MAKE: STYLE:
45
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY
For more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY:
MODERATE
MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 1.877.287.8634
Safety glasses should be
worn at all times while
installing this product
.
YEARS:
2015-PRESENT LAND ROVER MODEL: DISCOVERY SPORT SUV
4,500
675
TRAILER WEIGHT:
TONGUE WEIGHT:
13396 INSTALLATION INSTRUCTIONS
LBS.
LBS.
90
MIN.
MIN.
PRO INSTALL TIME:
NOVICE INSTALL TIME:
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
SCAN FOR
MORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product
voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.com
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
1/14/2019
EASY
PART REMOVAL
UNDERBODY PANEL AND LOWER
BUMPER COVER FASCIA
UNDERBODY PANEL (AS NEEDED)
AND LOWER BUMPER COVER
FASCIA
NO DRILLING REQUIRED
RATCHET
SOCKET
10mm
18mm
22mm
TORQUE
WRENCH
SOCKET
EXTENSION
6"
MASKING
TAPE
TAPE
MEASURE
SAFETY
GLASSES
DIE GRINDER
CUT-OFF
WHEEL
LOWER EXHAUST (3) HANGERS
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
WASHER,FLAT,5/8,YZ30-0013161
WASHER,LOCK,5/8,YZ
30-0013262
HEX BOLT10-1047163
1) Remove (1) bolt attaching the rubber exhaust isolator
brackets to the frame with a 10mm socket. Lift the rubber
isolator brackets off of the frame. Remove (1) rubber
exhaust hanger further forward under the vehicle.
NOTE: Support the forward exhaust when removing hangers.
2) Remove (8) nuts and (10) bolts using a 10mm socket
to remove the plastic underbody panel and lower
bumper cover fascia.
TRUNK PAN
EXISTING FRAME
WELDNUTS
PASSENGER SIDE
FRAME RAIL
DRIVER SIDE
FRAME RAIL
2
1
3
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
3) If present, remove the (2) hex flange bolts using an
18mm socket on the passenger side of the frame and
return to owner.
4) Raise the hitch into positon, loosely install (6) supplied
hex bolts, lock washers and washers with a 22mm
socket as shown.
5) Torque all 14mm fasteners to 88 lb-ft.
7) Trim the lower bumper cover fascia as shown in the
diagram above and reinstall.
6) Trim the plastic underbody panel as needed and
reinstall. Reinstall exhaust.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser.
If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to
repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
4,500 675
43
45
LAND ROVER DISCOVERY SPORT
5/19/2020
13396
90
Scan
for more
information
Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
WASHER,FLAT,5/8,YZ30-0013161
WASHER,LOCK,5/8,YZ
30-0013262
HEX BOLT
10-1047163
1
2
3
DRIVER SIDE
FRAME RAIL
DRIVER SIDE
FRAME RAIL
PASSENGER SIDE
FRAME RAIL
TRUNK PAN
EXISTING FRAME
WELDNUTS
- LOWER EXHAUST
- NO DRILLING REQUIRED
- TRIMMING REQUIRED
- REMOVE UNDERBODY PANEL
1) Remove (1) bolt attaching the rubber exhaust isolator brackets to the frame with a 10mm socket. Lift the rubber isolator
brackets off of the frame. Remove (1) rubber exhaust hanger further forward under the vehicle.
NOTE:
Be sure to support the exhaust when removing hangers.
2) Remove (8) nuts and (10) bolts using a 10mm socket to remove the plastic underbody panel and lower bumper cover fascia.
3) If present, remove the (2) hex flange bolts using an 18mm socket on the passenger side of the frame and return to owner.
4) Raise the hitch into positon, loosely install (6) supplied hex bolts, lock washers and washers with a 22mm socket as shown.
5) Torque all 14mm fasteners to 88 lb-ft.
6) Trim the plastic underbody panel as needed and reinstall. Reinstall exhaust.
7) Trim the lower bumper cover fascia as shown in the diagram above and reinstall.
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" SOCKET EXTENSION
10mm, 18mm, 22mm SOCKETS
DIE GRINDER w/ CUTOFF WHEEL
MASKING TAPE / MARKER
TAPE MEASURE
SAFETY GLASSES
TRIM DIMENSIONS ARE REFERANCE ONLY
/