UNIVIEW IPC3612ER3-PF28 Quick Manual
- Category
- Security cameras
- Type
- Quick Manual
This manual is also suitable for
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
Notice
The default password is used for your first login. To ensure
account security, please change the password after your
first login. You are recommended to set a strong password
(no less than eight characters).
The contents of this document are subject to change without
prior notice. Updates will be added to the new version of this
manual. We will readily improve or update the products or
procedures described in the manual.
Best effort has been made to verify the integrity and
correctness of the contents in this document, but no
statement, information, or recommendation in this manual
shall constitute formal guarantee of any kind, expressed or
implied. We shall not be held responsible for any technical or
typographical errors in this manual.
The product appearance shown in this manual is for
reference only and may be different from the actual
appearance of your device.
This manual is a guide for multiple product models and so it
is not intended for any specific product.
Due to uncertainties such as physical environment,
discrepancy may exist between the actual values and
reference values provided in this manual. The ultimate right
to interpretation resides in our company.
Use of this document and the subsequent results shall be
entirely on the user’s own responsibility.
Environmental Protection
This product has been designed to comply with the requirements
on environmental protection. For the proper storage, use and
disposal of this product, national laws and regulations must be
observed.
Conventions
Document Conventions
Convention
Description
Boldface font
Commands, keywords, parameters and GUI
elements such as window, tab, dialog box,
menu, button, etc.
Italic font
Variables for which you supply values.
>
Separate a series of menu items, for example,
Device Management > Add Device.
Symbols
Symbol
Description
WARNING!
Contains important safety instructions and
indicates situations that could cause bodily
injury.
CAUTION!
Means reader be careful and improper
operations may cause damage or
malfunction to product.
NOTE!
Means useful or supplemental information
about the use of product.
Safety and Compliance Information
Conventions Used Symbol
The symbols in this chapter are shown in the following table. They
are used to remind the reader of the safety precautions during
equipment installation and maintenance.
Safety Symbol
Description
Generic alarm symbol: To suggest a general
safety concern.
ESD protection symbol: To suggest
electrostatic-sensitive equipment.
Safety Symbol
Description
Electric shock symbol: To suggest a danger of
high voltage.
Safety Information
WARNING!
Installation and removal of the unit and its accessories
must be carried out by qualified personnel. You must read
all of the Safety Instructions supplied with your equipment
before installation and operation.
Warnings:
If the product does not work properly, please contact your
dealer. Never attempt to disassemble the camera yourself.
(We shall not assume any responsibility for problems caused
by unauthorized repair or maintenance.)
Make sure the power supply voltage is correct before using
the camera. Use a power adapter or a PoE device that meets
requirements. Otherwise, the camera may be damaged.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period
of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or
incandescent lamp. The strong light can cause fatal damage
to the camera.
The sensor may be burned out by a laser beam, so when any
laser equipment is being used, make sure that the surface of
the sensor not be exposed to the laser beam.
Make sure the camera operates in an environment where
the temperature and humidity meet requirements. Keep the
camera from excessive pressure, vibration, moisture, dust,
and intensive electromagnetic radiation.
Keep the length of the power cord between the power
adapter and the camera within 1.5 meters, otherwise, the
power voltage on the camera may be lowered and may
cause exception.
Disconnect power before you move the camera. The camera
is powered on when the power cord is connected to the
power source. Do not move the camera by lifting the tail
cable.
Do not cut the tail cable. Exposed tail cables may cause short
circuit and damage the camera.
Use the power cable connector delivered with the camera.
Make sure the connector is in good condition (clip) and
secured into place. Do not fully stretch the power cord,
otherwise, the connector may be loose or disconnected due
to vibration or shake.
Use waterproof tape to protect the end of the tail cable.
Keep the tail cable from water.
When cleaning the camera, wipe the surface using clean and
soft cloth dipped with alcohol. When cleaning the lens, use
small amount of neutral detergent. Do not use thinner or
benzene.
Maintenance Precautions:
If there is dust on the front glass surface, remove the dust
gently using an oil-free brush or a rubber dust blowing ball.
If there is grease or a dust stain on the front glass surface,
clean the glass surface gently from the center outward using
anti-static gloves or an oil-free cloth. If the grease or the
stain still cannot be removed, use anti-static gloves or an
oil-free cloth dipped with detergent and clean the glass
surface gently until it is removed.
Do not use organic solvents, such as benzene or ethanol
when cleaning the front glass surface.
Caution: Fiber optic ports – optical safety.
Never look at the transmit laser while the power is on.
Never look directly at the fiber ports and the fiber cable
ends when they are powered on.
Caution: Use of controls or adjustments to the performance
or procedures other than those specified herein may result
in hazardous laser emissions.
Regulatory Compliance
FCC Part 15
This equipment has been tested and found to comply with the
limits for digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
This product complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
LVD/EMC Directive
This product complies with the European Low Voltage Directive
2006/95/EC and EMC Directive 2004/108/EC.
i
Contents
1 Appearance Description ......................................................... 1
Dimensions and Appearance ................................................... 1
Camera Structure ..................................................................... 1
2 Mounting Your Camera .......................................................... 3
Ceiling Mount ........................................................................... 3
Waterproof Components for RJ45 Plug ................................... 6
Starting the Camera ................................................................. 9
3 Setting Your Camera over the LAN ......................................... 9
4 Accessing Your Camera ......................................................... 10
System Requirements for Your PC ......................................... 11
Accessing Your Camera .......................................................... 11
Installing the ActiveX ............................................................. 13
2
Type B with Common Ethernet Copper Interface
No.
Description
No.
Description
Bottom ring
Housing
Lens
Infrared indicator
Power interface (12 VDC)
Ethernet interface
For the latest specifications, see the product
datasheets.
To protect RJ45 plug (see Type A with Waterproof
Ethernet Copper Interface) from water, see Waterproof
Components for RJ45 Plug.
6
1
2
3
4
5
3
2 Mounting Your Camera
You can use ceiling mount or wall mount, but you need to buy the
mount accessories separately. Make sure that the ceiling or wall
can hold the weight of the camera. The steps for ceiling mount
and wall mount are similar. The following takes ceiling mount as
an example.
Ceiling Mount
1. Attach the sticker to ceiling, and then drill holes according to
the sticker.
2. Insert the plastic plugs.
Sticker
Drill two guide holes (30-mm deep) using a
drill bit (6 mm or 6.5 mm in diameter)
4
3. Remove the bottom ring.
4. Connect the cable and then secure the dome.
5. Adjust the monitoring direction.
Drill a hole to lead cables out of the ceiling
Knock in plugs
Turn bottom ring anticlockwise
to loosen it
Connect cable and protect it with
waterproof tape
Attach dome to ceiling
with taping screws
5
6. Mount the bottom ring.
The above steps are for concealed installation. To use open
installation, lead the cables out from the open slots on the
bottom ring and see Mount the bottom ring. to finish the
installation.
The dome can rotate 360
degrees horizontally
The lens can rotate 80
degrees vertically
Push bottom ring back up and turn
it clockwise to lock into position
6
When you use open installation, make sure that the cable
can be led out through the open slot on the bottom ring
and then screw the dome to the wall as shown in the step
4.
Waterproof Components for RJ45 Plug
This section only applies to the RJ45 plug (see Type A with
Waterproof Ethernet Copper Interface).
1. Attach the seal ring to the copper interface.
Lock
Open slot on bottom ring
7
2. Mount the waterproof components.
You can crimp the inner wires of the cable with the RJ45 plug
first and then cover the waterproof components. You may
also cover the waterproof components first.
3. Insert the cylindrical waterproof ring into bolt.
Seal ring
12
3
Insert in order
Cylindrical waterproof ring
Waterproof bolt
9
Starting the Camera
To power on the camera you need to buy a power adapter
separately. After you have mounted the camera properly, connect
the camera to power.
3 Setting Your Camera over the LAN
To view and configure your camera via the LAN (Local Area
Network), you need to install the EZStation to find your camera
and change its IP address.
Please contact your dealer to obtain the EZStation.
Please refer to the user manual of EZStation for
detailed information.
1. Connect your camera and your PC as shown in the figure
below to ensure the routing is available.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
UNIVIEW IPC3612ER3-PF28 Quick Manual
- Category
- Security cameras
- Type
- Quick Manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI