Honeywell HE420A User manual

Brand: Honeywell

Model: HE420A

Type: User manual

INSTALLATION INSTRUCTIONS

69-1108-2

READ AND SAVE THESE INSTRUCTIONS

HE420A Steam Power Humidifier

APPLICATION

The HE420A Steam Power Humidifier uses a thermal fan

interlock control to provide humidification for the whole

house. The steam power humidifier is designed to work

with high efficiency furnaces and heat pumps.

INSTALLATION

IMPORTANT

This product is for residential applications only

and must be installed by a qualified HVAC con-

tractor. Failure to comply could invalidate the

product warranty, or result in serious injury or

electrocution.

SELECT LOCATION AND MOUNT

WARNING

Electrocution, Heavy Equipment and

Chemical Hazard.

Can cause death, blindness, water damage to

home and heater failure.

• Do not cut into any air conditioning or

electrical line.

• Wear safety glasses when cutting or drilling.

• Mount the humidifier in a level position to

avoid water damage and heater failure.

• Reinforce duct as necessary to ensure

stability.

There are three typical ways of mounting the steam

humidifier. See Fig. 1, 2, and 3. Be sure to select a

location where the humidifier can be plugged in without

an extension cord. The preferred installation location is

on the warm air side of the furnace. If that location is not

possible, the humidifier should be mounted a minimum of

6 ft (1.8m) upstream from the furnace filter. Depending

on the location selected, additional duct reinforcement

may be necessary because the humidifier weighs 18 lb

when filled with water.

Fig. 1. Mount humidifier horizontally under duct

using mounting bracket.

Fig. 2. Mount humidifier horizontally under duct.

M10536B

IFIE

IFICATEU

M10578B

IFIER

MIDIFICATEU

HE420A STEAM POWER HUMIDIFIER

69-1108—2 2

Fig. 3. Mount humidifier horizontally under duct

extension using mounting bracket.

CAUTION

Steam Condensation, Fire and Freezing Water

Hazard.

Can cause failure of fan or limit control or

result in water damage to home.

• Do not install the humidifier where the

sidewalls of the return air duct are constructed

of wood (i.e. floor joist).

• Do not Install the humidifier where the

temperature is lower than 32°F (O°C) or higher

than 200°F (93°C).

• For all installation configurations, the mounting

area must be strong enough to support the

humidifier's weight when it is full of water

(approximately 18 lbs.), and to hold the

humidifier in a level position for safe, reliable

operation. Otherwise, additional duct

reinforcement will be necessary.

• If the installation includes exposed insulated

materials, a section of the ductwork must be

removed and replaced with rigid metal duct

extending at least 6 feet downstream from the

humidifier.

• Mount the unit at least 4-to-6 feet after the

plenum transition. Avoid sudden turns or

transitions in the ductwork in the immediate

area downstream from the humidifier.

There are three possible mounting procedures:

• horizontally under at least a 10 in. (254 mm) wide duct

using the mounting bracket (preferred mounting);

• horizontally under a reinforced duct;

• horizontally under a duct extension using the mounting

bracket.

Decide which mounting is appropriate and follow those

mounting instructions.

Mount Horizontally Using Mounting

Bracket (Preferred Mounting Method)

IMPORTANT

The duct must be at least 10 in. (254 mm) wide

to use this mounting method.

The duct is strongest when using the bracket mounting

method because the least amount of duct reinforcement

is required because of the bracket location. See Fig. 1.

However, in some installations, reinforcement may still be

necessary to help support the weight of the humidifier and

keep the humidifier level.

Position the bracket 1/2 in. (13 mm) from the edge of

the duct and trace around the bracket. See Fig. 4.

2. Once the outline has been traced, remove bracket.

Fig. 4. Position bracket to duct edge.

3. Drill a 3/8 in. (10 mm) hole within the center portion

of the bracket.

4. Use tin snips to cut around the outline of the

bracket.

IMPORTANT

Follow the dotted line carefully.

5. Remove the sheet metal.

6. Use two 8-32 screws and nuts to attach the mount-

ing bracket (L shaped with six holes) to the top/front

surface of the humidifier. The humidifier is now

ready for mounting.

NOTE: Position the humidifier so the upward protrusion

of the U is on the side toward the reservoir.

IMPORTANT

Do not mount the humidifier until the water level

is adjusted. See the Plumbing section.

7. Slide the flanges of the humidifier reservoir into the

mounting bracket until the reservoir’s front flange

comes into contact with the edge of the duct.

8. Secure the humidifier to the duct with three no. 8

sheet metal screws.

M10580B

HUMIDIFIER

HUMIDIFICATEUR

M23374

BRACKET

1/2 IN. (13 MM)

FROM EDGE

HE420A STEAM POWER HUMIDIFIER

369-1108—2

Mount Horizontally On Reinforced Duct

This horizontal mounting method usually requires duct

reinforcement to support the weight of the humidifier and

keep it level. The mounting bracket is not used. See Fig. 2.

1. Position the bracket to the bottom of the duct in the

desired location. Be sure the bracket is level.

2. Once the outline has been traced, remove bracket.

3. Drill a 3/8 in. (10 mm) hole within the center portion

of the bracket.

4. Use tin snips to cut around the outline of the

bracket.

5. Remove the sheet metal.

IMPORTANT

Do not mount the humidifier until the water level

is adjusted. See the Plumbing section.

6. Slide the flanges of the humidifier reservoir into the

mounting bracket.

7. Secure the humidifier to the duct with two no. 8

sheet metal screws.

Mount Horizontally On Vertical Duct

Horizontal mounting on a vertical duct requires the

installation of a duct extension. Additional duct

reinforcement may also be necessary to help support the

weight of the humidifier and keep it level. See Fig. 3.

Create and install the duct extension. Follow the steps in

the Mount Horizontally Using Mounting Bracket section to

complete installation.

WIRING

All wiring must comply with local codes and ordinances.

For complete wiring instructions, refer to the manual

“Wiring Instructions for High-Capacity Steam Humidifiers”

packaged with your HE420A humidifier.

PLUMBING THE HUMIDIFIER

CAUTION

Chemical Hazard.

Can cause damage to environment or air

conditioning system.

Do not use any refrigerant line connected to an air

conditioner.

Be sure to install the chlorine removal filter

(provided) to prevent humidifier corrosion.

NOTE: Either hard or soft water can be used in the

humidifier.

IMPORTANT

Use only copper tubing to plumb the humidifier.

1. Locate the cold water pipe closest to the humidifier.

2. Install the saddle valve connector.

3. Use the valve instructions to install the valve (pro-

vided). The valve is self-piercing when installed on

copper pipe.

IMPORTANT

Position the valve so water flows from the top or

side to reduce the chance of clogging the valve

with minerals.

Lightly clean the copper tubing ends with fine

sandpaper before making any connections.

Do not use any line connected to an air

conditioner.

4. Install the chlorine removal filter.

5. Place the brass compression nut over the copper

tubing.

6. Slide the brass ferrule over the tubing.

NOTE: Do not overtighten the compression nut.

Moderate tightness prevents leaking.

7. Insert the tubing into the valve fitting and tighten the

compression nut.

8. Flush the copper tubing to remove any debris that

can cause problems at the float valve.

9. Route the tubing to the humidifier float valve, keep-

ing the tube away from sharp edges.

10. Connect the remaining end of the tubing to the

humidifier float valve.

11. Open the saddle valve so that the water flows

slowly and gently into the water pan.

SET THE WATER LEVEL

CAUTION

Flooding Hazard.

Inadequate support of the float arm can lead to

valve seat damage resulting in water leakage.

Support the float arm during adjustment.

Adjust the humidifier water level prior to mounting.

1. Set the humidifier reservoir on a level surface.

2. Attach the water feed line and allow the unit to fill

until the float valve shuts off the incoming flow of

water. The water level should be between 2-1/4 in.

(57 mm) and 2-1/2 in. (64 mm) deep. If water level

is correct, skip to step 4.

3. Adjust the water level in small increments. Raise

the water level by pushing down on the center of

the float arm. Lower the water level by pressing the

float down with one hand and pulling up on the cen-

ter of the float arm with the other hand. See Fig. 5.

4. Verify the water level by removing enough water to

allow the float valve to automatically fill and shut off

the water.

Fig. 5. Adjusting the water level.

TO RAISE WATER LEVEL

PUSH

DOWN

TO LOWER WATER LEVEL

HOLD

DOWN

PUSH

M10581

HE420A STEAM POWER HUMIDIFIER

69-1108—2 4

FINISH MOUNTING AND PLUMBING

THE HUMIDIFIER

1. Mount the humidifier as instructed in the Select

Location and Mount section.

2. Route the tubing to the humidifier float valve.

IMPORTANT

Keep the tubing away from sharp edges.

3. Connect the remaining end of the tubing to the

humidifier float valve.

4. Open the saddle valve so the water flows slowly

into the water pan.

5. Check the compression fittings at the saddle valve

and the float valve. Tighten the fitting slightly to stop

any leakage.

6. Connect the overflow provision of the humidifier to a

suitable waste drain.

NOTE: 3/8 in. (9.525 mm) I.D. tubing can be easily

attached to the overflow fitting.

7. Support the drain line at several locations to pre-

vent kinks. Be sure to provide support near any

heat source.

8. Use a male 1-1/2 in. NPT fitting (not supplied) to

connect the humidifier overflow provision.

INSTALL THE AUTOMATIC

FLUSHING TIMER

Refer to the “Installation Instructions for the

Programmable Humidifier Automatic Flushing Timer” for

complete instruction.

INSTALL THE AUTOMATIC

HUMIDISTAT CONTROL

For additional humidistat installation instruction, refer to

the manual “Wiring Instructions for High-Capacity Steam

Humidifiers.”

WARNING

Electrocution Hazard. Disconnect electrical

power to the furnace before beginning

installation.

Sharp edges. Use caution when cutting plenum

openings and handling ductwork

CAUTION

Do not mount the compensating humidistat on

the supply duct or plenum. The unit will not

withstand supply temperatures.

Do not set the humidity so high that condensation

forms on windows or walls.

SELECT LOCATION AND MOUNT

1. Check contents of the humidistat carton. Compo-

nents include:

• Automatic humidistat

• Outdoor temperature sensor

• Sensor shield

• Manual mode faceplate

• Mounting bracket

2. Disassemble the humidistat. Pull knob off, then

remove the cover by inserting a screwdriver in the

slot on the right side of the humidistat.

3. Mount the humidistat on the COLD AIR RETURN.

Select a mounting location at least 6 inches

upstream from the fresh air intake ductwork, if appli-

cable.

4. Select an exterior location to mount the Outdoor

Temperature Sensor. Location must meet the fol-

lowing requirements. Incorrect indoor humidity lev-

els will result if these requirements are not met.

• Mount on North, Northeast or Northwest side of

house.

• Mount at least 3 feet from all exhaust vents.

• Mount above expected snow line.

NOTE: For manual operation, do not install the outdoor

sensor wire.

5. Locate an existing Indoor/Outdoor access hole.

• Make sure there are no active high-voltage

wires in the hole.

• As an alternative, the sensor can be mounted in

the center of a 6-inch fresh air intake duct (must

be no farther than 30 inches from the outside

wall).

NOTE: If neither configuration is possible, the compen-

sating humidistat can be installed to operate

manually. See Installing the Humidistat to Oper-

ate Manually, below.

6. Route the sensor wire to the selected location. Run

wire between the compensating humidistat and the

outdoor sensor lead. If the sensor is outdoors, snap

the probe end of the sensor into the sensor shield

and attach it to an exterior wall. The probe must be

completely covered by the shield.

NOTE: Outdoor temperature sensor wire must not

exceed 30 feet in length.

CAUTION

Do not run outdoor temperature sensor wire

alongside wires carrying high voltage (120

VAC or higher). Do not run the sensor wire

through conduit.

7. Attach the Sensor Wire to the humidistat. Strip the

connecting wire 1/4 inch and attach the two internal

wires to the terminals labeled “Outdoor Tempera-

ture Sensor” on the humidistat.

8. Select a power source. The voltage to the humidis-

tat must be between 22-30 VAC.

NOTE: The compensating humidistat will operate prop-

erly only with a continuous power source. A min-

imum 10 volt amperes is required.

9. Connect the humidistat to the humidifier. Strip the

wires used for all the humidistat terminal connec-

tions 1/4 inch.

10. Set the humidistat. Consult the compensating humi-

distat homeowner's manual for proper humidity set-

tings.

HE420A STEAM POWER HUMIDIFIER

569-1108—2

Installing the Humidistat to Operate

Manually

1. Locate the three-pin arrangement marked AUTO/

MAN protruding from the control board (right of wir-

ing connections).

2. Pull upward to remove the black, two-pin connector

from the auto position. Reinstall it in the manual

position (on the center and right-hand pins).

CAUTION

Do not attach sensor wire to the blue wiring

connection block.

3. Follow Steps 8 (select a power source) and 9 (Con-

nect the humidistat to the humidifier) to complete

the wiring. Apply the manual mode faceplate to the

compensating humidistat cover. Reattach the cover

to the base and reinstall the knob.

HUMIDISTAT OPERATING

INSTRUCTIONS

With automatic humidity control, you can control your

humidifier almost effortlessly, because:

• Once the knob has been set, the humidistat

automatically adjusts the indoor relative humidity

based on outdoor temperature and your desired

humidity level.

• The humidistat calculates the optimal humidity so you

don't have the problems associated with indoor

condensation.

• The humidistat’s temperature condensation capability

automatically turns itself on in cold weather, off in

warm weather.

• The humidistat’s humidity and temperature sensors

are solid-state, which means there are no mechanical

parts, and no problems associated with dust.

Automatic Operation

Once the humidistat is installed in the cold air return and

internally set to AUTOMATIC, turn the dial to 5 (the

standard humidity control setting).

Allow the humidity to stabilize for at least two days (home

size, furnace efficiency, and personal comfort preference

may affect the length of time necessary). At that point, you

may reset the dial to 6 for more humidity, or 4 for less

humidity. Continue adjusting the dial until you reach your

optimal indoor humidity level, and leave the dial in this

position.

Remember that in AUTO mode, the dial is not showing

relative humidity, but your preferred humidity setting

based on Table 1.

Manual Operation

For MANUAL operation, apply the manual mode decal to

the faceplate. Once the unit is installed in the cold air

return and internally set to MANUAL, turn the dial to the

expected outdoor temperature. The corresponding

optimal humidity level has been calibrated for you. For

example, by setting the dial to an anticipated 20°F, the

humidistat automatically maintains the indoor relative

humidity in the safe, comfortable 35% range (see Table 2

below).

In extreme cold weather, relative humidity must be

reduced to prevent condensation on windows and interior

surfaces. Otherwise, the excess moisture will eventually

cause damage to your home.

Additional Features

• When outdoor temperature exceeds 50°F (10°C), the

humidistat will function in Test mode only.

• When indoor relative humidity exceeds 45%, the

humidistat will not operate.

• Test Mode—Manual test the humidistat by turning the

knob to the far right. The unit will energize the internal

relay for one minute, allowing you to confirm proper

operation.

• Manual Off—In Manual mode, turn the humidistat OFF

during warm months by turning the knob to the far left.

(This is not necessary in Automatic mode.)

HUMIDISTAT CHECKOUT

IMPORTANT

If conditions exceed 50°F or 45 percent relative

humidity, it may be necessary to perform this

test.

1. To conduct a system test, ensure that 24 VAC is

applied to the 24 VAC terminals of the compensat-

ing humidistat.

2. Reattach the humidistat cover and knob to the

base.

3. Rotate the knob on the humidistat clockwise to the

“Test” position.

Table 1. Humidity Settings.

Dial

Position

Outdoor Temperature °F

-10 0 10 20 30 40

1 10% 10% 10% 15% 20% 25%

2 10% 10% 15% 20% 25% 30%

3 10% 15% 20% 25% 30% 35%

4 15% 20% 25% 30% 35% 40%

5 20% 25% 30% 35% 40% 45%

6 25% 30% 35% 40% 45% 45%

7 30% 35% 40% 45% 45% 45%

Table 2. Recommended Relative Humidity.

Outside Temperature Recommended RH

+40°F 45%

+30°F 40%

+20°F 35%

+10°F 30%

0°F 25%

-10°F 20%

-20°F 15%

Table 1. Humidity Settings.

Dial

Position

Outdoor Temperature °F

-10 0 10 20 30 40

HE420A STEAM POWER HUMIDIFIER

69-1108—2 6

a. If set up correctly, the humidifier will begin oper-

ating. In “Test” mode, the humidistat will operate

for approximately one minute.

b. If the humidifier does not activate properly in

“Test” mode, refer to Appendix A.

Set the humidistat. Refer to Humidistat Operating

Instructions for detailed instruction on initial settings.

a. If home is occupied, set the knob to “5”, or for

manual operation, set the knob to 35%.

b. If home is vacant, turn the knob to counterclock-

wise to “Off.”

INSTALL THE SAFETY CONTROL

SHUTOFF

Refer to the manual “Wiring Instructions for High-Capacity

Steam Humidifiers” (page 11) for complete instruction on

installing the Safety Control Shutoff.

CHECK THE HUMIDIFIER

OPERATION

After installation is complete, use the following steps to

check the humidifier operation:

1. Turn on the humidifier water supply.

2. Be sure the humidifier has power and then plug in

the humidifier.

3. Turn the Humidity Control to the Test position.

NOTE: If relative humidity is above 45% in the home, or

the outdoor temperature is above 50°F, a jumper

may need to be placed across the humidistat’s

OUT terminals to perform this checkout.

4. Check that the furnace blower comes on to circulate

the moist air. The blower may take as long as fifteen

minutes to start.

5. Refer to the Humidity Control owner’s manual for

operation.

HE420A STEAM POWER HUMIDIFIER

769-1108—2

APPENDIX A

Table 3. Compensating Humidistat Troubleshooting Guide.

PROBLEM SOLUTION NOTES

Humidifier does not

operate in “Test”

mode.

• Confirm the outdoor temperature sensor is

connected to the correct terminals on the

humidistat. (For manual operation, ensure the

jumper pins are positioned correctly.)

• Check wiring diagram (Figure 1) for correct

installation.

• Check the voltage at the humidistat “24 VAC”

terminals. (Should be 22-30 VAC.)

• Ensure the control knob has not been left in the

“Test” position.

Humidifier only

operates in “Test”

mode.

• Check the resistance of the sensor by removing

the leads from the humidistat terminals and

measuring the resistance across the wires with

an ohmmeter. Compare the reading to the

temperature/resistance chart (right).

• For automatic applications, make sure the

outdoor temperature sensor is mounted

completely outside the house (i.e. not recessed

into the hole) on the North, Northeast or

Northwest side, away from direct sunlight. And is

mounted at least 3 feet away from all exhaust

vents.

• If the outdoor temperature sensor is mounted in

the fresh air intake duct, make sure the probe is

no further than 30 inches from an outside wall.

Temp/Resistance Chart

100°F 6000 ohms 38°C

90°F 7500 ohms 32°C

80°F 9500 ohms 27°C

70°F 11,500 ohms 21°C

60°F 14,000 ohms 16°C

50°F 18,000 ohms 10°C

40°F 23,000 ohms 4°C

30°F 28,500 ohms -1°C

20°F 37,000 ohms -7°C

10°F 46,500 ohms -12°C

0°F 61,500 ohms -18°C

-10°F 78,500 ohms -23°C

-20°F 105,500 ohms -29°C

-30°F 135,000 ohms -34°C

Notes:

In automatic applications, if the outdoor

temperature is greater than +50°F (+10°C)

or less than -32°F (-35.6°C), the

compensating humidistat will not operate

(except in “Test” mode).

In both automatic and manual applications,

if the relative humidity in the home is

higher than the knob setting, the

humidistat will not operate. Similarly, the

humidistat will not operate if the indoor RH

exceeds 45%.

Humidifier operates

constantly.

• Check the humidistat setting. If the RH in the

home is less than the knob setting, the humidifier

will operate until the humidity level is higher than

the knob setting.

• In “Test” mode, verify that the humidifier will shut

off after approximately one minute.

• Check the resistance of the sensor.

• See previous Problem/Solution, regarding

outdoor temperature sensor mounting locations.

• Turn the humidistat “OFF” and observe whether

the humidifier turns off. If operation continues,

check Figure 1 wiring diagram. Remove the

wires from the humidistat's “OUT” terminals. If

humidifier continues to operate, check the

humidifier.

Humidifier or

compensating

humidistat “chatters”

or clicks on and off

rapidly.

• Use a voltmeter to check for steady 22-30 VAC.

• Make sure the outdoor temperature sensor

wiring does not run alongside the wires carrying

high voltage (120 VAC or higher).

Furnace or heat

pump blower system

runs continuously;

condensation is

building up in

ductwork.

• It may be necessary to make a setting change on

the furnace or heat pump board to prevent the

blower from shifting down to lowest idling speed.

• Consult the furnace/heat pump operating manual

or contact the manufacturer for procedures to

prevent low air flow.

HE420A STEAM POWER HUMIDIFIER

Automation and Control Solutions

Honeywell International Inc. Honeywell Limited-Honeywell Limitée

1985 Douglas Drive North 35 Dynamic Drive

Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9

customer.honeywell.com

® U.S. Registered Trademark

69-1108—2 M.S. Rev. 06-06

APPENDIX B

* Before the SCR can be reset, the system must be checked and repaired by a licensed contractor. To reset the SCR,

insert a rigid, small-diameter object (e.g. paperclip) into the smallest hole in the face of the SCR, next to the green

connector block. This, too, should be performed by an HVAC contractor.

Table 4. Safety Control Relay (SCR) Operation and Troubleshooting Guide.

Condition Cause Action Required

SCR LED shows rapid series of red,

green, and yellow lights, followed by

no LED display.

Condition Normal. SCR processor is

powering up and checking internal

operation.

No action required.

Humidifier won't operate. No SCR

LED display.

Problem! SCR circuit is not closing or

humidistat is not calling for humidity.

Check SCR power; check humidistat

operation. If humidity is about 45% or

outdoor temperature is above 50°F,

the humidifier won't operate unless the

humidistat is set to Test mode.

Humidifier operates. SCR LED shows

continuous yellow.

Condition Normal. This is a test phase.

SCR will wait 30 minutes to detect

furnace blower operation. If the

furnace blower is detected, the system

will function properly.

No action required.

Humidifier won't operate. SCR LED

shows continuous red.

Problem! During the 30 minute test

phase, the SCR failed to detect the

furnace blower and turned the

humidifier off.

Turn the humidistat off, then on again,

to reset the system. Although unlikely

to occur, this failure/reset process can

occur twice before further action is

necessary.

Humidifier operates. SCR LED shows

continuous green.

Condition Normal. All systems

(furnace, humidistat, humidifier and

SCR) are operating properly.

No action required.

Humidifier won't operate. SCR LED

shows flashing red.

Problem! The SCR failed to detect the

furnace blower for the third time and,

as a safety precaution, has locked out

the humidifier. This is an indication

that some aspect of the system

(furnace, humidistat, humidifier or

SCR) has malfunctioned.

Contact your HVAC contractor ASAP

to check out and repair the system.*

Honeywell HE420A User manual

Honeywell HE420A User manual

Honeywell HE420A User manual

Related papers

Other documents