Extron PowerCage 401 FOX DR HD User manual

Brand: Extron

Model: PowerCage 401 FOX DR HD

Type: User manual

This manual is also suitable for

PowerCage 401 FOX DT HD

Extron PowerCage 401 FOX DR HD is a modular, compact single slot board that can receive high definition video, audio, and control signals over fiber optic cable. It works together with PowerCage 401 FOX DT HD transmitter and provides extension of HDMI, audio, and RS-232 signals up to 31 miles (50 km) over a single fiber optic cable.

FOX DR HD is compatible with standard fiber optic cables, including multimode and single-mode. It features two independent HDMI video outputs and two independent audio outputs, making it suitable for various applications such as digital signage, video conferencing, and home theater systems.

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

PowerCage

401 FOX DT HD and

PowerCage

401 FOX DR HD • Setup Guide

The Extron PowerCage 401 FOX DT HD Dual Fiber Optic Transmitter and PowerCage 401 FOX DR HD Dual Fiber Optic Receiver

are modular, compact single slot boards for the Extron PowerCage 401. This guide provides instructions for an experienced

installer to install and operate both devices.

CLASS 1 LASER PRODUCT, see the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD User Guide at

www.extron.com

WARNING: Do not look into the rear panel ber optic cable connectors or into the ber optic cables themselves.

AVERTISSEMENT: Ne regardez pas dans les connecteurs de câble bre optique sur le panneau arrière ou dans les câbles

bre optique eux-mêmes.

Installation

Board Installation

Install the transmitter, receiver, or both into a PowerCage 401

enclosure as required.

ATTENTION:

• Use ESD precautions when installing a board to

avoid damaging it. Keep the board in the

anti-static bag until it is needed. Use proper

grounding techniques during installation.

• Prenez les précautions ESD lorsque vous installez

une carte an d’éviter de l’endommager. Gardez la

carte dans le sachet dépoussiérant jusqu’à ce que

vous en ayez besoin. Utilisez des techniques de mise

à la terre correctes pendant l’installation.

NOTES:

• PowerCage boards are hot-swappable.

• Ensure the boards are ush with the rear of the enclosure and the screws are tightened securely before applying power.

• Each slot is independent from other slots. The type of board installed in a slot or the order of slots lled does not impact

boards installed in other slots.

1. If applicable, remove any blank plates or previously installed boards from the PowerCage 401 enclosure to t the board.

2. With the connectors facing away from the PowerCage 401 enclosure and the screws positioned at the top, align the bottom

board edges with the posts of the desired slots on the PowerCage 401 enclosure.

3. Carefully slide the board into the slot and push it rmly into place.

4. Tighten the screws with a tool to secure the board to the enclosure.

Device Connection

RS-232

HDMI

AUDIO AUDIO HDMI

FOX DR HD

Rx Rx

OPTICAL OPTICAL

Tx Tx

SIGNAL

HDCP

Rx GTx

RS-232

Rx GTx

SIGNAL

HDCP

OUTPUTS

RS-232

HDMI

AUDIO AUDIO HDMI

FOX DT HD

Rx Rx

OPTICAL OPTICAL

Tx Tx

SIGNAL

HDCP

Rx GTx

RS-232

Rx GTx

SIGNAL

HDCP

INPUTS

AABB CCDD

EE EEFF

Figure 1. PowerCage 401 FOX DT HD (Left) and PowerCage 401 FOX DR HD (Right) Panels

RS-232

AUDIO

FOX DT HD

SIGNAL

HDCP

RS-232

GTx

SIGNAL

HDCP

OPTICAL

HDMI

OUTPUTS

RS-232

LAN

Rx GTx

REMOTE

RS-232

AUDIO

FOX DT HD

SIGNAL

HDCP

RS-232

Rx G

SIGNAL

HDCP

OPTICAL

HDMI

OUTPUTS

RS-232

AUDIO

FOX DT HD

SIGNAL

HDCP

RS-232

GTx

SIGNAL

HDCP

OPTICAL

HDMI

OUTPUTS

UDIO

AUDIO

FOX DT HD

RS-232

Rx G

SIGNAL

HDCP

TICAL

OPTICAL

HDMI

OUTPUTS

Screws

(2 per board)

Align board and

slide into slot.

HDMI input connectors

Audio input connectors

HDMI output connectors

Audio output connectors

Fiber connectors

RS-232 connectors

68-2659-50 Rev. A

07 16

Inputs and outputs

The PowerCage 401 FOX DT HD includes two independent HDMI video inputs and two independent audio inputs. The

PowerCage 401 FOX DR HD includes two independent HDMI video outputs and two independent audio outputs.

NOTE: Use Extron LockIt

™

Lacing Bracket to secure HDMI cables to the

HDMI connectors (see the image to the right for basic instructions).

1. Connect video inputs or outputs as follows:

• For either input on the transmitter, connect a digital video source to the

HDMI input connector (see ﬁgure 1,

on the previous page).

• For either output on the receiver, connect a digital display to the HDMI

output connector (

2. Connect audio inputs or outputs as follows:

• For unbalanced, stereo audio input, connect an audio source to the 3.5 mm mini stereo

connector (

) for either input on the transmitter.

• To output unbalanced, stereo or mono audio, connect an audio output device to the 3.5 mm mini

stereo connectors (

) for either output on the receiver.

Throughput devices

NOTES:

• Ensure the proper ber cable is used. Typically, singlemode ber optic cables have a yellow jacket

and multimode ber optic cables have an orange or aqua jacket.

• Transmission of HDMI video with HDCP content requires a return ber optic cable from the

receiving device to the transmitting device.

1. Connect a ber cable between the Tx port on the transmitter and the Rx port on the receiver (

on the

previous page and the image to the right).

2. If necessary, connect a ber cable from the Tx port on the receiver to another device in one of the

following methods:

• To return serial data (such as response from a controlled device) to the transmitter, connect a cable

between the Tx port on the receiver and Rx port on the transmitter (see the image to the right).

• To connect up to ten receivers to a transmitter, connect the Tx port on the receiver to the Rx port on

another receiver (see image below) and enable daisy chain mode with SIS commands or the Product

Conguration Software (see the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD User

Guide at www.extron.com).

om Transmitter

or Daisy-Chained

Receiver

Receive

NOTE: Daisy chain mode works with non-HDCP sources only.

3. To pass serial data between a control device and a controlled device (such as control of a projector), connect the desired

type of device to the RS-232 connector on the transmitter or receiver (

). See the PowerCage 401 Enclosure User Guide at

www.extron.com to change the RS-232 protocol. The default RS-232 protocol is as follows:

• 9600 baud • No parity • 8 data bits

• 1 stop bit • No ow control

Operation

After all receivers, transmitters, and their related devices are connected and powered, the system is fully operational. If any

problems are encountered, verify the cables are routed and connected properly and that all display devices have identical

resolutions and refresh rates. If problems persist, call the Extron S3 Sales & Technical Support Hotline.

To congure and control the PowerCage 401 FOX DT HD and PowerCage 401 FOX DR HD, use the Extron Product Conguration

Software, Extron Simple Instruction Set (SIS™) commands, or the internal Web page with the PowerCage 401 enclosure.

Tip (+)

Sleeve ( )

Ring (

)

Tip (+)

Audio Plugs.eps

RCA Connector

3.5 mm Stereo Plug Connector

(balanced)

Sleeve ( )

Ring (R)

Tip (L)

3.5 mm Stereo Plug Connector

(unbalanced)

ransmitter

Receiver

Tx Rx

Extron PowerCage 401 FOX DR HD User manual

Brand: Extron

Model: PowerCage 401 FOX DR HD

Type: User manual

This manual is also suitable for

PowerCage 401 FOX DT HD

Download PDF

report

in other languages

français: Extron PowerCage 401 FOX DR HD Manuel utilisateur

Extron PowerCage 401 FOX DR HD User manual

This manual is also suitable for

Extron PowerCage 401 FOX DR HD User manual

in other languages

Related papers

Other documents