ZGG24L20BSS

GE ZGG24L20BSS Installation guide

  • Hello! I am an AI chatbot trained to assist you with the GE ZGG24L20BSS Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
GE Monogram ®
24" Outdoor
Cooking Center
MOdal
Z(.(.24I,
Before you begin-- Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector's use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference.
If you received a damaged cooking center, you should
contact your dealer.
Insta!latian of this cooking center requires basic
mechanica! skills. Proper installation is the responsibility
of the installer.
ForMonegram local service in veur area,
1=800-444-!845,
ForMueagram service in Caeada,!-888-880-3030.
ForMonogram Partsand Accessories, call
1=800-626-2002.
Inthe gommonwealtl_ of Massachusetts:
This product must be installed by a licensed
plumber or gasfitter.
When using bailtype gas shut off valves, they
shall be T-handletype.
oA flexible gas connector, when used, must not
exceed 3 feet.
FORYOURSAFETY:
Do not usecooking center in a space where gasoline or
other liquids havingflammable vapors are stored or
used=
[FYOU SMELL GAS:
Shut off gas to appliance.
Extinguish any open flame.
Open lid.
if odor continues, immediately call ,/our gas supplier.
CAUTION:
For outdoor use only. Use this cooking center only in
the manner intended by the manufacturer.
This outdoor cooking gas appliance is not intended to
be installed in or on recreational vehicles and/or
boats.
®Do not use the grill in an explosive atmosphere. Keep
the grill away from areas where gasoline or other
flammable liquids and vapors are stored or being used.
®Observe proper clearances to combustible materials at
all times.
Do not use a rusty or damaged LPtank.
Never substitute gases (natural for LP or LP for
natural).
®This grill is factory set for liquid propane gas. A natural
gas conversion kit must be installed before using
natura! gas.
®When storing the grill indoors, disconnect the LP tank.
Store the tank outdoors in a well ventilated area.
Do not store additional LP tanks in or near the gas grill.
Follow the guidelines on the LP tank for proper storage,
transport and handling.
®Tested in accordance wkh ANSI Z21.58 latest edition
standard for outdoor cooking gas appliances. This grill
is for outdoor use only. Check local building codesfor
the proper methodof installation in the absence of local
codes,this unit should beinstalled in accordance with
the National Fue!GasCode No.Z223latest edition and
the National Electrical CodeANSI/NFPA No.70-19%
CALiFORNiA PROPOSiTiON 65 -WARNING
The burning of gas cooking fue! generates some by
products that are on the list of substances which are
known by the State of California to cause cancer or
reproductive harm. California law requires businesses to
warn custorners of potential exposure to such
substances. To minimize exposure to these substances,
always operate this unit according to the use and care
manual, ensuring you provide good ventilation when
cooking with gas.
INSECT WARM N6[
Spiders and insects can nest in the burners of this and
any other grill, and cause the gas to flow from the front of
the burner. This is a very dangerous condition which can
cause a fire to occur behind the valve panel, thereby
damaging the grill and making it unsafe to operate.
Inspect the grill twice a year or immediately if an,/
symptoms appear.
Desiga [efarmatiee
Model ................................................................................. 3
Product Dimensions & Clearances .............................. 3
Accessories ...................................................................... 3
Advance Planning ............................................................ 3
Choosing the Location .................................................... 4
Tools & Materials Required ........................................... 4
Step 1: Remove the Packaging ..................................... 4
Step 2: Provide Support,
Insta!lation on a Cart ......................................... 4
[estallatiee
Step 2: Provide Support,
Built-in installations .......................................... 5
Step 3: Provide Gas & E[ectrica! Supply ..................... 6
Step 4: Test for Leaks ...................................................... 7
Step 5: Lighting the Grill .................................................. 7
Step 6: Adiusting the Burners ....................................... 8
Finalize Installation .......................................................... 9
install Rotisserie .............................................................. 9
ZXADYSS, ZXSDBSS, Optional Access Doors ........... 9
ZX24NGB, Natural Gas Conversion Kit ...................... 10
Design In%rmathm
24" O_ddoo*' Cookh_g"(.'e,ter
Modal
Pro&tct
Di me'++sio'Y+,s
ZGG24120 SS
The Monogram 24" ()indoor" Cooking (_ente1"
is f_( to_'v set R)_"LP gas and can be convex'ted
to natm'a] gas. O_'de_"ZX24N (;B Natm'a] gas
conve_'si on k]t _hen n at m'a] gas is ava]]ab] e.
24-3/4"
0
24" (Cutout)
9"
"12" Min. to Combustibles
4" Min. for Lid Clearance
Manifold
Pipe 34/2"
_4" ForLid Clearancewhen installed
into a non-combustibleenclosure,
Allow 12"rain clearance to
combustible vertical surfaces.
Advance
This g_il] may be h]stalled on a pox'table g_il]
cm't oi" bllih into an e]]ch)sm'e.
Endosmes ca]] be consti'ucted o{ non-combus-
tible (mnsom'y) mnte1"ia] oi" of combustible
material such as _oo(L Insulated jackets a_'e
_'e(pfi_'ed fo_" h_stallation into combustible
e_] c] osHI"es.
* ZX24CTBSS, grill can't
" ZX24JBSS_]nsl_lated jacket J_b_"a combustible
en closm'e.
o ZX24TKBSS is _wai]ab]e to conceal the gap
betwee]] the cook] m]_.{cen te_" m]d the
eli c] osm'e.
* ZX24CV'C_ tol_gh vinyl on the oms]de_ felt
]im]ed im]shie with elastic to hold the cove_" hi
place. Fits g_'ill i_stalled on a cm't o_" M_en
b_fi]t-in,
* ZXS])BSS - Stai_]]ess Steel Single Access Doo_"
ZXADYSS - Stahi]ese Steel Dol_b]e Access
Door's- Optional at cesso_'ies to cove_" the
access openh_g m_de_" the g_il] in a b_fih-in
in sta]]atiom
* ZXI J_Y;IJ _ gas ta_k.
* This Monog_'am Outdoor" C_ooking Center" is
desig_led to be h_stalled on a g_ill cm't o_" hm)
;m e_]closm'e.
* h_ a mm-comb_,st]b]e (mas(m_'y) e_]c]osm'e_
the g_'i]](h'ope into the opening. A ]edge on
each side is _'eqld_'ed ibm" s_qq_<>rt.
A]] h]su]atedjacket is available to a]]o_ the
g_']]] to be i_]sta]]ed in a combustible
eli c] osm'e. The hi s_]ated,ja( ket m _st be
suppo_'ted by a ]edge o]] each side.
* If _si n g a backsp]ash o_" _'ea_" _ a]], locate the
electrical se_'vice fb_" the _'otisse_ie on the
_'igh t s] de.
* T_'] m kit ZX24TKBSS is awfi]ab] e to con cea]
the gap bet_een cook]_]___ tel'item" mid the bark
a_] d s]des of m] eli c] osm'e.
C_ea!oances
* Allo_ 4" at the _'em" fkn" lh] cleam_]ce.
* Allo_ at least 12" cleam_]ce at the back of the
g_'ill whe_] exha_st is dh'ected to a wi_]dow o_"
a sin'{hoe that is diil]c_*h to c]eam
* A]]o_ at least 6" c]em'm]ce ()1] each side to
an]v non-combustible matelia] Mcated above
the cooking sm'ihce %_" com]te_'space. This 6"
cl era'an ce _ ill all o_ }b_" placem en t an d
h a_] d]h] g of the _'ot] see_'i e m o to_" a_] d sk,e_ e_'.
* A]]o_ at least 12" c]em'm]ce ()1] ea(h side and
] 2" m hi. c] era'an ce at _'em" to corn b_ st] b]e
ve_'ti ca] mate_'ia]s.
Desigl_ I1Kbrmatkm
24" Outdoor Cookin£ (/e_/ter
CTtoosir_,g
the Locatio'n
* This cooki_lg cem]ter is designed for ol_tdoor
use on]v. Do not locate the grill in a
building, garage or other endosed area.
* En slate th at {}'esh air ve_ ti]ati o_ is adeq Irate.
* ( onsider exposure to _qnd and proxh_ity to
* The clearances to combustib]es
m'N?llstbe maim]taimled at air times.
* Do m)t h]sta]] a gr]]] be]o_ overhead
m_protected combllstib]e co]/struction.
* The installatio_ midst conform to local codes
or h_ the abse_ce of local codes, with the
national fuel gas code, ANSI Z223 latest
edition.
7bets
* Phillips head scre_driver
* Pipe _ ten ch
* I _eve]
* Fiat blade screv, driver (3/32" blade)
*P]iers
St@ l
Remove the
Pa&(_#i'n,g
* Open the box and remove packaging.
* Opel] the gr'i]] rid and r'emo_,e ]_ardv, ar'e
accessor_ car'ton. CJ/eck c(mte]]ts.
Motor
2 Grill Grates
St@2
Provide
Spit Forks
2 CeramicBricluetteTrays
RotisserieRodandHandle
LPRegulator
The Ol_tdoor C(_okim_g (}enter can be h_sta]]ed
on a ZX24CTBSS cart M_ich is desig_ed
specifically fin" this mode]. Fo]]o_ the i_]sta]]a-
tio_] h]structio_s provided _ith the cart to
i_sta]L Proceed to Gas s_app]?, Step 3, to
complete the i_sta]]ation.
Type1Acme,
20 Lb LPTankwith Overfill
Protection Device.(not supplied)
OrderZXLPY
Requiredfor Grill Cart Installation
*A]]ow at ]east 12" c]ear'a_ce at the back of the
gri]] _]]el] exhm_st is directed to a _in(]o_ of
a sm'JB/ce that is difticll]t to dean.
Ot_,a,(,a,'_t
Installation
24" Ou&Ioor Coohh_£" Ce_Her
Built@n,
T_ H S g_'H _ _ _;r _)e ira]stalled into a combustible
(w e]/dosm'e.
(_x)mbl_stible eudosm'es ]'eql_i]'e the i_se of am]
Cle_oances
TT
Allo_ 4 at the rear [o]" lkt dea]'ance.
* Allo_ at least 6" clearaN]ce on each side to
_H/V mlo]l-co])lbllgtig)le l))_teYi;_l located _bove
the cookim]_ sm'li_ce fl)r com]terspace_ T1]e 6"
clearam]ce ;_lhals fl_" placin£ and h;u_dling
ill e _x)t] sse_'i e m oto_" ;_m] d ske_,l e_'.
* A]hm _t least 12" c]earm]ce om] ea(b side mid
rear to combustible vertic;d m;_te_'i;ds.
Btdlt:{n
Acorn Nut- ' Right Side
ZX24T_SS _[¥im Kit
Thi s kit is awfi]ab] e flw m]on-corn blastib] e
enc]osm'es. The t_im _li]] conceal tile gap at
t]] e rear a_] d both si des of t]] e ope_]in g_
* Secm'e t_'im to tile sides and ba_k with sc_'ews
* _]ace the _ri]] iC_to the e]ldosm'e.
ZX24JBSS Insulated Jacket
The i_]s_flated,iad<et is req_fired fl)r combus-
due eudosm'es.
* b]sta]] ]eR a]] d rigb t si de pieces wi tb bolts
* Secm'e bolts d_],'d(]e the _]1]] _t]/ acoH] m_ts.
* h]sta]] ba_k pa_]e] to side pm]e]s. Place tile
grill i_to tile endosm'e.
4"Min.forLid
35-1/2
Max."
24-1/2"
If Installing
an Electrical
Outlet for
the Rotisserie
Motor, Mount
)n Right Side
.)
12"Min.to If Installingan
Combustibles ElectricalOutlet
4" Min. forLid 25-3/4" forthe Rotisserie
Motor, Mounton
RightSide
(6.5AMPMin.)
35-1/2
Max."
Openingfor
DoubleAccess
Doors
_nstallation in a non-combustible enclosure.
* 1]] a m_]]-combustib]e (masom'}) e]]c]osm'e_
the g]'i]] drops i_]to the ope]]b]_. A ]ed£e o_]
each side is required for support.
Openingfor
DoubleAccess
Doors
i[nstallatlon [n a combustible enclosure,
ZX24JBSS insulated jacket is required
* Cxm/tx_stibIe eucIosm'es req_fire ZX24JBSS
b]s_]atedjacket. The ]_]s_]ated,iad<et must
be supported by a ]ed£e o_] eac]] side_
(]o]]str_ct the e]]dosm'e ;_s sho_l]]. }{_]stall the
b]sul_ted j_cket o]]to the grill. Pl_(e the
cooki_]g center b]to the opening. No
h]sta]];_tio]] b;wdware is req_fire(].
h stallati<m
24" OuMoor <,'oo]_h_g<,'e_rte*'
Provide
(;as
NOTE: S/@ this st@ !/ )'o_ wish to c<mr_ed to
Hat?_'gd ,gzt,ssw'_/@'. ()rd_,r Z,X224NC!I kit. 1{_,/b'to
Nat_r(d (;as Omve_:sio_ h_sh'_ctio_s, /_ag_,10.
PRODiJCT STORAGE
LPHose
Pre-Attached
Coupler Sleeve
ve
* ( omlect the regl_]ator to the ql_ick
di scol] n ect ]1ose assemb]v.
* Check to be sm'e the main valve on] the I,P
To connect the tank:
* ]{nsert t]_e coupler sleeve over t]_e tmlk hl]et,
tur]] clockl_ise to tighten.
To diseon_met the tm_k:
* Tm'n off the main tan k valve.
* Grasp the coupler sleeve and ttu']/ comlter-
clockwise. Remove the h/]et t&>m the
o]oei] Jm/g.
I_P operating pressure is ]0" W.C.
IMPORTANT: The I,P tan k m ust be a Type ]
Acme. Do not attempt to change or alter these
slq_p]ied parts Do m]ot attempt to _se the
regulator/h ose assemb]y/_ ith a start dard 5 ]i0
POI, tank/w_]ve assembly.
EI ,ECTRICAI _S[ IPPI 5
The rotisserie reqtfres ] 20V, 6(}Hz., and
com]ected to an individtm] properly
groin]deal brm/ch ch'c_ft protected by a ]i5
amp circuit breaker or time delay fuse.
The po/_ er cord (>nt]] e rot] sseri e ]s eq ui pped
t_ith a th r ee-prol]g (gro un di n g p]ug/_ hi ch
mates/_it]] a standard three-prong grotmdi_]g
t_a]] receptacle to minimize the possibility of
shock hazard {}'ore this appliance.
If the electrical service provided does mtt
meet the above specifications, it is recoi/l-
m e_] de d t h at a ]i ceil se d el ectri cian h/stall an
approved om]et.
D O N OT [IN DER ANY CIRC [ IM STA N CES,
(;IJT OR REMOVE THE THIRD ((;RO[ IND)
PRONG FROM THE POWER (ORD.
* For b_f]t-in grill i_]sta]]atio_]s, locate the
el ectri ca] o inlet on the righ t h m/d side.
I stallati(m
24" Outdoor Cooking Center
Ste/ 4
e,%jo
Leaks
St@ 5
Lz ¢/ttir ¢
#te
TEST FOR I _EAKS
A complete gas tightm]ess check midst be
perMrmed at the installation site.
* Do not lase the grill m]ti] a]] c(mnections
have been leak tested.
* Repeat leak test a{}er ea(h I_P taM_ change.
* C_heck to be sm'e the maim/ wt]ve o]] the IJ -_
tin/k or th e sh IB.t-of} valve ]s ]FI th e "O FF"
position.
* Make a soap so] miom] of one part ]iqlfid
detergent an d o]]e part _ ater.
The valve pm]e] must be removed to check the
valves and fittings.
* A]] control valves shol_]d be in the "OFF"
* Remove the knobs.
- Rein ore the 4 scre_ s h o] di_'_g the valve pa_'_e]
to the grill (2 behind bm'ner knobs and t*ao
TO TEST:
* Apply the soap solution aromid the
com]ections, _t]ve a_]d tubing.
* Tm'n the gas supply on.
* CJ_eck a]] com]ections t_'om the supply ]h_e
or I_P tam]k IB.p to am/(] im/c]lB.(iim/g the maFdfi)]d
pipe assemb]v.
o If a leak is detected, mrn gas supply to off
mid tighten fittings. Tm'n the gas on mid
* P u]] the pan e] olltwards an d m]p] ug the _ ires
}}'ore the back of the rotary igni ters.
Do not attempt to
light the grill if the odor of gas is present.
1] _]e Imat pas essayer
d'a]hm_er ]e gri] s'i] v a m]e odem" de gaz.
* Open the rid.
* Tm'n a]] knobs to "OFF" positiom
* Tm'n gas supply on at the I,P tank or shut-off
valve.
NOTE: When lighting the b_.r_/er ti)r the first
time or a{_er a I_P tank chm]ge, allow _p to 20
sec(mds to purge air fl'om the ]h_es.
* Pus]] and tm'n control km_b to "I,ITE"
im m ediate]v tm'_ th e rotary ign] ter
]<_1]ob nex t to th e b III'11er ]<_1]oh.
NOTE: The spark will prod uce asn appi n g
so m_d. Th] s is n orm aL
* If the b_rn er does _ ot ]]gh t withh_ 4
see(rods, mrn knobs to "OFF" and _ait 5
mimates J_br the gas to dissipate before trying
* If the bur_] er does _]ot ]]gh t after several
attempts, the bm'ner can be lit _Gth a match.
TO MAF(H I_IGHT:
* Strike a match and hold over the match light
hole at the top ]eft side_ See illustration.
* Push and t_rn the control knob to "I,ITE".
Match
Hole
)-
WAlT 5 MIN []TES BEFORE REi _IGHTIN G A
HOT GR]I _I.
Installathm
24" Outdoor Coohh_ K Ce_ller
st@ 6
A4iustb ,g
the Bur_,e_:_
Adiustmems should m_t be required, re]less
qbration dmqm_g transit or _ariatiol]s im_h_cal
gas slq_pl) make m im_o_"adjl_stm en ts m_ecessm').
A({iustmems must be made by a qualified
tec hm_]cian at th e ti m e of ]m_stall ati om Ex trem e
care sh o u] d be used if a({j ustm en t s are made
aiter hi sta]]ation.
TO ADJUST:
* The l_dve pm]e] cover m_lst be l'emoved to
access the the air shmten Follo_ the
instnlctions in St_jt 4, 7)<st/br Lt'al_,s.
LockScrew
J
©
6rill Box
0
* i,ocate amid ]oosen the ]ock scl'e_l on the
fhce of the ah" s]m.ttel" _,;ith a scl'e_,; driver.
*Tm'n bm'nel" to the "I_ITE" positiom
* I_ th e I_]am e is yell o_l_ im]di cati m]g h] surf] ci en t
air_ ope_] the air sh utter to a]] o_l m ore air to
the bm'_] er.
* If the flame is nois/ mid tends to ]ift m_av
from the bm'ner_ thel'e is to<)much air. Tm'<]
the air shutter to reduce the ope<]hlg.
* ()]1 ce ac]j usted_ t m']] t h e burn er off m] d
reverse steps to l'e-install the valve panel
coveL
Low setting Adjustment:
Mhml" a(!iustments may be requh'ed due to
f] u ct tlati o_/s hi ]oca] gas pl'essm'e. A (!i_lstm e<]ts
to i_lcrease or decrease gas flow may be
_1ecessarw
* Tm'n bm'_ el" knob to "I _ITE" posi ti on.
* Tm'n tile contro] knob to tile ]o_lest setting_
a]] th e _,;a/' co m] ter-c] ock_a ise.
* Remove the knob bv p_fl]ing straight o_lt.
* In sert a thin-blade flat scre_l driver hi to the
l_dvesha{t and hold. (3/32" blade width
* (;rip the shaft xqth pliers and turn _ om]ter-
c]ock_qse to hmer tile flame, or c]ock_dse to
in crease the f]ame.
Always check tile hm
flame size for stabi]itv. A bm'_lel" flame
_hich is to<) small may go out of be extin-
guished easily. This can cause m]bm'ned
gas to escape a_]d cause a hazardo_ls
con dition.
h stallati<m
24" OuMoor Cool,'h_g <,'e_r*e*'
* Place the small ceramic br]qL(ette trnx at the
rear an d larger truly towards the fn'on t.
* Pla_e the grill grates over the open(rig.
Nete: Theceramicbriquettes may moveduring shippillg orwhen
repositioningfor rotisserie use. Forbest cooking performance,
slide briquettes onthetra:vso they are evenly spaced anddonot
block vent holes.
Rein ove b {u'm]er grates.
Rein ove t_'on t (large) ceram] c br] quette tray.
Place small ceramic briquette tray ]n the rear
sl OrS as sh {)v, ]1.
P]a_e drip pan o]] the grill floor mid agn]nst
the briquette tray.
Slide the motor dow]l ]c_to the chain(el ore(
the r]ght s(de.
To i(se, place pointed end of the skew1 er into
the motor, an](] the threaded end rest(rig o]]
the lelt side support.
Screw h m( dl e on to the th readed el( d of the
skew1 er.
Nete: %move motorwhen not in use.Store motor in dry place,
ZXAD YSS
(¢/n.d
ZXSDBS5'
ZXADYSS - Double Doors
The open(rig should be 24-1/8" _Hde and
ZXSDBSS - Single Doors
The openh_g shol(ld be 22" wide and 20" high.
* Place the fi'am e]m]to the open(rig an]d secm'e
_]th scre_ls on all sides.
e Hang the doors on the hinges as sho_l n.
Nat_rag Gas ConversionK_t
Parts supplied:
* Natm'al gas regulator
* Natm'al gas orifices
*Adapter 1/2" to 3/8" flare fkting
*T/_ o, ]/2" NPT close nipple
MateriaLs Required:
(not supplied)
* ]2 fi. to ]5 ft. max. []exib]e hose/_ith 3/8"
flare end (corrugated stah/]ess steel
* Pipe t_rench
* Pipe threadh]g compomld
* Mamm] gas sh m-off valve
* Appropriate ]ellgth of gas line to reach the
permanent installation location /_ith a 3/8"
flare end.
* Fiat blade scre/_ driver
Note: Optional ZX144HKYquick disconnecthosefor natural gas is
availableto reacha I44" connection
The grill mid its individual slmt-offvalve must
be disconnected [}'ore the gas supply during
any pressure testing o{ the system at test
pressures in excess of ]/2 PSIG.
The grill must be isolated fi'om the gas supply
svste F_]bv cl osi m/g its hi divi dual sh u t-off valve
durh/g rely pressure testin g of the svstem at
test pressures equal to or less than 1/2 PSK;.
The in sta]]ati oil of th]s grill must col/form
_ ith ]l)ca] codes i)_; h] the absence of local
codes, with the Natitma] fuel gas code, ANSI
Z223 latest edition, hlsta]]ation h] Canada
must be in accordance t_ith the Standard (AN
l-b] 49-1 and/or .2 (h/stallatio_] code Jtiw gas
burning appliances and equipment) and local
codes.
Operating pressm'e is 4" W.C.
Supply pressm'e s]]lm]d be 5" to ] 4" W_(]. 1[
pressure is more than 14" W.C. a step dog, m/
regulator is required.
Step l
lnsta22
l_ittin,<7:_'
R<q'uZator
]o
Check/_it]] local gas utility or l_ith local codes
tbr instructiims on h]sta]]im]g gas supply ]im]es.
Be sure to check im type amid size of mm mid
ho/_ deep to bm'v the ]h]e_ If tile gas ]hie is too
si'_ial], the grill /_il] not hmctiol] properly.
In stall a mall ua] gas sh m-off valve in an easily
accessible ]ocatiom
Iise threadh]g compom/d on m/ira-flare
fittim]gs only. DI)not use threadhlg compound
oil tile male end i)t the ]/2 NPT to 3/8 tlare
* Make coill]ecti ollsas sh ia_n.
* Rein ove q u]ck di scIm n ect h o se assemblv f]'om
manifl)ld pipe.
* I,em'e flare fitti ng h/ the man]ti)ld pipe (1/2"
to 3/8" flare).
*Atta(h installer supplied gas line to end oJt
flare fitting i)l/ the mamJti)ld.
* Install regulator to gas ]im/e.
* h/stall ]/2" NPT close nipple to supplier
im]stall ed sh m-off valve.
* (:beck to be sm'e the regulator arrow points
in the direction otgas flol_, to/_ards the grill
an d :may from the gas supply.
Installer.
Supplied
TUBING
(3/8"FLARE)
Adapter1/
to3/8" FlareFitting
1/2 NPTCloseNi
Gas4.g" Regulator
Nipple
_pplied
Shut-Off
-NaturalGasSupply
"qaturag Gas Conversion Kil
()pem_ the hd.
Rein ove racks m]d briq I_ette trays.
Remove bm']]er knobs mid 4 scre_s o]] the
_lve panel (2 scre_s behind knobs :rod
2 scre_ s be] o_ valve pm] el ).
]]{t the com]tro] pane] iq_ mid mid tilt bad<
mu4' fi'om the grill.
Discom]ect 2 ignitor wires.
Remove comro] panel
PItH bm']]ers ba(k mid ;_'aav fi'om the orifices.
Remove orighm] orifices, one on each side_
Apply threadh]g compom]d to new orifices,
h]sta]] mid tightem
R e-p os] ti o n burm] er in si de th e grill m]d w] t h
air sh utter en (is coverh]g the orifi ces.
(beck air s]mtter, the s]mtter shol_]d be
open approximately 5/] 6".
O
GrillBox
st@3
/o "
Leaks
\"ERIFI(;ATION
DES FI J[TES
1[1fmlt v&rifier qlle ]'installation n'a mtclme
flfite de gaz.
Do m/or o.se the grill m/ti] a]] c]nmecti]ms
have been leak tested.
* Check to be sm'e that the sitar-off \:_]ve is hi
the "OFF position.
e I]] a spray bottle, make a soap so]Ht]o]] of
o_1 e part ]i qlfi d detergent m] d on e part _ at er.
TO TEST:
* Spray the soap sol mion arom]d the
com]ectio]]s, _;_]ve and robing.
* Tm']] the gns slq0p]y (m.
* (2h eck a]] con m]ecti]m s J@om the gas supply
limle lip to and im]c]l_(iing the mam]ifi)]d.
* If a leak is detected, mrn gas supply off and
tigh ten i] tti rigs. Tm']] the gas on an d cbeck
st@ 4
Adjust the
_Zt YY_,e)%
LockScrew
o
Grill Box
o
] I
Note: While performing installations described in this book,
safety glasses or goggles should beworn,
t_n ,_,li_tzo£'r_nf lo_'M _n, _ _t_yol_r __, _'MI
1-,_00-444-1,245.
Not@: ])loduc[ b11_['(£_- 1]](11[ Js _1 (:OH[[HUiII_ CHd__41"_OF _1[
( (H_rd I{l_ctric. Th_r([;)r_, materials, al>p(manc_ md
sp(cificafions ire subj_c_ to ch;m_( will]out noti{:(.
PuL No.49-8966-2
Dwg.No.164D3333P193
PrintedinUSA
(ND 728) 3/03
10905-Rev2
Monogram:
½9bringgoodthingstolife.
GEConsumer Produc_s
General E/ecnic Company
Louisville, KY 4f1225
4 200,?General Electric Company
/