insulated 9 pin D sub male
Data rate To 9600 baud
LAN 10/100 Base-T Ethernet port with Link
and Activity Status LEDs (X3)
USB Ports USB 2.0 host ports (X4)
LCD Display
Display LCD is a 15-in XGA, color TFT
transflective device with integral LED
backlighting.
Touch Screen 5-wire resistive touch screen interface
with enhanced ITO film for user entry.
2 | nVent.com
1. Provide suitable panel enclosure
To protect its electronic components, the Touch 1500-HAZ
must be mounted in a non-hazardous location panel with a
minimum of IP32 (NEMA 1) enclosure or hazardous location
panel with a minimum IP65 (NEMA 4) enclosure. The Touch
1500 assembly comes with a sealing gasket and hardware to
mount the touchscreen.
Note: The RAYCHEM Touch 1500-HAZ is designed for
operation in ambient temperatures from 0°C to 50°C (32°F
to 122°F). If the ambient temperature is outside this range, a
space heater with screen window kit and/or cooling fan will
be required in the panel.
2. Determine locations for the Touch 1500-HAZ-TS and Touch
1500-HAZ-CPU assembly in the electrical panel
The Touch 1500-HAZ-TS should be located on the front of the
panel near eye level (for convenient viewing).
The Touch 1500-HAZ-CPU should be located on the sidewall
or backpan of the enclosure.
The Touch 1500-HAZ assembly is an electronic unit and must
not be located where it will be exposed to strong magnetic
fields or excessive vibration.
C1
CB19
CB17
CB15
CB13
CB3
CB9
CB11
CB7
CB5
CB1
CB16
CB42
CB20
CB18
CB4
CB14
CB12
CB10
CB8
CB6
CB2
C2 C3 C4 C5 C6 C7 C8 C9 C10
CB23
CB25
CB27
CB29
CB21
CB26
CB28
CB30
CB22
CB24
CB31
CB33
CB35
CB37
CB39 CB40
CB36
CB32
CB34
CB38
1
3
5
7
9
19
17
15
13
11
29
27
25
23
21
39
37
35
33
31
2
4
6
8
10
12
14
16
18
20
30
28
26
24
22
32
34
36
38
40
PanelTouch 1500-HAZ
assembly location
Panel
door
Touchscreen
alarm
light
Panel
alarm
light
Provide Suitable Panel Enclosure, and Determine Locations for TOUCH 1500-HAZ Assembly in Panel
nVent.com | 3
1. Locate the TOUCH 1500-HAZ on the front of panel
Locate the Touch 1500-HAZ assembly ion the front of the
panel at the level convenient for viewing. Make sure the cover
on the back of the assembly will not interfere with existing
panel hardware.
Cutting
Area
Panel Door
396 mm
15.59 in.
296 mm
11.65 in.
Note: Cutting the opening for the display is a craft sensitive
procedure; if it is not done correctly, the panel door can
be damaged. The procedure for laying out and cutting the
opening for the display must be undertaken with care and by
personnel qualified and experienced in panel construction.
2. Prepare and mark the position of the display opening and
mounting holes
• Use the cut-out directions to lay out the opening for the
Touch 1500-HAZ-TS.
• Apply two layers of masking tape around the outer
perimeter of the intended opening to prevent scratching
the panel surface with the jigsaw.
3. Cut the display opening
Cut the opening for the Touch 1500-HAZ-TS with a jigsaw
using a 24 TPI blade. Take care not to damage the panel door.
Remove all rough edges and burrs with a metal file before
proceeding.
Note: The following steps are most easily accomplished if the
panel door is on a horizontal surface.
4. Mount the user interface assembly on the panel door
• Place the Touch 1500-HAZ-TS assembly in position.
Secure the screen to the enclosure with the 10 mounting
clips.
Panel door
TOUCH 1500 display
with sealing gasket
Inside of
panel door
TOUCH 1500 display
• Place the supplied mounting clips in each slot along the
sides of the Touch 1500-HAZ-TS. Only fasten hand tight.
TOUCH 1500 display
Mounting clips
• Look at the front of the panel, and align the Touch
1500-HAZ-TS assembly so it is level (loosen clips if
necessary to reposition the assembly).
• After the display is properly positioned, tighten the mounting
clips. Do not overtighten and risk damage to hardware.
Cut Opening and Mount TOUCH 1500-HAZ on Front of Panel
4 | nVent.com
296 mm
(11.65 in)
Panel Cut Out Area
Top of Display
Drawing
NOT TO SCALE
Drawing
NOT TO SCALE
396 mm
(15.59 in)
Panel Cut Out
Panel Cut Out
TOUCH 1500 Cut Out Dimensions
nVent.com | 5
USB-B Touchscreen
interface to CPU
VGA Touchscreen
interface to CPU
Not usedNot used Incoming
power
VGA (display)
CPU to
touchscreen
interface
USB
ports
(X2)
USB ports (X2)
Not used
COM3
RS-485
Remote
Port
COM4
RS-485
Field
Port
COM3
RS-232/422/485
USB
VGA
USBUSB
LAN2 AUDIO
MIC
PWR
LINE-OUT LINE-L
LAN1
LAN3
COM4
RS-232/422/485
TX1 RX1 TX2 RX2
CF R.BTRB.BTRTEMP.V OLT .
Ethernet
ports (X3)
RL4NO
RL4COM
RL3NO
RL3COM
RL2NC
RL2COM
RL2NC
RL1NC
RL1COM
RL1NO
RL0NC
RL0COM
RL0NO
RL5NO
RL5COM
RL6NO
RL6COM
RL7NC
RL7COM
RL7NC
NC
INT+
(Y) DATA +
(G) DATA –
(R) +Vs
(B) GND 10
ADAM-4069
Relay Output
Module
8 Outputs
Optional mouse/
keyboard input
Power switch
Not used
Incoming
power
Touch 1500-HAZ-TS Port Diagram
Touch 1500-HAZ-CPU Port Diagram (Back view)
ADAM-4069 Pin Diagram
Touch 1500-HAZ-CPU Port Diagram (Side view)
6 | nVent.com
Connect Power
Connect 24 Vdc to the connection fittings to the Touch 1500-HAZ-CPU, Touch 1500-HAZ-TS, ADAM-4069 module, and ADAM-4510I
modules per the schematic on the following pages.
Phoenix Power Supply
QUINT-PS-100-240AC/24DC/10EX
100 – 240 Vac
50/60 Hz
Line Neutral
14
DC
OK
+ + – –
L N
INPUT
AC 100-240V
Output DC 24V 10A
13
Terminal
block
Terminal
block
Terminal
block
Terminal blocks
RL4NO
RL4COM
RL3NO
RL3COM
RL2NC
RL2COM
RL2NC
RL1NC
RL1COM
RL1NO
RL0NC
RL0COM
RL0NO
RL5NO
RL5COM
RL6NO
RL6COM
RL7NC
RL7COM
RL7NC
NC
INT+
(Y) DATA +
(G) DATA –
(R) +Vs
(B) GND 10
ADAM-4069
Relay Output
Module
8 Outputs
+
+24 Vdc
–
Terminal block Terminal block
Terminal block
2
1
Alarm
Lamp
24 V Lamp
Idec Switch/Lamp
4
3
Alarm Lamp
nVent.com | 7
+
+24 Vdc
–
+
+24 Vdc
–
Terminal block Terminal block
Terminal block Terminal block
Touch 1500-HAZ-CPU
Touch 1500-HAZ-TS
G – +
Power switch
Not used
Incoming
power
G – +
USB-B
TS interface
Not
used
Not
used
VGA Touchscreen
interface to CPU
Incoming power
8 | nVent.com
Field Port Communication RS-485 Common Alarm Light and Alarm Relay
Mount the supplied ADAM-4069 modules on a DIN rail inside the panel enclosure. Mount the alarm lights on the panel’s door below
the touch screen.
Wire per the schematic below.
VGAUSB
USB cable
VGA cable
VGA
USB
COMM 3
Custom 9 pin RS-485 cable
RL4NO
RL4COM
RL3NO
RL3COM
RL2NC
RL2COM
RL2NC
RL1NC
RL1COM
RL1NO
RL0NC
RL0COM
RL0NO
RL5NO
RL5COM
RL6NO
RL6COM
RL7NC
RL7COM
RL7NC
NC
INT+
(Y) DATA +
(G) DATA –
(R) +Vs
(B) GND 10
ADAM-4069
Relay Output
Module
8 Outputs
MIC
PWR
LINE-OUT LINE-L
TX1 RX1 TX2 RX2
CF R.BTRB.BTRTEMP.VO LT.
To Alarm Lamp on Panel Door
Touch 1500-HAZ-CPU
Touch 1500-HAZ-TS
RL5NO
RL5COM
RL6NO
RL6COM
RL7NC
RL7COM
RL7NC
NC
INT+
(Y) DATA +
(G) DATA –
(R) +Vs
(B) GND 10
nVent.com | 9
Servicing
The Touch 1500-HAZ-CPU and Touch 1500-HAZ-TS contains no user-serviceable parts. Contact your nVent representative for service
and an authorization number if required.
Cleaning
The touchscreen are of the Touch 1500-HAZ-TS may be cleaned with a damp or dry cloth. Typical window cleaning agents may be
applied to aid in the removal of dirt, dust and grease. Do not use abrasive cleaners.
North America
Tel +1.800.545.6258
Fax +1.800.527.5703
[email protected]
Europe, Middle East, Africa
Tel +32.16.213.511
Fax +32.16.213.604
[email protected]
Asia Pacific
Tel +86.21.2412.1688
Fax +86.21.5426.3167
[email protected]
Latin America
Tel +1.713.868.4800
Fax +1.713.868.2333
[email protected]
©2018 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its aliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specications without notice.
Raychem-IM-H58823-Touch1500HAZ-GB-1805
nVent.com
/