2. Troy-Bilt
  3. 31AH64Q4711
31AH64Q4711

Troy-Bilt 31AH64Q4711 Fast Start Guide

  • Hello! I am an AI chatbot trained to assist you with the Troy-Bilt 31AH64Q4711 Fast Start Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I install the chute on the snow thrower?
    How do I adjust the chute control head?
    How do I start the engine?
    What is the recommended fuel for the snow thrower?
    How do I check the oil level?
Upper Handle
A
B
Shift Lever
Chute Control
Chute
Control Rod
778-11822D© 2011 31AH64Q4
Chute
Handle Knobs
Chute Base
Chute Support
Bracket
Chute Control
Head
Place shift lever into F6 A.
position.
Pivot upper handle B.
into operating
position
Tighten handle knobs.C.
A
B
C
Remove cotter pin, wing nut and hex A.
screw from chute control head.
Remove clevis B.
pin and bow-tie
pin from chute
support bracket.
Squeeze the trigger
on the chute control
and rotate the chute
(by hand) to face forward.
The holes in the rear
of the chute control head
will be facing up.
Rotate the chute
control to 1 o’clock,
so the silver arrow
on the pinion gear faces
upward.
Secure the round end of the rod
to the chute control head with the
cotter pin removed in Step 2.
Secure the chute control head
to the support bracket with the
remaining hardware removed
in Step 2.
Insert the hex end of the rod
(hole pointing upward)
into the pinion gear.
Place chute onto chute
base with the chute
control rod positioned
beneath the handle panel.
Reinstall the hex bolt
removed in Step 2 but
do not secure with wing
nut at this time.
Insert the round end of the chute control
rod (hole pointing upward) as far
as possible into the chute control head.
1
4
2
5
3
6
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
Oil Fill /
Dipstick
Electric Starter
Button
Electric
Starter Outlet
Primer
Key
Throttle
Control
Choke
Control
Gas Fill
Move throttle control into
the Fast
position.
Move the choke control
into the Choke
position.
Connect power cord to A.
electric starter outlet.
Plug other end of power B.
cord into a three-prong
120-volt, grounded, AC
receptacle.
Push primer
three times.
Fill fuel tank with clean,
fresh gasoline. Do not fill
above the base of fuel
tank neck.
Check the oil level using
the dipstick. Add oil if
necessary. (Refer to the
Operator’s Manual)
Insert the key into
the key switch until
the key snaps into
place.
Do not turn the key!
To start engine, push A.
the starter button.
When engine starts, B.
slowly move choke
control into the Run
position.
Disconnect cord from C.
power receptacle
first and then from
snow thrower’s
outlet.
778-11822D© 2011 31AH64Q4
7
10
8
11
9
12
READ AND UNDERSTAND ALL INSTRUCTION, WARNING, AND DANGER LABELS.
PARA INSTRUCCIONES EN ESPAÑOL, REFIÉRASE AL MANUAL DEL OPERADOR.
IMPORTANT: READ OPERATOR'S MANUAL AND ENGINE MANUAL THOROUGHLY
AND FOLLOW THE IMPORTANT SAFE OPERATION PRACTICES BEFORE OPERATING .
Need Help? Call 1-888-TO-HELP-U
/