Français p. 17
Español p. 33
ITEM #0803773
MODEL #35156
CEILING FAN
1
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
Kichler® is a registered trademark of
The L.D. Kichler Co. All Rights Reserved.
PACKAGE CONTENTS
2
A
Hanging Bracket
Down Rod
Canopy
Blade
Motor Coupling Cover
B
C
D
E
1
1
1
5
1
PART DESCRIPTION QTY
Motor Assembly
Light Kit Housing
Light Kit
Blade Iron
LED Bulb
G
F
H
I
J
1
1
1
5
3
PART DESCRIPTION QTY
A
F
C
H
E
B
G
J
I
D
HARDWARE CONTENTS
3
SAFETY INFORMATION
Hanging bracket Screw
Hanging bracket Washer
Wire Connector
Blade Screw
HARDWARE BAG REMOTE CONTROL
Remote Control and Receiver
Remote Control Holder
Battery
Screws
Wood Screw
Lag Screw
Blade Iron Screws
Shade Screws
Flat Washer + Spring Washer
Please read and understand this entire manual before attempting to assemble, operate or install the
product. Save this manual when finished.
WARNING:
• Important: When using an existing outlet box, be sure the box is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury or
death.
• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to
disconnect power supply prior to installation may result in serious injury or death.
• Warning - Connecting this fan to a light switch (on/off) has been known to cause damage to the
receiver. This fan must be wired to continually receive power. Failure to do so will drastically
reduce the lifespan of this fan.
• Do not install fan on a ceiling with a pitch greater than 20°.
• WARNING – To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked 'Acceptable for Fan Support of 15.9 kg (35 lbs) or less' And Use Mounting Screws
Provided With The Outlet Box and/or Support Directly From Building Structure. Most Outlet Boxes
Commonly Used For The Support of Luminaires Are Not Acceptable For Fan Support And May
Need To Be Replaced. Consult A Qualified Electrician If In Doubt."
• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.
• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of
the blades.
Balance Kit
WARNING (continued)
CAUTION:
PREPARATION
4
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated assembly time: 30 minutes to 1 hour.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, safety glasses.
A B C
ASSEMBLY INSTRUCTIONS
• WARNING-To reduce risk of fire, electric shock, or personal injury, mount to outlet box marked
“Acceptable for Fan Support of 15.9kg (35lbs) or less” and use mounting screws provided with the
outlet box and/or support directly from building structure. Most outlet boxes commonly used for
the support of luminaries are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly
supported from a structural framing member of a building and (see examples in figures A & B) or
may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) to 15.9kg
(35 lbs) (see example in figure C).
• To reduce the risk of fire or electrical shock, do not use this fan with any solid state fan speed
device or variable speed control.
• Do not touch hot LED
• The LED light output is strong enough to injure human eyes. Precautions must be taken to
prevent looking directly at the LEDs with unaided eyes for more than a few seconds.
• Read and understand all instructions and illustrations completely before proceeding with assembly
and installation of this fixture.
• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate
completely, please contact a qualified licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts
out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate
the UL listing, C.S.A. certification, and/or UL listing of this fixture.
• This fixture is intended for installation in accordance with the National Electric Code (NEC) and all
local code specifications.
• Use ONLY the supplied LED driver to power fixture.
• Driver cable is not intended for use through or concealed behind walls, floors, or ceilings.
ASSEMBLY INSTRUCTIONS
5
1.
Turn off the circuit breaker to the fan supply line
leads.
DANGER: Failure to disconnect power supply prior
to installation may result in serious injury or death.
3. Loosen the set screws found on the coupling on top
of the motor assembly (F). Then, remove the
preassembled hair and clevis pin and save for later
use.
2. Secure the hanging bracket (A) to the ceiling outlet
box using hanging bracket screws and hanging
bracket washers.
Important: If attaching the fan to a sloped ceiling,
make sure open end of mounting bracket is installed
facing the roof. Do not install fan on a ceiling with a
pitch greater than 20°.
2
A
Outlet Box
Hanging
Bracket
Washer
Hanging
Bracket
Screw
3
F
Clevis Pin
Hair Pin
20 20
OFF
OFF
OFF
100
1
6
ASSEMBLY INSTRUCTIONS
4. Insert downrod (B) through canopy (C) and motor
coupling cover (E).
5.
Feed wires from the motor assembly (F) through the
downrod (B), then insert the downrod (B) into the
coupling found on top of the motor assembly (F).
4a
4b
B
B
C
C
E
5
B
F
Motor
Coupling
7
ASSEMBLY INSTRUCTIONS
6. Pass the previously removed clevis pin through the
downrod (B) and coupling of motor assembly (F),
then secure with previously removed hair pin.
Re-tighten set screws on the coupling and lower the
motor coupling cover (E).
7.
Carefully lift the fan and seat the ball of the downrod
(B) in the hanger bracket (A). Be sure the groove in
the ball is lined up with the tab on the hanger bracket
(A).
DANGER: Be careful when aligning the tab to
the groove in ball. If not fully engaged, there is a
possibility of the fan falling, which may result in
serious injury or death.
7
A
B
6
B
E
F
ASSEMBLY INSTRUCTIONS
8
8. For Canadian installation and for USA fans over 35
lbs, the safety cable must be installed into the house
structure beams using a 3” lag screw. Make sure
that when the safety cable is fully extended the lead
wires are longer than the cable and no stress is
placed on the lead wires.
Safety
Cable
Lag
Screw
Safety
Cable
Flat
Washer
Spring
Washer
8
Safety
Cable
9
REMOTE CONTROL
RECEIVER
9. In order to use this remote control the dip switches
must match on both the remote control and the
receiver. Make sure they both have the same
configuration.
Remove the battery cover from the remote control.
Slide dip switches up or down using a small screw
driver (not included). Then match the dip switches
on the receiver to the same position as the remote
control.
Install the battery (included) and replace the battery
cover you previously removed.
ASSEMBLY INSTRUCTIONS
9
10. Wiring the fan per wiring diagram and securely connect wires with wire connectors: Wrap
electrical tape (not included) around each wire connector and make sure no bare wire or wire
strands are visible after making connections.
• Connect WHITE wire from the fan to WHITE wire marked TO MOTOR N from the receiver.
• Connect BLUE wire from the fan to BLUE wire marked FOR LIGHT from the receiver.
• Connect BLACK wire from the fan to BLACK wire marked TO MOTOR L from the receiver.
• Connect BLACK wire from the outlet box to BLACK wire marked AC IN L from the receiver.
• Connect WHITE wire from the outlet box to WHITE wire marked AC IN N from the receiver.
• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN
or BARE COPPER) from house.
GREEN or
GREEN
BARE COPPER
Receiver
BLUE (Light)
BLACK (Motor)
WHITE (Neutral)
BLUE
BLACK
WHITE
10
WHITE
(Neutral)
BLACK
(Live)
WHITE
(AC Input)
BLACK
(AC Input)
Outlet Box
ASSEMBLY INSTRUCTIONS
10
11. Once wiring step has been completed, slide the
wired remote receiver in between the hanging
bracket (A) and the top of the downrod ball (B) with
the flat side of the receiver facing the ceiling. Turn
lead wires upward and carefully push them into the
outlet box, with the white and green wires to one
side of the box and the black wires toward the other
side.
12. Loosen one of the shoulder screws without fully
removing it from the hanging bracket (A).
Completely remove the remaining shoulder screw
from the hanging bracket (A).
Assemble canopy (C) by rotating keyhole slot on
canopy (C) over shoulder screw in hanging bracket
(A). Loosely screw the previously removed shoulder
screw into the canopy and onto hanging bracket (A).
Tighten shoulder screws. Securely attach and tighten
the canopy hole cover over the shoulder screws in
the hanging bracket (A) utilizing the keyhole slot
twist-lock feature.
11
A
B
13
I
D
Blade
Screw
13. Attach blade iron (I) to blade (D) with blade screws.
Do not fully tighten blade screws until each screw
has been started. Then, tighten each blade screw
starting with the center screw. Repeat for remaining
blade irons (I) and blades (D).
12
C
A
Shoulder
Screw
Canopy
Hole
Cover
Shoulder
Screw
ASSEMBLY INSTRUCTIONS
11
14. Attach blade irons (I) to the underside of the motor
assembly (F) with the blade iron screws.
15.
Remove the preassembled mounting screws
from the motor assembly (F).
I
F
Blade Iron
Screws
14
G
F
15
Feed the wires from the motor assembly (F) through
the center hole in the light kit housing (G).
Re-install
the previously removed mounting screws through
light kit housing (G) to the motor assembly (F), then
tighten all screws securely.
ASSEMBLY INSTRUCTIONS
12
16.Remove the preassembled screws from the inside of
the light kit housing (G).
17.Install LED bulbs (J) into the sockets found on light
kit (H).
Connect wires from the motor assembly (F) to the
light kit (H) - WHITE to WHITE and BLACK to
BLACK.
Position slots on light kit (H) to the slots from the
previously removed screws found on the light kit
housing (G). Re-install the previously removed
screws and tighten securely.
16
H
G
H
J
17
Fan control :
Low: Low speed
Med: Medium speed
High: High speed
Off: To turn off the fan
Turns the light ON and OFF
as well as controlling the brightness setting.
OPERATION
13
The remote control comes with a base that may be
mounted to the wall with the included screws. The
half-circle tab on the base slides into a small lip on
the back of the remote.
NOTE: Remove batteries if remote has
not been used for a long period of time
in order to avoid damage. Store remote
away from excessive heat or humidity.
Low
Speed
Fan
Off
Medium Speed
High
Speed
Light
On / Off
14
Balancing Weight
Plastic Clip
5G
• Tighten screws on the mounting bracket, outlet box, the downrod , fan blades to blade holders,
and blade holders to the motor housing.
• Measure the distance from the tip of each blade to the ceiling. All blades should have the same
vertical distance from the ceiling. Adjust any bent blade holder, by gently pressing up or down on
the brackets, until all blades are at an equal distance from the ceiling.
If wobbling persists, you may need a blade balancing kit to stabilize the ceiling fan. A blade
balancing kit consists of a plastic clip and two balancing weights.
Determining the blade that needs to be balanced is a trial-and-error task.
1. Place a numbered piece of masking tape on each blade so you don't lose track of which blade is
which.
2. One blade at a time, attach the slotted plastic clip over the center of the blade edge and turn the
fan on. Observe which blade has the clip on when the ceiling fan wobbles the least.
3. Place the plastic clip on the edge of the blade, halfway between the blade holder and the blade
tip. Turn fan on and determine improvement.
4. If there is no improvement, turn off the fan again. Slide the clip along the length of the blade to
locate the source of instability.
5. Once you've found the faulty blade, press a balancing weight on the centerline. The weight
should be parallel to the clip.
STEPS TO BALANCING THE CEILING FAN
Balance Kit
15
CARE AND MAINTENANCE
REVERSE
At least twice a each year tighten all screws and lower canopy to check mounting bracket screws
and downrod assembly. Clean fan housing with only a soft brush or lint free cloth to avoid
scratching the finish. Clean blades with a lint free cloth. Shut off main power supply before
beginning any maintenance. Do not use water or a damp cloth to clean the ceiling fan.
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and
receiver, and connect the equipment into an outlet on a circiut different from that to which the fan is
connected.
Use the fan reversing switch to optimize your fan for seasonal performance.
Note: Wait for fan to stop before reversing the switch.
• In warmer weather, counterclockwise movement of the fan will result in downward airflow
creating a wind chill effect. Push switch to the left.
• In cooler weather, clockwise movement of the fan will result in upward airflow that can help move
stagnant hot air off the ceiling area. Push switch to the right.
16
WARRANTY
Rev. 08-12-16
Kichler Lighting warrants that its products will be free from defects in material and workmanship for
one (1) year from the date of purchase by the Original Purchaser.
To replace a product that has a warranted defect, the Original Purchaser shall return any allegedly
defective parts or products to the authorized Kichler distributor that the product was purchased from
with PROOF OF PURCHASE, Original Purchaser’s name and return address and a description of the
claimed product defect.
If any of the warranted products are found by Kichler, in its sole discretion, to be defective, such
products will, at Kichler’s sole option and cost, be replaced, repaired or refunded less an amount
directly attributable to Original Purchaser’s prior use of the product. Kichler will return the repaired or
replaced product prepaid freight. This warranty does not cover labor or other costs or expenses to
remove or install any defective, repaired or replaced product.
The parties hereto expressly agree that Original Purchaser’s sole and exclusive remedy against
Kichler shall be for the repair, replacement or refund of defective products as provided herein. This
warranty extends only to product ownership by the Original Purchaser; is not transferable whether to
heirs, subsequent owners, or otherwise; and is void if the Original Purchaser ceases to own the
product.
This warranty does not apply to any products that have been subjected to misuse, mishandling,
misapplication, connected to voltage at more than 5% above standard North American voltage,
unusual use (including but not limited to use in an environment where the annual average ambient
operating temperature is below 27 or above 95 degrees Fahrenheit), neglect (including but not limited
to improper maintenance), accident, acts of god such as high winds, improper installation or care,
failure to follow the Product’s written instructions for normal use and care, improper packaging of
products returned to Kichler, modification (including but not limited to use of unauthorized parts or
attachments), or adjustment or repair. Significant product exposure to chemicals, harsh cleaners, salt
water or salt air will void any and all warranties on exterior finishes. This warranty only applies when
all components, including transformers, have been provided by Kichler. Substituting another
manufacturer’s product and/or components will render the warranty completely void.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS
MAY NOT APPLY TO YOU.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR
PURPOSE OR INFRINGEMENT. ORIGINAL PURCHASER SHALL IN NO EVENT BE ENTITLED
TO, AND KICHLER LIGHTING SHALL NOT BE LIABLE FOR, INDIRECT, SPECIAL, INCIDENTAL
OR CONSEQUENTIAL DAMAGES OF ANY NATURE, INCLUDING, BUT NOT LIMITED TO LOSS
OF PROFIT, PROMOTIONAL AND/OR MANUFACTURING EXPENSES, OVERHEAD, INJURY TO
REPUTATION AND/OR LOSS OF CUSTOMERS.
Printed in China
Kichler® is a registered trademark of
The L.D. Kichler Co. All Rights Reserved
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
