Stairmaster 2019 Capacitive Touch Embedded 15 Inch Operating instructions

Type
Operating instructions

This manual is also suitable for

The Stairmaster 2019 Capacitive Touch Embedded 15 Inch is a cutting-edge fitness console that offers a variety of features to enhance your workout experience. With its large, 15-inch touchscreen display, you can easily navigate through various entertainment options, including TV, internet, and apps. The console also allows you to track your workout progress, set goals, and monitor your heart rate. Additionally, the console is compatible with a variety of fitness apps, allowing you to customize your workouts and stay motivated.

The Stairmaster 2019 Capacitive Touch Embedded 15 Inch is a cutting-edge fitness console that offers a variety of features to enhance your workout experience. With its large, 15-inch touchscreen display, you can easily navigate through various entertainment options, including TV, internet, and apps. The console also allows you to track your workout progress, set goals, and monitor your heart rate. Additionally, the console is compatible with a variety of fitness apps, allowing you to customize your workouts and stay motivated.

Install Instructions
Page 1
620-8504 Rev. B
Latest Rev.
For 8-UB (9-8120-XXXXXX) + 8-RB (9-8130-XXXXXX) +
8-CT (9-6140-XXXXXX) + 8-G (9-5250-XXXXXX) + 8-FC (9-5260- XXXXXX) +
8-VS (9-6160-XXXXXX):
Tools Required:
#2 Phillips Screwdriver
1. Using a phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable
inlets securing internal cables to the electrical plate .
NOTE: Please note that the instructions given on Pages 1-4 are valid for ALL UNITS, a Recumbent Bike is only
shown as an example. For STB/CAB install on all other units, please see below:
8-RDE Rear Drive Elliptical (Pg. 5)
Treadmills (Pg. 8)
8-FC FreeClimber (Pg. 10).
STB/CAB INSTALL INSTRUCTIONS
Applies to: All 8-Series Cardio w/15” STB-Ready Console
Install Instructions
Page 2
620-8504 Rev. B
2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing
path is represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI
cable to the other cables inside the unit as it is routed down through the machine.
9-6140-XXXXXX (8-CT)
9-5250-XXXXXX (8-G)
9-6140-XXXXXX (8-CT)
9-6140-XXXXXX (8-CT)
9-6150-XXXXXX (8-VS)
9-5260-XXXXXX (8-FC)
Install Instructions
Page 3
620-8504 Rev. B
3. Install the HDMI grommet onto the HDMI cable and the 90 degree RJ45 adapter onto the CSAFE cable.
4. Pass the HDMI cable through the bottom opening of the new electrical plate pulling the grommet through
the plate to secure it. Also install the 90 degree RJ45 adapter by passing it through the top hole in the electri-
cal plate and clicking it into place. Finally, secure the electrical plate to the frame using two (2) of the supplied
screws. Use the cable retention clamps as shown to secure any loose wires.
Install Instructions
Page 4
620-8504 Rev. B
5. Connect the CSAFE and HDMI cables running up to the 15” Embedded console to their respective connec-
tions. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right).
Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below.
6. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the
CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB*.
*Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit.
TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12.
Install Instructions
Page 5
620-8504 Rev. B
For 8-RDE (9-6150-XXXXXX):
Tools Required:
#2 Phillips Screwdriver
1. Using a phillips screwdriver, remove the electrical plate at the front of the unit then disconnect any cable
inlets securing internal cables to the electrical plate.
2. Route HDMI cable down through mast of machine and out of the front of the electrical plate. The routing
path is represented by the dark bold line below (Fig. 7). Be sure to used the included zip ties to secure the
HDMI cable to the other cables inside the unit as it is routed down through the machine.
Install Instructions
Page 6
620-8504 Rev. B
3. Install the 90 degree RJ45 adapter onto the CSAFE cable and push the adapter into the plate so it clicks into
place. Next, pass the HDMI cable through the cutout in the new electrical plate shown below.
4. Use two (2) of the supplied screws to install the HDMI cable retention plate. Finally, use two (2) of the supplied
screws to nish securing the new electrical plate to the frame, use the cable retention clamps as shown to
secure any loose wires.
Install Instructions
Page 7
620-8504 Rev. B
5. Connect the CSAFE and HDMI cables running up to the 15” Embedded console to their respective connec-
tions. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right).
Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below.
6. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the
CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB*
*Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit.
TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12.
Install Instructions
Page 8
620-8504 Rev. B
For Treadmills (9-9201-XXXXXX + 9-9202-XXXXXX + 9-9204-XXXXXX):
Tools Required:
#2 Phillips Screwdriver
1. Route HDMI cable down through mast of machine and out through the hole in the frame. The routing path is
represented by the dark bold line below. Be sure to used the included zip ties to secure the HDMI cable to the
other cables inside the unit as it is routed down through the machine.
2. Route the end of the HDMI cable out of the bottom of the treadmill frame where shown below. Use the cable
retention clamps to secure any loose wires.
Install Instructions
Page 9
620-8504 Rev. B
3. Connect the CSAFE and HDMI cables running up to the 15” Embedded console to their respective connec-
tions. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right).
Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below.
4. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the
CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB*
*Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit.
TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12.
Install Instructions
Page 10
620-8504 Rev. B
For FreeClimber (9-5260-XXXXXX):
Tools Required:
#2 Phillips Screwdriver
1. Route HDMI cable down through mast of machine and out through the hole in the frame (please note that
the user right side shroud has been removed for clarity. The routing path is represented by the dark bold line
below. Be sure to used the included zip ties to secure the HDMI cable to the other cables inside the unit as it is
routed down through the machine.
2. Route the end of the HDMI cable out of the bottom of the FreeClimber frame where shown below. Use the
cable retention clamps to secure any loose wires.
Install Instructions
Page 11
620-8504 Rev. B
3. Connect the CSAFE and HDMI cables running up to the 15” Embedded console to their respective connec-
tions. Connect the CSAFE cable where shown (image left) and the HDMI cable to the console (image right).
Secure the HDMI cable to the chassis of the console with the supplied copper tape as shown below.
4. Install the CAB-to-RJ45 adapter cable into the RJ45 port on the front of the unit, plug adapter cable into the
CAB, then plug the RJ45-to-3.5mm adapter cable into the CAB*
*Note that while the image above shows the CAB being installed onto an Upright Bike, the CAB installation process is the same for each unit.
TO CONTINUE INSTALLATION, PLEASE TURN TO PAGE 12.
Install Instructions
Page 12
620-8504 Rev. B
Installing the IR Emitter:
OPTION A:
If the set top box (STB) is located close to the unit, the IR emitter can be connected directly into the
RJ45-to-3.5mm as shown below:
OPTION B:
If the set top box (STB) is located farther away from the unit, such as inside an A/V closet, the
adapters can be combined with a length of customer-supplied CAT6 cable in order for the IR
emitter to reach the STB:
Install Instructions
Page 13
620-8504 Rev. B
Mounting the IR Emitter:
Once the 3.5mm end of the IR cable has installed into the CAB using either Option A or Option B
(see page 15), the IR diode end of the IR emitter will need to be attached to the front of the STB
where the IR receiver is located. If you cannot locate the IR receiver on the STB, shining a ashlight
at the front of the STB can help in locating it.
In the examples above, you can see the IR emitter mounted to the STB over the STB’s IR receiver.
The two examples on the left show common locations of the IR receiver on two STBs.
Once the IR diode is in place, install the IR shield onto the front of the IR diode (Fig. 17). This will en-
sure that the signal sent to the STB will only change the settings on the STB that the IR diode has
been applied to.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Stairmaster 2019 Capacitive Touch Embedded 15 Inch Operating instructions

Type
Operating instructions
This manual is also suitable for

The Stairmaster 2019 Capacitive Touch Embedded 15 Inch is a cutting-edge fitness console that offers a variety of features to enhance your workout experience. With its large, 15-inch touchscreen display, you can easily navigate through various entertainment options, including TV, internet, and apps. The console also allows you to track your workout progress, set goals, and monitor your heart rate. Additionally, the console is compatible with a variety of fitness apps, allowing you to customize your workouts and stay motivated.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI