Silvercrest Z32138 Assembly, Operating And Safety Instructions

IAN 43150

WIRELESS DOORBELL

FUNKTÜRKLINGEL

Montage-, Bedienungs- und Sicherheitshinweise

WIRELESS DOORBELL

Assembly, operating and safety instructions

TRÅDLØS DØRKL OKKE

Monterings-, betjenings- og sikkerhedshenvisninger

RADIOSTYRD DÖRRKLOCKA

Monterings-, bruks- och säkerhetsanvisningar

43150_Funktürklingel_cover_GB_IE_SE_DK.indd 2 26.03.14 15:57

GB / IE Assembly, operating and safety instructions Page 9

SE Monterings-, bruks- och säkerhetsanvisningar Sidan 24

DK Monterings-, betjenings- og sikkerhedshenvisninger Side 38

DE / AT / CH Montage-, Bedienungs- und Sicherheitshinweise Seite 52

43150_Funktürklingel_cover_GB_IE_SE_DK.indd 3 26.03.14 15:57

3

You need

Du behöver

Du skal bruge

Sie benötigen:

ø 6 mm

A

1

6

2

3

4

9

10

5

7

Z32138 Z32139

43150_Funktürklingel_content_GB_IE_SE_DK.indd 3 26.03.14 15:57

4

B

C1

8

6

181211

15

43150_Funktürklingel_content_GB_IE_SE_DK.indd 4 26.03.14 15:57

5

D

C2

7

16

14 13

17

43150_Funktürklingel_content_GB_IE_SE_DK.indd 5 26.03.14 15:57

6

E

F

17

16

14

43150_Funktürklingel_content_GB_IE_SE_DK.indd 6 26.03.14 15:57

7

G H

12 18

19

18

12

C B A

43150_Funktürklingel_content_GB_IE_SE_DK.indd 7 26.03.14 15:57

8

I

J

43150_Funktürklingel_content_GB_IE_SE_DK.indd 8 26.03.14 15:57

9 GB/IE

Introduction

Intended use .......................................................................................Page 10

Parts and features ...............................................................................Page 10

Included items .....................................................................................Page 11

Technical data ....................................................................................Page 12

Safety

General safety information ................................................................Page 12

Safety instructions for batteries ..........................................................Page 13

Assembly ........................................................................................Page 14

Preparing for use

Inserting / replacing the batteries ......................................................Page 15

Synchronising transmitter / receiver ...................................................Page 16

Setting the signal type ........................................................................Page 17

Setting the volume ..............................................................................Page 17

Selecting the chime .............................................................................Page 18

The procedure for connecting the transmitter to

existing bell system or existing doorbell button ................................Page 18

Connecting the transmitter

to a existing bell system ...................................................Page 19

Connecting a existing doorbell button ................Page 19

Troubleshooting........................................................................Page 20

Cleaning and maintenance .............................................Page 20

Disposal ............................................................................................Page 20

Declaration of conformity................................................Page 21

Warranty ........................................................................................Page 22

43150_Funktürklingel_content_GB_IE_SE_DK.indd 9 26.03.14 15:57

10 GB/IE

Wireless Doorbell

Introduction

Keep these instructions in a safe place. If you pass the

product on to anyone else, please ensure that you also pass

on all the documentation.

Intended use

This product is intended for the wireless transmission of the doorbell

signal. The product is not intended for commercial use.

Parts and features

Receiver

1

Signal indicator

2

Speaker

3

Signal type selector button

(optical, acoustic, optical and acoustic signal)

4

Melody selection button

5

Volume / Synchronisation button

6

Battery compartment cover

7

Hanger

8

Battery compartment

43150_Funktürklingel_content_GB_IE_SE_DK.indd 10 26.03.14 15:57

11 GB/IE

Transmitter

9

Chime button

10

Name plate

11

Lock hole

12

Holder (for wall mounting)

13

Battery compartment

14

Inner cover

Mounting

15

Rubber cover

16

Screw

17

Dowel

18

Cable exit hole

19

Cable holder

Included items

1 Transmitter

1 Receiver

3 Batteries 1.5 V

, type AA (receiver)

1 Battery 3 V

, type CR2032 (transmitter)

3 Screws (for transmitter and for mounting the receiver on a wall)

3 Dowels

1 Name plate (for the doorbell)

1 Operating instructions

43150_Funktürklingel_content_GB_IE_SE_DK.indd 11 26.03.14 15:57

12 GB/IE

Technical data

Range: 150 m (unobstructed area)

Transmission frequency: 434 MHz

Battery types: Receiver: 3 x 1.5 V

(type AA / LR6),

Transmitter: 1 x 3 V

(type CR2032)

Receiver: Audible signal volume (at maximum

volume setting): app. 73 dB (at a distance

of 1 m from the device)

Ingress protection rating

of the transmitter: IP44 (splash water proof)

Safety

Read all safety information and instructions!

STORE ALL SAFETY INFORMATION AND INSTRUCTIONS IN A

SAFE PLACE IN CASE YOU NEED TO REFER TO THEM AGAIN

IN THE FUTURE!

General safety information

This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental ca-

pabilities or lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

43150_Funktürklingel_content_GB_IE_SE_DK.indd 12 26.03.14 15:57

13 GB/IE

appliance in a safe way and understand the hazards involved.

Children shall not play with the appliance. Cleaning and user

maintenance shall not be made by children without supervision.

Check that all parts are in sound condition. If you use damaged

parts when assembling the device, you risk injury.

Safety instructions for batteries

DANGER TO LIFE! Batteries can be swallowed,

which can prove fatal. Consult a doctor immediately if anyone

swallows a battery.

EXPLOSION HAZARD! Never recharge non-

rechargeable batteries, short-circuit and / or open bat-

teries. This can cause them to overheat, burn or burst.

Never throw batteries into ﬁre or water. The batteries may explode.

Immediately remove depleted batteries from the device; other-

wise there will be an increased risk of leakage!

Always replace all the batteries at the same time and insert

batteries of the same type.

Do not use diﬀerent types of batteries or mix used and new

batteries together.

Batteries do not belong in household refuse. Dispose of used

batteries in an environmentally friendly manner.

Consumers are under a legal obligation to dispose of batteries in

the proper way.

Keep the battery out of the reach of children, do not dispose of

the battery in ﬁre, do not short-circuit it, and do not take it apart.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 13 26.03.14 15:57

14 GB/IE

Failure to observe these instructions may result in the battery dis-

charging beyond its end voltage, which poses a risk of leakage.

If the battery in your instrument has leaked, have it removed im-

mediately to prevent damage to the instrument.

Avoid contact with skin, eyes and mucous membrane. In the event

of contact with battery acid, rinse the aﬀected area with plenty of

water and / or consult a doctor.

Never use rechargeable batteries.

The supply terminals are not to be short-circuited.

Do not mix old batteries with new ones.

Remove the batteries from the device if they have not been used

for a long period.

Make sure you insert the batteries the right way round (polarity).

Assembly

Note: You will need a screwdriver and a drill to assemble the

doorbell.

Note: Only use the screws and dowels supplied for the assembly of

the device.

Mount the receiver (see Fig. D)

Mount the transmitter (see Fig. E)

43150_Funktürklingel_content_GB_IE_SE_DK.indd 14 26.03.14 15:57

15 GB/IE

Preparing for use

Inserting / replacing the batteries

Insert the batteries to provide power to the device before prepar-

ing it for use.

CAUTION! Use the indicated battery types only. Failure to ob-

serve this advice may result in damage to the product.

Receiver (see Fig. B):

Remove the battery compartment cover

6

from the back of the

device.

Remove the used batteries, if present.

Insert 3 batteries (1.5 V

, type AA).

Note: Ensure correct polarity. This is indicated in the battery

compartment

8

.

Close the battery compartment

8

.

Transmitter:

Remove the holder

12

with the help of ﬂat head screw driver

from the back of the transmitter and remove the rubber cover

15

(see ﬁg. C1).

Remove the used batteries, if present (see ﬁg. C2).

Insert a battery (3 V

, type CR 2032). The side marked “+”

must face upwards.

Install the rubber cover

15

, close the holder

12

of the transmitter

back on to the back of the device.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 15 26.03.14 15:57

16 GB/IE

Synchronising transmitter / receiver

The doorbell works on 434MHz which is a quite common frequency.

To ensure that the function gets no inﬂuenced be doorbells in the

neighborhood, the transmitter and the receiver hence have to be syn-

chronized in regard of the encryption. Every transmitter is working

with a diﬀerent encryption of the signal.

Synchronise the transmitter and receiver as follows:

As soon as the batteries are installed, the receiver enters synchro-

nizing mode for app. 1 minute. During the synchronizing mode,

the signal indicator

1

steadily lights up in blue color.

You can also manually enter synchronising mode by holding the

synchronising button

5

for approx. 3 seconds.

The signal indicator

1

on the receiver will steadily light up for

approx. 1 minute, to indicate that the receiver is in synchronizing

mode.

Press the chime button

9

of the transmitter, while the receiver is

in synchronise mode. If the receiver receives the signal, the steady

blue light of the signal indicator

1

ﬂickers 6 times to indicate

that the synchronization is successful.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 16 26.03.14 15:57

17 GB/IE

Setting the signal type

The receiver can indicate the reception of a door signal either both

optically and acoustically, acoustically or optically.

Using the signal type selector button

3

, select whether the

signal is to be indicated both optically and acoustically or acous-

tically or optically.

Press the signal type selector button

3

once. An acoustical

signal will sound up and the afterwards the signal indicator

1

will ﬂash. The receiver will now indicate the door signal acousti-

cally and optically. Press again the signal type selector button

3

.

An acoustical signal will sound. The receiver will now indicate the

door signal acoustically. Press again the signal type selector

button

3

. The receiver will now indicate the door signal in an

optical way.

Setting the volume

Press the volume button

5

until the desired volume is reached.

There are a total of 4 possible volume settings: very loud, loud,

medium, soft.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 17 26.03.14 15:57

18 GB/IE

Selecting the chime

Note: The doorbell has 16 diﬀerent chimes.

Press the melody selection button

4

. The ﬁrst audible signal

sounds.

Press the melody selection button

4

again to move on to the

next audible signal.

Repeat this process until you have selected your desired audible

signal. The last-selected audible signal is automatically stored.

The procedure for connecting the

transmitter to existing bell system or

existing doorbell button

Remove the holder

12

with the help of ﬂat head screw driver

from the back of the transmitter and remove the rubber cover

15

(see ﬁg. C1).

Open the inner cover

14

by cross head screw driver (see ﬁg. F).

Remove the plastic clip of cable exit hole

18

with a ﬂat head

screw driver (see ﬁg. G).

Insert the cable through cable holder

19

and cable exit hole

18

(see ﬁg. H).

Connect cable to A/C terminal (for connecting to existing door-

bell) or B/C terminal (for connecting to existing door bell button)

by using screw driver (see ﬁg. H).

Note: there is no polarity diﬀerent for A or B terminal connect

to C terminal.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 18 26.03.14 15:57

19 GB/IE

Connecting the transmitter

to a existing bell system (see Fig. I)

Extension of an already existing doorbell system:

An already existing doorbell system can be extended with this wire-

less doorbell.

The connection clamps A and C on the backside of the transmitter

must be directly connected with an approx. 50 cm long, 2-wired cord

(bell cord) to the connections of the already existing doorbell system.

The distance between bell and transmitter should be at least 30 to

40 cm.

Note: Contact a qualiﬁed electrician in case of problems during

installation.

Connecting a existing

doorbell button (see Fig. J)

The separate bell button must not be connected to the existing door-

bell system. The battery must remain in the transmitter. The B and C

terminals are to this purpose with a two-core cable connected to the

bell push.

Possibly existing glow / light bulbs must be removed. The doorbell

button is used must be non-illuminated.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 19 26.03.14 15:57

20 GB/IE

Troubleshooting

After the inﬂuence of extraordinary environmental conditions (e.g. a

strong electromagnetical ﬁeld) the function of the item may be af-

fected. In this case, please take oﬀ the batteries of both appliances

for approximately 2 minutes. Then proceed again as described in the

section “Synchronising the transmitter / receiver”.

Electrostatic discharges may lead to malfunctions. If such malfunctions

do occur, remove the battery for a short time and then replace it again.

Then proceed again as described in the section “Synchronising the

transmitter / receiver”.

Cleaning and maintenance

Under no circumstances should you use liquids or detergents, as

these will damage the device.

The device should only be cleaned on the outside with a soft dry

cloth.

Disposal

The packaging is made entirely of recyclable materials,

which you may dispose of at local recycling facilities.

43150_Funktürklingel_content_GB_IE_SE_DK.indd 20 26.03.14 15:57

Page is loading ...

Silvercrest Z32138 Assembly, Operating And Safety Instructions

Silvercrest Z32138 Assembly, Operating And Safety Instructions

in other languages

Related papers

Other documents