Johnson Controls MAP 1850 Quick start guide

Brand: Johnson Controls

Model: MAP 1850

Type: Quick start guide

Part No. 24-10737-83, Rev. A

SMART Chiller Access Portal (SC-AP)

Gateway

SC-AP Gateway is a specialized version of the MAP

Gateway for use with SMART Connected Chillers (SCC).

• Access SC Equip cards on Smart Chillers using

Wi-Fi, Ethernet networks, or cellular modems.

• Send chiller data to the cloud for remote storage and

operations as part of our SCC Solution.

IMPORTANT: Save this guide. It contains default

user name and password information that may be

needed if you need to reset your SC-AP Gateway to

factory defaults.

European Single

Point of Contact:

NA/SA Single Point of

Contact:

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

APAC Single Point of Contact:

JOHNSON CONTROLS

C/O CONTROLS PRODUCT MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

QUICK START GUIDE

SMART Chiller

Access Portal

Gateway

Connect to Remote Services

This step assumes that you have already con-

figured a cellular router or have access to a good Ether-

net network for communications with the data cloud. Go

to the Wi-Fi client screen in SC-AP.

a. If you are using a cellular connection to access the

chiller communications card go to the SC Equip App

for your device and navigate to Settings > Wi-Fi

Client and set the Enabled field to On using the

drop down list.

b. If you are using an Ethernet connection to access

the chiller communications card go to the SC Equip

App for your device and navigate to Settings >

Ethernet and set the Enabled field to On using the

drop down list.

c. Go to Settings > Remote Services and Enter the

Remote Services Credentials (Segway) received via

email.

d. The MAP1850 device comes online. If the SC-AP is

out of date it updates as soon as connected to the

cloud. This can take 5 to 20 minutes. After updating

a Disconnect message appears. After 7 minutes the

SC-AP reboots and is ready for operation.

Refer to the Mobile Access Portal Gateway Network and

IT Guidance Technical Bulletin (LIT-12012015) for

information on Security Certificates.

Use the SC-AP Gateway

Once a data connection appears to be estab-

lished, use the CSD Mobile Application to

ensure that data is flowing and the connection is healthy.

IMPORTANT: Keep your SC-AP Gateway in the

optional protective shell or stationary cradle with

which it shipped. These may help protect the unit if it

is dropped.

GETTING STARTED

Refer to the Smart Chiller Access Portal Gateway Installation Instructions (Part No. 24-10737-75) for important product application information.

Connect the SC-AP Gateway to

Equipment

Use the supplied RJ-12 cable or field bus

adapter to connect the RS-485 port of the

SC-AP Gateway to the CS RJ Jack (Connected Service)

port on the SC Equip card. If mounting remotely, use an

approved power supply. The SC-AP Gateway is not

rated for outdoor use. If attaching to a chiller that is

installed outdoors, you must mount the SC-AP Gateway

remotely indoors. Refer to the SMART Chiller Access

Portal Installation Instructions (Part No. 24-10737-75) for

use cases and mounting instructions.

The SC-AP Gateway LEDs

flash, indicating that the device

is initializing. When the Fault

LED turns off and the Wi-Fi

LEDs flash in succession, the

SC-AP Gateway is ready to

use.

Connect to the

SC-AP Gateway

Wi-Fi Network

In the Wi-Fi settings of your mobile device or laptop, con-

nect to the SC-AP

Gateway Wi-Fi network using the following default cre-

dentials:

Place Label

Here.

SSID:

Passphrase:

Open a Web Browser

Direct your browser to www.mapgwy.com to open the

SC-AP Gateway browser interface.

SC-AP Gateway ships with a private

mapgwy.com SSL certificate installed to ensure secure

communication with the SC-AP Gateway. However, this

certificate does not indicate that it is trusted in a browser.

If you wish to install your own certificate, refer to Installing

a Security Certificate on a Client That is Connecting to

MAP Gateway in the Mobile Access Portal Gateway

Network and IT Guidance Technical Bulletin (LIT-

12012015) for more information.

Use the following default Admin login

credentials:

Read and accept the SC-AP Gateway license agreement.

Change Passwords

The first time you log in to the SC-AP Gateway,

the Change Password and Passphrase web

page appears. You must change the Admin password and

Wi-Fi passphrase.

Place Label

Here.

User:

Password:

a. Replace the default password in the New Admin

Password field. Confirm the change by entering the

new password in the Verify New Admin Password

field.

b. Replace the Wi-Fi Passphrase in the New Wi-Fi

Passphrase field and click Save.

c. Log in to the SC-AP with new credentials.

Continue to Step 6.

IMPORTANT: After you change the Wi-Fi passphrase

or SSID, the web server restarts and you must

rejoin the SC-AP Gateway Wi-Fi network using the

new passphrase. On some mobile devices, you must

select and forget the original SC-AP Gateway Wi-Fi

network before rejoining the network with the new

passphrase.

Johnson Controls MAP 1850 Quick start guide

Johnson Controls MAP 1850 Quick start guide

Johnson Controls MAP 1850 Quick start guide

Related papers

Other documents