Page is loading ...
I. Getting Started
1.1 Structure
1. Laser light
2. Infrared Night Vision
3. PTT
4. Video Recording
5. Power
6. Voice Recording
7. Taking Camera/White Light Button
2
1
3
4
8
5
6
7
9
15
14
13
12
11
10
18
17
19
16
8. White Light
9. Speaker
10. Menu/Alarm
11. UP
12. DOWN
13. OK/Playback
14. Reset
15. Charging Port
16. Connect External Camera Port
17. Laser Light Button/Night Vision Button
18. USB/HDMI Port
19. Display Screen
1.2 Remote Control Key
Note:
The remote controller is 1 to 1 match the camera, if you buy more than
1 piece of the camera, the remote controllers maybe mixed. If this
happens, you have to match them a pair first to use the remote
controller, the way is: after start the camera, short press the power
button together while press the photo key on remote controller. You
only need to do this when the first time you use them.
5. The Sign on LCD Screen
① Date and Time
② SD Card Storage
③ USER ID
④ Recording Time
⑤ Recording Resolution
⑥ Battery Status
6. Device Charging
Low Battery Prompt: when battery is low, the battery icon in the upper right
corner of the display will turn Red and the flashing " beeps "...... The tone will
automatically shut down after 10 seconds, please charge it in case of low
battery, so as not to affect your use and damage to the battery.
Two Optional Charging：
1 USB Charging Mode ②Docking Station
①Via USB，Charging the Camera Via USB Cable & Wall Charger, The status
of the charging can be reflected from the icon on the LCD (on charging) and
the status indicator (off charging), the LED indicator is red when charging,
the charging indicator is off and the LED indicator is off.
②Via Single Docking Station，Put the Camera into the Docking Station , and
pay attention to the contact and the direction of the charger. The status of the
charging can be reflected from the icon on the LCD (on charging) and the
status indicator (off charging), the LED indicator is red when charging, the
charging indicator is off and the LED indicator is off.
II> Basic Setting
1. Power ON
In the shutdown state, short press “on / off” for 3 seconds,the camera
Boot into the preview screen, LED indicator green.
2. Power OFF
In the boot state, long press the "on / off" button for 3 seconds off, LCD
off, all lights off.
3. Standby
In the boot state, such as "automatic off screen" is turned on, without any
operation boot automatically enter the screen saver mode, the screen is
off, the LED indicator green. Tap any button to light the display.
4. System Setting
Short press "menu" key, enter "setting mode", there are 3 setting modes:
camera mode /Video Recording mode / system setting. After entering a
certain mode interface, click "Up" / "Down" to select the item to be set, click
"OK" to enter the menu to change the setting, click "Up" / " Down "to select
the desired menu, short press" OK "again to save the setting and exit the
menu bar to return to the system setting interface. The device automatically
saves the setting changes.
①Resolution Setting：
Click "OK" to pop up the check box, click "Up" or "Down" to select the
desired resolution, and then click "OK" to confirm.
②DATE&Time Setting：
Click "OK" to pop up the check box, click "Up" or "Down" to select the
desired date and time, select it and click "OK" to confirm.
③Loop Recording：
Click the "OK" button to pop up the check box, click the "Up" or "Down"
button to select the desired video duration, select OK, then click "OK"
button to confirm. (Video segments were: off, 3,5,10 minutes of choice,
the system default 3 minutes, such as the option to turn off the default 15
minutes and do not loop video)
④Picture Resolution Setting：
Click the "OK" button to pop up the check box, click "up" or "down" button
to select the desired resolution, select OK, then click "OK" button to
confirm.
⑤ ID Setting：
Click the "OK" button to pop up the check box, click the "UP" or "DOWN"
button to select the desired ID number, select it, and then click the "OK"
button to confirm.
5. Recording
5.1 Recording
In the power-on state, press the "record" button in the preview screen to start
recording. When the video is recorded, the LED in the upper left corner will
be red and begin to flash slowly, and the green standby light will turn off.
Click the "record" button again to stop recording, LED red light does not flash,
LED green light is always on, the video file is automatically saved to the TF
memory card, the screen automatically returns to the camera preview screen,
and the video is named after the date and time, that MOV suffix, stored in the
memory card. Please refer to the "View / Playback Videos" section for video
review.
5.2 Snap Function
In the process of recording, click the "camera" button 【】 take a picture and
automatically save, in the process will not interrupt the camera function.
6. Taking Camera
In the power-on state, press the "camera" button under the preview screen to
take a photo and automatically save it and return to the photo preview screen.
During the photo-taking process, there is a sound like "click", one photo for
each button, the photo is named after the date and time , JPG suffix, saved in
the memory card. Please refer to the "View / Playback Videos" section for
photos.
7. Recording Alone
On the Power on Station, press "Record" button to start recording alone.
When recording, the screen will display the recording mark, the LED
indicator will blink green, tap "Record" button again to stop recording, LED
will turn green, audio The file is automatically saved on the TF memory card
and the screen automatically returns to the preview screen.
8. Other Function Mode
1
Infrared Night Vision : After switching on the default infrared night vision
light is off, the filter switch for color film, suitable for daytime use. If it is used
at night can press the "laser" button to open the infrared light, filter switch to
switch to white, suitable for night use. Long press the "laser" button to switch
between daytime working mode and night working mode. In the power-on
state, press and hold the "Laser" button to turn on the IR mode. At this time,
the IR LED turns red and the image appears black or white during the
preview or image capture. Press and hold the "Laser" button again to turn off
the IR mode , The infrared light is turned off at this moment, the image in the
preview picture or the photographing process resumes the color image.
2
Laser light function: Click the "laser light / night vision light" laser
positioning light on / off, used to locate the shooting direction.
3
White light function: Long press "camera button / white light button" white
light on / off, for the role of lighting.
④ Explosion warning function: Long press "Menu key / burst key" burst
warning open / closed, used to play a warning role.
9. Delete File
In this unit, can not be individually deleted on the memory card to save any
audio and video files, can only be directly in the menu formatted TF card or
choose to connect the computer inside the computer to delete the desired
content.
10. Check/Playback Video
In the boot state, under the preview Screen, Long press “playback” button to
access playback menu.
①Under this display, tap "Up" or "Down" to select the desired option: Video /
Photo / Voice Recording.
②After selecting the previewed file type (video / photo / voice recording),
press "OK" once to start playing, tap again to pause, long press to exit the
preview interface.
11. Reset Setting
If the device crashes or stops responding due to improper operation or other
special reasons, you can press the reset button to reset the device. After
reset, the device restarts and the device reboots to restore the previous
settings.
12. Indicator light
① In the boot state, the preview screen under the LED lights green, long
bright;
② In the boot state, camera mode LED indicator is red, slowly flashing;③ In
the boot state, the recording mode, the green LED, slowly flashing;
④ When the data connection status, the LED indicator light green long;
⑤ When charging, the LED indicator is red, the LED indicator is off after the
charging is completed;
⑥ At power-on, every time a picture is taken in preview mode, the LED
flashes red once.
13. Connect Computer
Directly connect to the computer, do not have to install any drivers, directly
using the supplied data cable connected to the computer.
14. Remote Controller
The camera has a remote version, you can take pictures and video remote
control operation, convenient, more human.
14.1 Matching Code
After the device is powered on, press and hold the video button for three
seconds, then press the remote control to press the camera button【 】，
The host will take a picture after receiving the signal to indicate the
completion of the code. , Video and other operations.
14.2 Remote Control Button Operation Function：
① 【 】：Taking Camera Button, Press one taking one pic；
② 【■◆】：Video Recording Button, Click it,video Start recording,Click
again,it stop recording
③ 【 ■ 】：Voice Recording button: Press once to start recording and
press again to stop recording
III> Specifications
Chipset: Ambarella A7LA50
Split storage:
5min/10min/20min/30min
Sensor: OV4689
Pre-Record: 20s-85s
Photo: 32M(7552X4248 16:9)
Delay-Record: 10s
(30M/23M/20M/18.5M/16M/4M)
Size: 83mmx60mmx32mm
Video: 2560*1080@30fps
Remote control: available
2304*1296@30fps
Auto IR: menu available
1920*1080@30fps
Vibration: available
1280*720@60fps/30fps
Display: 2.0 inch HD color display
848*480@60fps/30fps
Speaker: available
Storage: 16GB or 32GB option in
a camera
Visual indicators: available
Battery life: 6-8hours
Language: multiple languages
PTT/Walkie-talkie: support, but
needs to customize cable first
from factory
Audio only record: support
Night vision: up to 10 meters
Docking station software: available
Stamp: ID+date+time
Warranty: 1 year
Laser light: available
Battery MSDS: available
White light: available
External button lens: optional
Battery capacity: 2000mAh
Lens angle: 120°
Drop resistant: 2 meters
Waterproof: support
Port
USB, HDMI, AV in, PTT, dock port
IV> Packed accessories
① USB Power Adapter X 1 ⑤ Remote Controller X 1
② USB Cable X 1 ⑥ Docking Station X 1
③ Big Clipper X 1 ⑦ Rechargeable Battery X 1
④ Small Clipper X 1 ⑧ User Manual X 1
V> Trouble Handling
△
!
Equipment can not boot, no response to the operation
1. Please connect the charger to charge the device, check after
charging 2 hours to solve the problem;
2. Please check the charger and the connection cable is normal;
3. Press the reset button to restore the device to factory settings, and
then check whether to solve the problem;
4. If you still can not solve the problem, please contact the sales staff to
return to factory maintenance.
△
!
Red Equipment Picture
The device uses relay control infrared filter lens. When it has been hit in the
course of transportation or fall could lead to an infrared filter lens stuck, the
magnetic force can not be reset after the relay is energized. At this time,
please repeatedly pressing the infrared switch, recovery relay control
infrared filter lens. If not, please shut down after the inverted device, to beat
in a surface is relatively soft place (Arm of the chair, mouse pad etc.). Boot
and check is normal, if not, please contact customer service staff to return
the factory repair.
△!
Device failed to connect computer, and the failure to enter upload
mode
Please contact customer service staff resolved.
△!
Time can not be synchronized
If it can not change the time, please contact customer service staff remote
networking solution.
VI> Note
1. The alarm flash light can only be turned off by long press under the
work mode. If you are in setting mode, you have to exit it by long press
“Playback/OK”button and come back to work mode first, and then can
turn off the light.
2. You can review photos, videos and audios under work mode by long
press the Playback/OK button to enter in, short press it to review, short
press UP or DOWN to select and change among them.
However, you have to connect the camera to computer/tablet first when
you want to delete files, this is for safety reason.
3. When recording video, the screen will automatically shut down for
battery saved, this is not black screen or dead. This is factory default
setting, you could also cancel it in setting mode.
4. Pre-record, delay record, motion detection etc., you have to set first
in respective mode to take effect, when you want to use. Accordingly, if
you don’t need, you should set to off first.
5. To avoid a loss of data stored in the body camera, we recommend
transferring data to your computer/tablet for backup.
6. Charge the camera right away when the battery level is running low.
Let the battery completely drain may damage it.
7. Don’t put the camera into fire or water.
VII> FAQ
Q: What should I do when the camera crashes or gets stuck?
A: The body camera has a special reset button on the left top corner. If the
camera was crashed suddenly, press the button to reset it. The body worn
camera then shut down. And if you press power, it will start again normally.
Q: Can pictures zoom in or out when taking photos?
A: Yes, you can long press up/down button to zoom in or out. Whenever your
hands feel the body vibration, the screen will zoom in / out by one one size.
Q: Is this camera waterproof? Can I use it underwater?
A: It is waterproof IP54, can’t be used underwater but can be used in snowy
and rainy days for outdoor work.
Q: Can this camera's memory card be taken out? Can I fix a larger
memory card in it?
A: Sorry, the memory card is built-in, can not be removed or fixed by
yourself.
/
