Kichler Lighting 35170 User manual

ITEM #0577412

MODEL #35170

CEILING FAN

1

Kichler® is a registered trademark of

ATTACH YOUR RECEIPT HERE

Serial Number

Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.

Français p. 18

Español p. 35

PACKAGE CONTENTS

2

A

Hanging Bracket

Down Rod

Canopy

Blade Iron

Motor Coupling Cover

Motor Assembly

B

C

D

E

F

1

5

1

PART DESCRIPTION QTY

Light Kit Housing

Light Kit

5-Watt LED type-A15 Bulb

Diffuser

Blade

G

H

I

J

K

1

2

1

5

PART DESCRIPTION QTY

A

K

C

I

E

G

B

D

F

J

H

HARDWARE CONTENTS

3

Balance Kit

SAFETY INFORMATION

Hanging bracket Screw

Hanging bracket Washer

Blade Iron Screws

Flat Washer + Spring Washer

Wire Connector

Blade Screw

HARDWARE BAG REMOTE CONTROL

Remote Control

Remote Control Holder

Receiver

Battery

Wood Screw

Lag Screw

Wire Connector

Please read and understand this entire manual before attempting to assemble, operate or install the

product. If you have any questions regarding the product, please call customer service at

1-800-554-6504, 8 a.m. - 4:30 p.m., EST.

WARNING:

• Important: When using an existing outlet box, be sure the box is securely attached to the building

structure and can support the full weight of the fan. Failure to do so can result in serious injury or

death.

• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to

disconnect power supply prior to installation may result in serious injury or death.

• Warning - Connecting this fan to a light switch (on/off) has been known to cause damage to the

receiver. This fan must be wired to continually receive power. Failure to do so will drastically

reduce the lifespan of this fan.

• Do not install fan on a ceiling with a pitch greater than 20°.

• WARNING – To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box

Marked 'Acceptable for Fan Support of 15.9 kg (35 lbs) or less' And Use Mounting Screws

Provided With The Outlet Box and/or Support Directly From Building Structure. Most Outlet Boxes

Commonly Used For The Support of Luminaires Are Not Acceptable For Fan Support And May

Need To Be Replaced. Consult A Qualified Electrician If In Doubt."

• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.

PREPARATION

WARNING (continued)

4

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.

Contact customer service for replacement parts.

Estimated assembly time: 30 minutes to 1 hour.

Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,

electrical tape, ladder, safety glasses.

• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of

the blades.

• To reduce the risk of fire or electrical shock, do not use this fan with any solid state fan speed

device or variable speed control.

A B C

ASSEMBLY INSTRUCTIONS

• WARNING-To reduce risk of fire, electric shock, or personal injury, mount to outlet box marked

“Acceptable for Fan Support of 15.9kg (35lbs) or less” and use mounting screws provided with the

outlet box and/or support directly from building structure. Most outlet boxes commonly used for

the support of luminaries are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly

supported from a structural framing member of a building and (see examples in figures A & B) or

may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) to 15.9kg

(35 lbs) (see example in figure C).

ASSEMBLY INSTRUCTIONS

5

1. Secure the hanger bracket (A) to the ceiling outlet

box using hanging bracket screws and hanging

bracket washers.

Important: If attaching the fan to a sloped ceiling,

make sure open end of mounting bracket is installed

facing the roof. Do not install fan on a ceiling with a

pitch greater than 20°.

1

A

Outlet Box

Hardware Used

x 2

Hanging Bracket

Screw

Hanging Bracket

Washer

ASSEMBLY INSTRUCTIONS

6

2. Loosen the set screws found on coupling on top of

the motor assembly (F). Then remove the hair and

clevis pin that will be used on a later step.

3. Insert down rod (B) through canopy (C), and motor

coupling cover (E). Feed wires from the motor

assembly (F) through the down rod (B), then insert

the down rod (B) into the coupling found on top of

the motor assembly (F).

2

F

Hair Pin

Safety Cable

Clevis Pin

Coupling

F

3

C

E

B

ASSEMBLY INSTRUCTIONS

7

5. Carefully lift the fan and seat the downrod (B)/hanger

ball assembly on the hanger bracket (A). Be sure the

groove in the ball is lined up with the tab on the

hanger bracket (A).

4. Pass the clevis pin through the down rod (B) and

coupling found on the motor assembly (F) then

secure with the hair pin. Tighten set screws found

on the coupling on the motor assembly (F).

Hair Pin

Clevis Pin

Coupling

B

F

4

B

A

5

8

ASSEMBLY INSTRUCTIONS

6. For Canadian installation and for USA fans over 35

lbs, the safety cable must be installed into the house

structure beams using a 3” lag screw. Make sure

that when the safety cable is fully extended the lead

wires are longer than the cable and no stress is

placed on the lead wires.

Safety

Cable

Lag

Screw

Safety

Cable

Flat

Washer

Spring

Washer

6

Safety

Cable

Hardware Used

x 1

Lag Screw

Flat Washer

Spring Washer

ASSEMBLY INSTRUCTIONS

9

7. Wiring the fan per wiring diagram and securely connect wires with wire connectors: Wrap

electrical tape (not included) around each wire connector and make sure no bare wire or wire

strands are visible after making connections.

• Connect WHITE wire from the fan to WHITE wire marked TO MOTOR N from the receiver.

• Connect BLUE wire from the fan to BLUE wire marked FOR LIGHT from the receiver.

• Connect BLACK wire from the fan to BLACK wire marked TO MOTOR L from the receiver.

• Connect BLACK wire from the outlet box to BLACK wire marked AC IN L from the receiver.

• Connect WHITE wire from the outlet box to WHITE wire marked AC IN N from the receiver.

• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN

or BARE COPPER) from house.

7

OUTLET BOX

BLACK

(LIVE)BLACK

WHITE

(NEUTRAL)

WHITE

(NEUTRAL)

WHITE

BARE COPPER

(GROUND)

GREEN (BRACKET)

GREEN (DOWN ROD)

BLUE (LIGHT)

BLACK (MOTOR) BLACK

BLUE

Hardware Used

x 6Wire Connector

ASSEMBLY INSTRUCTIONS

10

9. Once wiring step has been completed, slide the

wired remote receiver in between the hanging

bracket (A) and the top of the downrod ball (B) with

the flat side of the receiver facing the ceiling. Turn

lead wires upward and carefully push them into the

outlet box, with the white and green wires to one

side of the box and the black wires toward the other

side.

9

A

B

8. There are 16 combinations of code for setting up the

remote control. If you do not use the dip switch set

up by manufacture then you will need to use the set

up procedures listed below.

Remove the remote control battery cover to expose

the remote dip switches. Use a small ballpoint pen

(not included) to set the dip switches to either up or

down.

a.) Install the 23A 12V battery (included) and replace the

battery cover you previously removed.

b.) After installing the unit and restoring power to the

fan, press and hold the “Light” button until the light

flashes (on/off) 3 times and will stay on, then the

control and speed setting process is complete. You

must press the “Light” button within 30 seconds of

restoring power to the fan.

c.) If programming is unsuccessful, retry the above

instructions.

The remote control comes with a cradle that may be

attached to the wall with the included screws.

REMOTE

CONTROL

8

RECEIVER

NOTE: Remove batteries if remote has

not been used for a long period of time

in order to avoid damage. Store remote

away from excessive heat or humidity.

ASSEMBLY INSTRUCTIONS

11

12. Insert blade iron (D) into slot on the motor assembly

(F). Align the holes on the blade iron (D) with the

holes on the blade holder and secure with the 3

blade iron screws from the hardware bag.

Repeat for remaining blade assemblies

10.Remove two canopy screws that align with the round holes on the canopy (C) and loosen the

other two canopy screws making sure not to remove them. Raise canopy (C) over the hanging

bracket (A) aligning the screws that remained into the canopy (C). Twist canopy (C) clockwise to

secure. Reinstall the two screws that were previously removed into the holes on the canopy (C).

Tighten all screws.

C

A

10

A

C

11

D

K

11. Attach blade iron (D) to blade (K) with blade screws.

Do not tighten blade screws until each screw has

been started. Then, tighten each screw starting with

the center screw.

Repeat for remaining blades

F

D

12

Hardware Used

x 15Blade Screw

Hardware Used

x 10Blade Iron Screw

ASSEMBLY INSTRUCTIONS

12

13. Remove the mounting screw marked with a red dot label from the motor assembly (F) and loosen

but do not remove the other 2. Feed the wires from the motor assembly (F) through the center

hole in the light kit housing (G). Position keyhole slots around the screws and twist clockwise.

Insert the screw that you had previously removed. Tighten all screws.

13

F

G

ASSEMBLY INSTRUCTIONS

13

14.Connect wires from the motor assembly (F) to the light kit (H). Remove 1 of 3 screws from the

light kit housing (G) and loosen the other 2. Position keyhole slots around the screws and twist

clockwise. Insert the screw that you had previously removed. Tighten all screws.

Note: White wire connects to white wire and black wire connects to black wire.

H

G

14

F

I

H

15

CAUTION: An energy-saving wattage limiter is

included in the receiver of the fan. When replacing

bulbs, ensure bulb wattage is below 190 watts,

otherwise the item will not function.

WARNING: To reduce risk of burns, eye damage, or

electrical shock, disconnect power and allow bulb to

cool for at least 5 minutes before replacing. Do not

touch the bulb or look directly at the lamp when in

use. Replace glass/shade/diffuser if broken.

15. Insert LED bulbs (I) into the socket found on the

light kit (H). When necessary, replace with bulbs of

the same wattage.

ASSEMBLY INSTRUCTIONS

14

16.Raise diffuser (J) to the light kit housing (G). Once in place turn the diffuser (J) clockwise to lock

into place.

16

G

J

Remove remote battery door, connect battery (included) with plug pressing the battery inside and

replace the battery door. If not used for long periods of time, remove the battery to prevent

damage to the transmitter.

Fan control :

Low speed

Medium speed

High speed

To turn off the fan

Press light key quickly to turn light on or off

OPERATION

For DIMMER function: press and hold button to dim the light. The light will cycle from bright to

dim to bright until button is released. Light will maintain last setting if turned off.

This remote has a memory function. The remote stores the fan speed and light setting when the

fan is turned off. When the fan is turned on again, it starts with the most recent setting.

Low

Speed

Fan

Off

Medium Speed

High

Speed

Light

On / Off

Use the fan reversing switch to optimize your fan for seasonal performance.

Note: Wait for fan to stop before reversing the switch.

• In warmer weather, counterclockwise movement of the fan will result in downward airflow

creating a wind chill effect. Push switch to the left.

• In cooler weather, clockwise movement of the fan will result in upward airflow that can help move

stagnant hot air off the ceiling area. Push switch to the right.

15

OPERATION (continued)

STEPS TO BALANCING THE CEILING FAN

• Tighten screws on the mounting bracket, outlet box, the downrod , fan blades to blade holders,

and blade holders to the motor housing.

• Measure the distance from the tip of each blade to the ceiling. All blades should have the same

vertical distance from the ceiling. Adjust any bent blade holder, by gently pressing up or down on

the brackets, until all blades are at an equal distance from the ceiling.

If wobbling persists, you may need a blade balancing kit to stabilize the ceiling fan. A blade

balancing kit consists of a plastic clip and two balancing weights.

Determining the blade that needs to be balanced is a trial-and-error task.

1. Place a numbered piece of masking tape on each blade so you don't lose track of which blade is

which.

2. One blade at a time, attach the slotted plastic clip over the center of the blade edge and turn the

fan on. Observe which blade has the clip on when the ceiling fan wobbles the least.

3. Place the plastic clip on the edge of the blade, halfway between the blade holder and the blade

tip. Turn fan on and determine improvement.

4. If there is no improvement, turn off the fan again. Slide the clip along the length of the blade to

locate the source of instability.

5. Once you've found the faulty blade, press a balancing weight on the centerline. The weight

should be parallel to the clip.

Reverse Switch

16

CARE AND MAINTENANCE

At least twice a each year tighten all screws and lower canopy to check mounting bracket screws

and downrod assembly. Clean fan housing with only a soft brush or lint free cloth to avoid

scratching the finish. Clean blades with a lint free cloth. Shut off main power supply before

beginning any maintenance. Do not use water or a damp cloth to clean the ceiling fan.

STEPS TO BALANCING THE CEILING FAN (continued)

FCC WARNING

Balancing Weight

Plastic Clip

5G

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna, increase the separation between the equipment and

receiver, and connect the equipment into an outlet on a circiut different from that to which the fan is

connected.

17

WARRANTY

Rev. 05-30-18

Kichler offers the following limited lifetime warranty to the Original Purchaser of a Kichler Ceiling Fan:

if the Fan’s motor or motor-related parts should fail due to what Kichler, in its sole discretion,

determines to be a defect in material or workmanship, Kichler will, at its option, either repair or

replace the defective part free of charge.

Except as provided below, for one (1) year following the purchase date, if any part other than the

motor or motor-related parts, including, but not limited to, blades, light kits, downrods, switches,

housing, or finish should fail due to what Kichler, in its sole discretion, determines to be a defect in

material or workmanship, Kichler, at its option, will repair or replace the defective part free of charge.

To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly

defective parts or products to the authorized Kichler distributor that the product was purchased from

with PROOF OF PURCHASE, Original Purchaser’s name and return address and a description of the

claimed product defect.

If any of the warranted products are found by Kichler, in its sole discretion, to be defective, such

products will, at Kichler’s sole option and cost, be replaced, repaired or refunded less an amount

directly attributable to Original Purchaser’s prior use of the product. Kichler will return the repaired or

replaced product prepaid freight. This warranty does not cover labor or other costs or expenses to

remove or install any defective, repaired or replaced product.

The parties hereto expressly agree that Original Purchaser’s sole and exclusive remedy against

Kichler shall be for the repair, replacement or refund of defective products as provided herein. This

warranty extends only to product ownership by the Original Purchaser; is not transferable whether to

heirs, subsequent owners, or otherwise; and is void if the Original Purchaser ceases to own the

product.

This warranty does not apply to any products that have been subjected to misuse, mishandling,

misapplication, connected to voltage at more than 5% above standard North American voltage,

unusual use (including but not limited to use in an environment where the annual average ambient

operating temperature is below 27 or above 95 degrees Fahrenheit), neglect (including but not limited

to improper maintenance), accident, acts of god such as high winds, improper installation or care,

failure to follow the Product’s written instructions for normal use and care, improper packaging of

products returned to Kichler, modification (including but not limited to use of unauthorized parts or

attachments), or adjustment or repair. Significant product exposure to chemicals, harsh cleaners, salt

water or salt air will void any and all warranties on exterior finishes. This warranty only applies when

all components, including transformers, have been provided by Kichler. Substituting another

manufacturer’s product and/or components will render the warranty completely void.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER

RIGHTS, WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS

ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS

MAY NOT APPLY TO YOU.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR

PURPOSE OR INFRINGEMENT. ORIGINAL PURCHASER SHALL IN NO EVENT BE ENTITLED

TO, AND KICHLER LIGHTING SHALL NOT BE LIABLE FOR, INDIRECT, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES OF ANY NATURE, INCLUDING, BUT NOT LIMITED TO LOSS

OF PROFIT, PROMOTIONAL AND/OR MANUFACTURING EXPENSES, OVERHEAD, INJURY TO

REPUTATION AND/OR LOSS OF CUSTOMERS.

Page is loading ...

Kichler Lighting 35170 User manual

Kichler Lighting 35170 User manual

in other languages

Related papers

Other documents