Dome Camera
Hardware Manual
Z76
2020/05/18
www.acti.com
Hardware Manual
2
Table of Contents
Precautions 3
Regulatory Compliance .................................................................... 4
Safety and Compliance Information ................................................ 6
Introduction 9
List of Models .................................................................................... 9
Package Contents ........................................................................... 10
Physical Description ...................................................................... 11
Installation Procedures 12
Waterproof the RJ-45 Connector 18
Using the Cable Gland ................................................................. 18
Access the Camera 21
Configure the IP Addresses ........................................................... 21
Using DHCP Server to Assign IP Addresses ................................ 21
Using the Default Camera IP Address .......................................... 22
Access the Camera ......................................................................... 24
www.acti.com
Hardware Manual
3
Precautions
Read these instructions
Read all the safety and operating instructions before using this product.
Heed all warnings
Adhere to all the warnings on the product and in the instruction manual. Failure to follow the
safety instructions given may directly endanger people, cause damage to the system or to
other equipment.
Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Trademarks
ACTi and ACTi logo are registered trademarks of ACTi Corporation. All other names and
products used in this manual are registered trademarks of their respective companies.
Liability
Every reasonable care has been taken during the writing of this manual. Please inform your
local office if you find any inaccuracies or omissions. ACTi will not be held responsible for any
typographical or technical errors and reserves the right to make changes to the product and
manuals without prior notice.
www.acti.com
Hardware Manual
4
Regulatory Compliance
Federal Communications Commission Statement
This equipment has been tested and found to comply with the limits for a
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to the equipment that are not expressly approved by the
responsible party for compliance could void the user’s authority to operate the equipment.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
www.acti.com
Hardware Manual
5
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards
listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is marked
with this symbol, which may include lettering to indicate cadmium (Cd), lead
(Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
www.acti.com
Hardware Manual
6
Safety and Compliance Information
Installation and removal of the unit and its accessories must be carried out by qualified
personnel. You must read all of the Safety Instructions supplied with your equipment before
installation and operation.
Installation
This device is a class A product and may cause radio interference. Take measures if
necessary.
Make sure the camera operates in an environment where the temperature and humidity
meet requirements. Keep the camera from excessive pressure, vibration, moisture, dust,
and intensive electromagnetic radiation.
Use a power adapter or a PoE device that meets requirements. Otherwise, the device may
be damaged.
Make sure the length of the power cable between the power adapter and the camera is not
too long, otherwise the voltage of the camera is lowered, causing the camera to work
abnormally. If it is required to lengthen the power cable, lengthen the cable between the
power adapter and the mains.
Do not hold the tail cable by hand for weight bearing. Otherwise, the cable connector of the
camera could be loosened.
Do not cut the tail cable. Exposed tail cables may cause short circuit and damage the
camera.
When connecting to an external interface, use an existing connection terminal, and ensure
that the cable terminal (latch or clamp) is in good condition and properly fastened. Ensure
that the cable is not tense during mounting, with a proper margin reserved to avoid poor
port contact or loosening caused by shock or shake.
The end of the tail cable must be kept under good protection. Take waterproof measures to
protect the tail cable.
During the process of transportation, special attention is required for the protection of the
transparent dome cover to prevent friction, scratch and contamination, etc. In order to
keep the cover clean, do not remove the protective film on the cover during mounting. After
mounting is finished, remove the film before the device is powered on.
Contact professionals for maintenance information. Do not attempt to dismantle the device
by yourself. We shall not assume any responsibility for problems caused by unauthorized
repair or maintenance.
www.acti.com
Hardware Manual
7
Maintenance
If there is dust on the front glass surface, remove the dust gently using an oil-free brush or
a rubber dust blowing ball.
If there is grease or a dust stain on the front glass surface, clean the glass surface gently
from the center outward using anti-static gloves or an oil-free cloth. If the grease or the
stain still cannot be removed, use anti-static gloves or an oil-free cloth dipped with
detergent and clean the glass surface gently until it is removed.
Do not use organic solvents, such as benzene or ethanol when cleaning the transparent
dome cover.
Never look at the transmit laser while the power is on. Never look
directly at the fiber ports and the fiber cable ends when they are
powered on.
Use of controls or adjustments to the performance or procedures
other than those specified herein may result in hazardous laser
emissions.
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
For device with this sticker, this device is intended for installation in a restricted access
location, access can only be gained by service persons or by users who
have been instructed about the reasons for the restrictions applied to the
location and about any precautions that shall be taken.
Proper configuration of all passwords and other security settings is the responsibility of
the installer and/or end-user.
In the use of the product, you must be in strict compliance with the electrical safety
regulations of the nation and region. Please refer to technical specifications for
detailed information.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited
Power Source with 12 VDC according to the IEC60950-1 standard. Please refer to
technical specifications for detailed information.
Do not connect several devices to one power adapter as adapter overload may cause
over-heating or a fire hazard.
Please make sure that the plug is firmly connected to the power socket. When the
product is mounted on wall or ceiling, the device shall be firmly fixed.
If smoke, odor or noise rise from the device, turn off the power at once and unplug the
power cable, and then please contact the service center.
www.acti.com
Hardware Manual
8
Cautions
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is necessary, use clean cloth
with a bit of ethanol and wipe it gently. If the camera will not be used for an extended
period, please replace the lens cap to protect the sensor from dirt.
Do not aim the camera at the sun or extra bright places. Blooming or smearing may
occur otherwise (which is not a malfunction), and affect the endurance of sensor at the
same time.
The sensor may be burned out by a laser beam, so when any laser equipment is in
using, make sure that the surface of sensor will not be exposed to the laser beam.
Do not place the camera in extremely hot, cold (the operating temperature shall be-30°
C to +60° C, or -40° C to +60° C if the camera model has an "H" in its suffix), dusty or
damp locations, and do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for operating environment.
Keep the camera away from liquid while in use.
While in delivery, the camera shall be packed in its original packing, or packing of the
same texture.
Regular part replacement: a few parts (e.g. electrolytic capacitor) of the equipment
shall be replaced regularly according to their average enduring time. The average time
varies because of differences between operating environment and using history, so
regular checking is recommended for all the users. Please contact with your dealer for
more details.
Improper use or replacement of the battery may result in hazard of explosion. Replace
with the same or equivalent type only. Dispose of used batteries according to the
instructions provided by the battery manufacturer.
If the product does not work properly, please contact your dealer or the nearest service
center. Never attempt to disassemble the camera yourself. (We shall not assume any
responsibility for problems caused by unauthorized repair or maintenance.)
www.acti.com
Hardware Manual
9
Introduction
List of Models
This hardware manual contains the following models:
Z76
2MP Outdoor Zoom Dome with D/N, Adaptive IR, Basic WDR,
Superior Low Light Sensitivity, Fixed Lens
www.acti.com
Hardware Manual
10
Package Contents
Check if the camera package comes with the following items:
Camera
Cable Gland
with Rubber and Washer
Wrench
Mounting Screw Kit
Drill Template
Quick Guide &
Warranty Card
IMPORTANT: When the camera is taken out from the box, the lens cover is covered by a thin
film. DO NOT remove this film. It is used to protect the lens cover from scratches or fingerprint
marks which may happen during installation. Remove this film only after the camera is
securely installed and all connections are complete.
Drill Template
Warranty Card
www.acti.com
Hardware Manual
11
Physical Description
Item
Description
1
DC 12V Power Input
Jack
This connector is used to connect to a DC 12V power
adapter if a non-PoE network connection will be used.
2
Ethernet Port
Connects to a network using an Ethernet cable.
3
Built-in Microphone
Receives audio input.
www.acti.com
Hardware Manual
12
Installation Procedures
The images on this section are for reference only; actual lens and cables may vary.
1. Locate the positions of the holes; paste the drill template stickers on the ceiling and drill
according to the images below.
A. Cables Going Through the Ceiling
B. Cables Going Along the Ceiling
2. Insert the plastic anchors.
www.acti.com
Hardware Manual
13
3. Twist the cosmetic ring of the camera.
4. Route the cables through the ceiling (A) or along the ceiling (B).
If the cable will be routed along the wall, then cut off the camera tab to where the cable will
pass through.
www.acti.com
Hardware Manual
14
5. Secure the ground screw.
6. Connect the cables. See ** for the detailed description on how to waterproof the Ethernet
cable.
www.acti.com
Hardware Manual
15
7. (Optional) If the camera will be connected to the DC 12V power, connect the power cable
and wrap the cable with waterproof tape.
NOTE: If the DC12V connector will not be used, wrap it also in waterproof tape to avoid
short circuiting the connector.
8. Mount the camera to the ceiling using the three (3) bundled screws.
www.acti.com
Hardware Manual
16
9. Access the camera to see the viewing angle (see Access the Camera on page 21). Then,
adjust the camera tilt and rotation, as needed.
10. To pan the camera, loosen the set screw using the bundled wrench. Then, rotate the
camera body.
11. Tighten the screw to fix the camera position.
www.acti.com
Hardware Manual
17
12. Attach the cosmetic ring to complete the installation.
www.acti.com
Hardware Manual
18
Waterproof the RJ-45 Connector
The camera and the pre-installed network cable, “pigtail”, are resistant to salt, water, weak acid,
alcohol, oil, grease and other common solvents. If the camera will be installed indoors, simply
connect the network side cable to the camera Ethernet port.
However, if the camera will be installed outdoors, ensure that the cable connections are
protected from different environmental factors. Use the bundled cable gland to protect the
Ethernet connection and use a waterproof tape to protect other cable connections.
DISCLAIMER: ACTi will not be responsible for camera damage caused by water entering
the cable connections.
Using the Cable Gland
This section describes how to waterproof the cable-out or “pigtail” of the camera using the
bundled cable gland. Before connection, prepare an exterior-grade Ethernet cable with RJ-45
connector.
Perform the following to waterproof the “pigtail” using the cable gland:
1. Attach the washer to the Ethernet connector of the camera.
2. Detach the clamping nut and sealing insert from the gland body:
Gland Body
Clamping Nut
Sealing Insert
www.acti.com
Hardware Manual
19
3. Insert the clamping nut into the Ethernet cable.
4. Insert the sealing insert through the Ethernet cable.
5. Insert the cable through the gland body.
6. Push the sealing insert into the gland body.
www.acti.com
Hardware Manual
20
7. Connect the RJ-45 connector to the camera connector.
8. Attach the gland body to the camera connector.
9. Attach the clamping nut to the gland body to complete the cable solution.
NOTE: Make sure the clamping nut is tightly attached to the cable gland body and the
sealing insert is squeezed tightly.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/