44721
87535
Plymouth, Michigan
F75116
FASTENER KIT
38
c
SHEET OF
5-13-14
11
2002, 2011, 2014 Cequent Performance Products
HITCH NO.
VEHICLE
APPROX WEIGHT (LB.)
NOTE:
weight and tongue weight. Do not cut access or attachment holes with a torch.
Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is
removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A
hitch or ball which has been damaged should be removed and replaced. Observe safety precautions
when working beneath a vehicle and wear eye protection. Follow car maker's specs for maximum trailer
APPROX WEIGHT (LB.)
weight and tongue weight. Do not cut access or attachment holes with a torch.
when working beneath a vehicle and wear eye protection. Follow car maker's specs for maximum trailer
hitch or ball which has been damaged should be removed and replaced. Observe safety precautions
removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A
Check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is
NOTE:
FLAT WASHERS AND NUT.
COOLING. SECURE WITH
WITH REAR HEATING AND
DRILL BITS:
WRENCHES:
EQUIPMENT REQUIRED:
WIRING ACCESS LOCATION:
INSTALLATION INSTRUCTIONS
(TIGHTEN ALL FASTENERS WITH TORQUE WRENCH)
SYSTEMS OF THE STATE OF NEW YORK AND V.E.S.C. REGULATION V-5.
THIS PRODUCT COMPLIES WITH SAFETY SPECIFICATIONS AND REQUIREMENTS FOR CONNECTING DEVICES AND TOWING
OEM BOLTS
OEM BOLT
FLATWASHER
FLATWASHER
NUT
MITSUBISHI MONTERO
75116
HITCH SHOWN IN PROPER POSITION
BRACKET ASSEMBLY.
1. REMOVE THE PLASTIC FASCIA BY REMOVING THE TWO BOTTOM FASTENERS FROM THE TIE DOWN
CABLE TIES
PLASTIC FASCIA
IF STABILIZING PIN (7651) IS NOT INSTALLED.
J-PIN
(Order Separately)
OPTIONAL LOCKING STABILIZING PIN
HITCH REQUIRES 5/8" PIN AND CLIP
MAX GROSS
5500
5000
TRLR WT(LB)
BALL MOUNT
WEIGHT CARRYING
WEIGHT DISTRIBUTING
HITCH TYPE
DO NOT EXCEED LOWER OF
TOWING VEHICLE MFR'S RATINGS OR
WT(LB)
MAX TONGUE
550
500
OEM BOLTS
IN FRAME ON VEHICLES
FORWARD BOLT IS TRAPPED
ASSEMBLY
TIE DOWN BRACKET
FRAME
FASCIA
WELDNUTS
EXISTING
WELDNUTS
EXISTING
FRAME RAIL
(TIGHTEN ALL FASTENERS WITH TORQUE WRENCH)
SYSTEMS OF THE STATE OF NEW YORK AND V.E.S.C. REGULATION V-5.
THIS PRODUCT COMPLIES WITH SAFETY SPECIFICATIONS AND REQUIREMENTS FOR CONNECTING DEVICES AND TOWING
SUV1, SUV2
5. REATTACH THE PLASTIC FASCIA WITH THE CABLE TIES PROVIDED.
4. RAISE THE HITCH INTO POSITION AND ATTACH WITH THE OEM BOLTS REMOVED IN STEP 2.
PASSENGER SIDE BOLT WITH THE WASHERS AND NUT PROVIDED TO PREVENT RATTLES.
3. IF THE VEHICLE IS EQUIPPED WITH THE REAR HEATING AND COOLING UNIT, SECURE THE FORWARD
2. REMOVE THE TIE DOWN BRACKET ASSEMBLY AND RETURN TO VEHICLE OWNER.
10mm, 17mm, 19mm
TIGHTEN ALL M12 CL8.8 FASTENERS TO 68 LB-FT.
Printed in Mexico
-
1
Draw-Tite 75116 Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Draw-Tite 75116 Installation guide
-
-
-
-
-
-
-
-
-