ONKYO C-7030 User manual

Brand: ONKYO

Model: C-7030

Category: CD players

Type: User manual

This manual is also suitable for

C-7030C-7070C7030 NOIR

COMPACT DISC PLAYER

C-7030

Instruction Manual

Thank you for purchasing an Onkyo product. Please read this

manual carefully before making any connections or using this

product. By following these instructions, you’ll get the best audio

performance and the most listening pleasure from your Onkyo

product. Keep this manual for future reference.

Getting Started

............................En-2

Connections

.............................. En-13

Basic Operation

....................... En-15

Disc Playback

........................... En-16

Various Playback Modes

..... En-21

Setting for MP3/WMA

............ En-24

Troubleshooting

...................... En-26

Specifications

........................... En-27

En-2

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radia-

tors, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are pro-

vided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience recepta-

cles, and the point where they exit from the appara-

tus.

11. Only use attachments/accessories specified by the

manufacturer.

12.

Use only with the cart, stand,

tripod, bracket, or table spec-

ified by the manufacturer, or

sold with the apparatus.

When a cart is used, use cau-

tion when moving the cart/

apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

15. Damage Requiring Service

Unplug the apparatus from the wall outlet and refer

servicing to qualified service personnel under the

following conditions:

A. When the power-supply cord or plug is damaged,

B. If liquid has been spilled, or objects have fallen

into the apparatus,

C. If the apparatus has been exposed to rain or

water,

D. If the apparatus does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions as an improper adjustment of other

controls may result in damage and will often

require extensive work by a qualified technician

to restore the apparatus to its normal operation,

E. If the apparatus has been dropped or damaged in

any way, and

F. When the apparatus exhibits a distinct change in

performance this indicates a need for service.

16. Object and Liquid Entry

Never push objects of any kind into the apparatus

through openings as they may touch dangerous volt-

age points or short-out parts that could result in a

fire or electric shock.

The apparatus shall not be exposed to dripping or

splashing and no objects filled with liquids, such as

vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of

this unit.

17. Batteries

Always consider the environmental issues and fol-

low local regulations when disposing of batteries.

18. If you install the apparatus in a built-in installation,

such as a bookcase or rack, ensure that there is ade-

quate ventilation.

Leave 20 cm (8") of free space at the top and sides

and 10 cm (4") at the rear. The rear edge of the shelf

or board above the apparatus shall be set 10 cm (4")

away from the rear panel or wall, creating a flue-

like gap for warm air to escape.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

AVIS

PORTABLE CART WARNING

S3125A

En-3

Precautions

1. Recording Copyright—Unless it’s for personal use

only, recording copyrighted material is illegal with-

out the permission of the copyright holder.

2. AC Fuse—The AC fuse inside the unit is not user-

serviceable. If you cannot turn on the unit, contact

your Onkyo dealer.

3. Care

—Occasionally you should dust the unit all over

with a soft cloth. For stubborn stains, use a soft cloth

dampened with a weak solution of mild detergent and

water. Dry the unit immediately afterwards with a

clean cloth. Don’t use abrasive cloths, thinners, alco-

hol, or other chemical solvents, because they may

damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SEC-

TION CAREFULLY.

AC outlet voltages vary from country to country.

Make sure that the voltage in your area meets the

voltage requirements printed on the unit’s rear panel

(e.g., AC 230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit

from the AC power source. Make sure that the plug

is readily operable (easily accessible) at all times.

Pressing the [ON/STANDBY] button to select

Standby mode does not fully disconnect from the

mains. If you do not intend to use the unit for an

extended period, remove the power cord from the

AC outlet.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and head-

phones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed) shall

not be exposed to excessive heat as sunshine, fire or

the like.

7. Never Touch this Unit with Wet Hands—Never

handle this unit or its power cord while your hands

are wet or damp. If water or any other liquid gets

inside this unit, have it checked by your Onkyo

dealer.

8. Handling Notes

• If you need to transport this unit, use the original

packaging to pack it how it was when you origi-

nally bought it.

• Do not leave rubber or plastic items on this unit

for a long time, because they may leave marks on

the case.

• This unit’s top and rear panels may get warm

after prolonged use. This is normal.

• If you do not use this unit for a long time, it may

not work properly the next time you turn it on, so

be sure to use it occasionally.

• When you’ve finished using this unit, remove all

discs and turn off the power.

9. Installing this Unit

• Install this unit in a well-ventilated location.

• Ensure that there’s adequate ventilation all

around this unit, especially if it’s installed in an

audio rack. If the ventilation is inadequate, the

unit may overheat, leading to malfunction.

• Do not expose this unit to direct sunlight or heat

sources, because its internal temperature may

rise, shortening the life of the optical pickup.

• Avoid damp and dusty places, and places subject

to vibrations from loudspeakers. Never put the

unit on top of, or directly above a loudspeaker.

• Install this unit horizontally. Never use it on its

side or on a sloping surface, because it may cause

a malfunction.

• If you install this unit near a TV, radio, or VCR,

the picture and sound quality may be affected. If

this occurs, move this unit away from the TV,

radio, or VCR.

10. Moisture Condensation

Moisture condensation may damage this unit.

Read the following carefully:

Moisture may condense on the lens of the optical

pickup, one of the most important parts inside this

unit.

• Moisture condensation can occur in the following

situations:

– The unit is moved from a cold place to a warm

place.

– A heater is turned on, or cold air from an air

conditioner is hitting the unit.

– In the summer, when this unit is moved from an

air conditioned room to a hot and humid place.

– The unit is used in a humid place.

• Do not use this unit when there’s the possibility of

moisture condensation occurring. Doing so may

damage your discs and certain parts inside this unit.

If condensation does occur, unplug the power cord

and leave the unit for two to three hours in the room

temperature.

This unit contains a semiconductor laser system and is

classified as a “CLASS 1 LASER PRODUCT”. So, to

use this model properly, read this Instruction Manual

carefully. In case of any trouble, please contact the store

where you purchased the unit.

To prevent being exposed to the laser beam, do not try

to open the enclosure.

CAUTION:

CLASS 1M VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT VIEW

DIRECTLY WITH OPTICAL INSTRUMENTS.

THIS PRODUCT UTILIZES A LASER. USE OF

CONTROLS OR ADJUSTMENTS OR PERFOR-

MANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARD-

OUS RADIATION EXPOSURE.

En-4

Precautions—Continued

The label on the right is

applied on the rear panel.

1. This unit is a CLASS 1

LASER PRODUCT and

employs a laser inside the cabinet.

2. To prevent the laser from being exposed, do not remove the

cover. Refer servicing to qualified personnel.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence in a residential installation.

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful inter-

ference to radio or television reception, which can be

determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV techni-

cian for help.

For Canadian Models

NOTE: THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION: TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

Modèle pour les Canadien

REMARQUE: CET APPAREIL NUMÉRIQUE DE

LA CLASSE B EST CONFORME À LA NORME

NMB-003 DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION: POUR ÉVITER LES CHOCS ÉLEC-

TRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

For British models

Replacement and mounting of an AC plug on the power

supply cord of this unit should be performed only by

qualified service personnel.

IMPORTANT

The wires in the mains lead are coloured in accordance

with the following code:

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured mark-

ings identifying the terminals in your plug, proceed as

follows:

The wire which is coloured blue must be connected to

the terminal which is marked with the letter N or

coloured black.

The wire which is coloured brown must be connected to

the terminal which is marked with the letter L or

coloured red.

IMPORTANT

The plug is fitted with an appropriate fuse. If the fuse

needs to be replaced, the replacement fuse must

approved by ASTA or BSI to BS1362 and have the

same ampere rating as that indicated on the plug. Check

for the ASTA mark or the BSI mark on the body of the

fuse.

If the power cord’s plug is not suitable for your socket

outlets, cut it off and fit a suitable plug. Fit a suitable

fuse in the plug.

For European Models

Declaration of Conformity

We,

ONKYO EUROPE

ELECTRONICS GmbH

LIEGNITZERSTRASSE 6,

82194 GROEBENZELL,

GERMANY

GROEBENZELL, GERMANY

ONKYO EUROPE ELECTRONICS GmbH

K. MIYAGI

declare in own responsibility, that the ONKYO product

described in this instruction manual is in compliance with the

corresponding technical standards such as EN60065,

EN55013, EN55020 and EN61000-3-2, -3-3.

En-5

Supplied Accessories

Make sure you have the following accessories

• To use , the CD Player must be connected with a

cable.

* In catalogs and on packaging, the letter at the end of the prod-

uct name indicates the color. Specifications and operations

are the same regardless of color.

Features

•VLSC

(Vector Linear Shaping Circuitry)

• Massive Power Transformer

• Wolfson 192 kHz/24-Bit D/A Converter

• Audiophile-Grade Capacitors

• Optical and Coaxial Digital Output

• Plays Audio CDs, MP3/WMA CDs, CD-R/RWs

• Quick Navigation for MP3/WMA CD Playback

• 2 Repeat Modes (Track/Full)

• 25 Track Programming

• Hi-Rigidity, Anti-Resonant Chassis

• Aluminium Front Panel

• RI-Compatible Remote Control

• 3-Mode Dimmer

*1 VLSC and the VLSC logo are registered trademarks of Onkyo

Corporation.

Remote controller RC-822C and two batteries

(R03/AAA)

Batteries are not supplied with products for China.

Audio cable (80 cm)

 cable (80 cm)

DIMMER

DISPLAY

MEMORY

SETUP

CLEAR

RANDOM

REPEAT

ENTER

En-6

Contents

Important Safety Instructions ........................... 2

Precautions......................................................... 3

Supplied Accessories........................................ 5

Features .............................................................. 5

Getting to Know the CD Player ......................... 7

Front Panel.................................................................7

Display.......................................................................8

Rear Panel..................................................................8

Remote Controller .....................................................9

Installing the Batteries.............................................10

Aiming the Remote Controller ................................10

Disc Notes......................................................... 11

Connecting the CD Player ............................... 13

Audio Connections ..................................................13

Connections......................................................14

Connecting the Power Cord............................ 15

Basic Operation................................................ 15

Turning On CD Player.............................................15

Setting Auto Standby (ASb)....................................15

Changing the Display Brightness ............................15

Using Headphones...................................................15

Disc Playback ................................................... 16

Using the Remote Controller...................................17

Displaying CD Information.....................................17

Selecting Files (MP3/WMA CDs)...........................18

Selecting Files in Navigation Mode ........................18

Selecting Files in All Folder Mode..........................19

Selecting a Folder during Playback (Search Mode) 19

Displaying MP3/WMA Information .......................20

Various Playback Modes ................................. 21

Random Playback....................................................21

Memory Playback (For Audio CDs) .......................21

Memory Playback (For MP3/WMA CDs) ..............22

Repeat Playback ......................................................23

Setting for MP3/WMA....................................... 24

Setting MP3/WMA Preferences ..............................24

Troubleshooting............................................... 26

Specifications................................................... 27

En-7

Getting to Know the CD Player

a  ON/STANDBY button (15)

Press to turn on or standby the C-7030.

b Disc tray (16)

The CD is loaded here.

c Open/Close [] button (16)

Press to open and close the disc tray.

d Pause [] button (16, 17)

Press to pause playback.

e Stop [] button (16 – 19, 24)

Press to stop playback.

f Play [] button (16 – 19, 21, 22)

Press to start playback.

g PHONES jack (15)

This is a standard stereo jack for connecting stereo

headphones.

h PHONES LEVEL knob (15)

Use to control the phones level.

Turn the knob clockwise to increase the phones

level and counterclockwise to decrease it.

i DISPLAY button (17, 20, 21)

Press to change the displayed information.

j Remote control sensor (10)

Receives control signals from the remote controller.

k Display (8)

See next page.

l []/[] buttons (16, 17, 19, 21)

Press to select the previous or next track.

Hold down the buttons to fast-reverse or fast-

forward during playback.

m REPEAT button (23)

Press to set the repeat playback or 1-repeat playback

mode.

Front Panel

En-8

Getting to Know the CD Player—Continued

a  /  indicators

The  indicator lights up for playback.

The  indicator lights up while playback is paused.

b MP3, WMA indicators

Lights up when an MP3 or WMA CD is loaded.

c FOLDER indicator

Lights up when folder playback is selected.

d FILE indicator

Lights up when an MP3 or WMA file number is

being displayed.

e TRACK indicator

Lights up when a CD track number is being

displayed.

f Playback mode indicators

MEMORY lights up when memory playback is

selected.

RANDOM lights up when random playback is

selected.

REPEAT lights up when repeat playback is

selected for all tracks.

REPEAT 1 lights up when repeat playback is

selected for one track.

g Message area

Various information is displayed here.

h TITLE, ARTIST, and ALBUM indicators

TITLE lights up when the title (ID3 tag) of an

MP3/WMA track is being displayed.

ARTIST lights up when the artist name from an

MP3/WMA track (ID3 tag) is being displayed.

ALBUM lights up when the album name from an

MP3/WMA track (ID3 tag) is being displayed.

i DISC, TOTAL indicators

These indicators light up when the total disc time or

track time is being displayed.

j REMAIN indicator

This indicator lights up when the remaining disc

time or track time is being displayed.

a ANALOG AUDIO OUTPUT jacks (13, 14)

These analog audio outputs can be connected to an

amplifier’s analog inputs by using the supplied

audio cable.

b REMOTE CONTROL jacks (14)

These two identical (Remote Interactive) jacks

can be connected to the  jacks on your other

Onkyo components for interactive control. To use

, the C-7030 must be connected with an 

cable and an audio cable.

c DIGITAL AUDIO OUTPUT OPTICAL/

COAXIAL jacks

These two digital audio outputs can be connected to

a digital audio input on an amplifier or recorder.

Display

Rear Panel

1 2 3

En-9

Getting to Know the CD Player—Continued

The page numbers in parentheses show where you can find the main explanation for each item.

a [] button (15)

Press to turn on or standby the C-7030.

b DIMMER button (15)

Press to adjust the display brightness.

c Pause [] button (16, 17)

Press to pause playback.

d RANDOM button (21)

Select the Random playback mode.

e Play [] button (16 – 19, 21, 22)

Press to start playback.

f []/[] buttons (16, 17, 19, 21)

Press to select the previous or next track.

g Stop [] button (16, 18, 19, 24)

Press to stop playback.

h ///buttons (15, 18, 19, 21, 22, 24)

Press the Arrow buttons to configure various

settings, and then press the ENTER button to set

them.

These buttons can be also used to select a track.

i ENTER button (15, 19, 21 – 24)

Press to set a selected preference.

j SEARCH button (19)

For MP3, WMA CDs, this button is used to search

and select a file number or a folder number.

k SETUP button (24)

Press to access various settings.

l Number buttons (17, 19)

Use to enter track numbers.

m Open/Close [] button (16)

Press to open and close the disc tray.

n DISPLAY button (17, 20)

Press to change the displayed information.

o REPEAT button (23)

Select the repeat playback or 1-repeat playback

mode.

p []/[] buttons (17, 21)

Hold down to fast-reverse or fast-forward during

playback.

q MEMORY button (21, 22)

Select the Memory playback mode.

r CLEAR button (21)

Use to clear any numbers that have been entered

during numeric input. When making a memory

setting, the selected track is erased.

Remote Controller

822C

DIMMER DISPLAY

SEARCH MEMORY

SETUP

CLEAR

123

456

7 8 9

RANDOM REPEAT

ENTER

En-10

Getting to Know the CD Player—Continued

To open the battery compartment, press the

small hollow and slide open the cover.

Insert two batteries (R03/AAA) into the

compartment.

Carefully follow the polarity diagram (positive (+)

and negative (–) symbols) inside the battery

compartment.

Batteries are not supplied with products for China.

Replace the cover and slide it shut.

Notes:

• If the remote controller doesn’t work reliably, try

replacing the batteries.

• Don’t mix new and old batteries or different types of

batteries.

• If you intend not to use the remote controller for a long

time, remove the batteries to prevent damage from

leakage or corrosion.

• Expired batteries should be removed as soon as possi-

ble to prevent damage from leakage or corrosion.

When you operate the remote controller, point it at the

CD Player’s remote control sensor, as shown below.

Notes:

• The remote controller may not work reliably if the CD

Player is subjected to bright light, such as direct sun-

light or inverter-type fluorescent lights. Keep this in

mind when installing.

• If another remote controller of the same type is used in

the same room, or the CD Player is installed close to

equipment that uses infrared rays, the remote control-

ler may not work reliably.

• Don’t put anything, such as a book, on the remote con-

troller because the buttons may be pressed inadver-

tently, thereby draining the batteries.

• The remote controller may not work reliably if the CD

Player is installed in a rack behind colored glass doors.

Keep this in mind when installing.

• The remote controller will not work if there’s an

obstacle between it and CD Player’s remote control

sensor.

Installing the Batteries Aiming the Remote Controller

822C

IMMER

ISP

SEA

SETUP

123

NDOM

PEA

ENTER

(

)

Remote control sensor

En-11

Disc Notes

Precautions for Playback

Compact discs (CDs) with the following logo on the

label surface can be used.

Do not use discs designed for purposes other than audio,

such as CD-ROMs for PC use. Abnormal noise could

damage the speakers or amplifier.

* This CD player supports CD-R and CD-RW discs.

Note that some discs may not play back because of the disc

characteristics, scratches, contamination or the recording state.

A disc recorded with an audio CD recorder will not play back

unless it is finalized.

Never use discs which have an unusual shape (such as

hearts or octagons). These types of discs could jam and

damage the CD player.

CD Playback with Copy-control Function

Some audio CDs with copy-control functionality do not

comply with official CD standards. These are special

discs and cannot be played with this CD player.

Playback of MP3 and WMA Discs

MP3 and WMA files recorded on a CD-R/CD-RW can

be played with this CD player.

• Use discs which have been recorded following the

ISO9660 Level 2 file system. (The supported directory

depth is eight levels, the same as ISO9660 Level 1)

• Discs recorded with the hierarchical file system (HFS)

cannot be played.

• Up to 99 folders (including the root folder), and up to

499 files (including root) and files can be recognized

and played.

Notes:

• A disc recorded with a recorder or personal computer

may not play in some cases. (Cause: Disc’s character-

istics, damaged or dirty disc, dirt on player’s lens, dew

condensation, etc.)

• A disc recorded on a personal computer may not play

because of the application settings or environment.

Record the disc with the proper format. (Contact the

application maker for details.)

• A disc with insufficient storage capacity may not play

back properly.

Playback of MP3 Discs

• Only MP3 files with the extension “.MP3” or “. mp3”

are supported.

• This CD player supports files recorded in MPEG 1

Audio Layer 3 (32-320kbps), with a sampling fre-

quency of 32/44.1/48 kHz.

• Variable bitrates (VBR) between 32kbps and 320kbps

are supported. The time information during VBR

playback may not display correctly.

Playback of WMA Discs

• WMA stands for “Windows Media

Audio”, an audio

compression technology developed by Microsoft Cor-

poration USA.

• Only WMA files with the extension “.WMA” or

“.wma” are supported.

• Encode the WMA file with an application approved　

by Microsoft Corporation USA. The file may not　

play back correctly if encoded with an unapproved　

application.

• Variable bitrates (VBR) between 32kbps and　

192kbps (32/44.1/48 kHz) are supported.

• Copyright-protected WMA files cannot be played　

back.

• WMA Pro, Lossless and Voice are not supported.

* Windows Media is a registered trademark or trademark of

Microsoft Corporation in the United States and/or in other

countries.

Handling Discs

Hold discs by the edge, or by the center hole and edge.

Avoid touching the playback surface (surface with noth-

ing printed on it).

Do not attach paper or stickers, or write on the playback

or label surface of the disc. Take care not to scratch or

damage the disc.

Label surface

(printed surface)

Playback surface

En-12

Disc Notes—Continued

Precautions for Rental Discs

Do not use discs with residue from cellophane tape,

rental discs with labels which are peeling off, or discs

with decorative labels. This type of disc could get stuck

in the CD player, or could damage the CD player.

Precautions for Inkjet Printable Discs

Do not leave a CD-R/CR-RW having a label printed with

an inkjet printer in the CD player for a long time. The

disc could get stuck in the CD player, or could damage

the CD player.

Remove the disc from the CD player when not being

played, and store it in a case. A freshly printed disc will

stick easily, and should not be played immediately.

Caring for Discs

If the disc is dirty, the C-7030 will have a hard time read-

ing signals, and the audio quality may drop. If the disc is

dirty, gently wipe off fingerprints and dust with a soft

cloth. Lightly wipe from the center outwards.

To remove stubborn dust or dirt,

wipe the disc with a soft cloth

dampened with water, and then

dry it with a dry cloth. Do not

use cleaning spray for analog

records or antistatic agents, etc.

Never use volatile chemicals

such as benzine or paint thinner

as they can impregnate the disc

surface.

En-13

Connecting the CD Player

• Before making any connections, read the manuals

supplied with your other components.

• Don’t connect the power cord until you’ve completed

and double-checked all connections.

Connection Color Coding

RCA-type audio connections are usually color-coded:

red and white. Use red plugs to connect right-channel

audio inputs and outputs (typically labeled “R”). Use

white plugs to connect left-channel audio inputs and out-

puts (typically labeled “L”).

• Push plugs in all the way to

make good connections (loose

connections can cause noise or

malfunctions).

• To prevent interference, keep

audio cables away from power cords and speaker

cables.

Optical/Coaxial Digital Jack

The unit supports 16 bit, 44.1 kHz PCM signal digital

output.

The C-7030’s optical digital jack has a shutter-type cover

that opens when an optical plug is inserted and closes

when it’s removed. Push the plug in all the way.

Caution: To avoid damaging the shutter, hold the optical

plug straight when inserting and removing.

Note:

Do not put anything on top of the C-7030, as it may inter-

fere with proper ventilation.

Audio Connections

Analog audio

cable

Left (white)

Right (red)

Left (white)

Right (red)

Right!

Wrong!

RCA/phono

audio cable

(supplied)

Optical digital

cable (not

supplied)

Hi-fi amp, AV receiver

Connect one or

the other

Coaxial cable

(not supplied)

Connect one or

the other

Coaxial cable

(not supplied)

Optical digital

cable (not sup-

plied)

CD-R, MiniDisc, DAT recorder

Disconnect the power

cord before making

any connections!

Optical IN

Coaxial IN

Optical IN

Coaxial IN

En-14

Connecting the CD Player—Continued

With  (Remote Interactive) you can control the

C-7030 together with your other -compatible Onkyo

AV components. With some Onkyo AV receivers you

can use one remote controller to control all your Onkyo

components and use the following special  functions:

Direct Change

If your C-7030 is connected to an -compatible Onkyo

hi-fi amp or AV receiver, when you start playback on the

C-7030, the AV receiver will select the C-7030 as the

input source.

Remote Control Operation

You can control the C-7030 by using your Onkyo ampli-

fier’s remote controller. See the amplifier’s instruction

manual for details.

To use the  functions, you need to connect one of the

C-7030’s connectors to an connector on another

AV component in your system by using the supplied 

cable.

See the manuals supplied with your other -compati-

ble AV components for more information.

Notes:

• Use only cables for connections.

• The C-7030 has two connectors. You can connect

either one to your Onkyo hi-fi amp or AV receiver. The

other connector is for connecting additional -com-

patible components.

• Connect the C-7030’s connector only to Onkyo

AV components. Connecting to other manufacturer’s

AV components may cause them to malfunction.

• Some Onkyo -compatible AV components may not

support the special functions described here.

Connections

RCA/phono audio cable (supplied)

 cable (supplied)

Coaxial cable (not supplied)

Onkyo Hi-fi amp, AV receiver

Disconnect the power

cord before making any

connections!

Coaxial IN



To use  you must make an analog audio connection

(RCA/phono) between the C-7030 and your other Onkyo

component even if they are connected digitally.



En-15

Connecting the Power Cord



Before connecting the power cord, connect all of the other components.

Basic Operation

To turn on the CD Player, press the [ ON/STANDBY]

button on the unit or the remote controller. Press the

[ ON/STANDBY] button again to set the CD Player to

Standby.

You can specify that if the CD Player is left stopped for

30 minutes, the power will automatically turn off, plac-

ing the unit in Standby mode (Auto Standby function).

On the North American model:

The default setting is “Off”.

On the European model:

The default setting is “On”.

Make settings for this function while playback is

stopped.

Press the [SETUP] button.

Use the [] or [] button to display “ASb”;

then press the [ ENTER ] button.

Use the [] or [] button to switch “Off” or

“On”; then press the [ ENTER ] button.

“COMPLETE” appears on the display.

Note:

If playback is paused, the power will remain on even

after 30 minutes have elapsed; the Auto Standby func-

tion will not operate.

Press the remote controller’s [DIMMER]

button repeatedly to select the following

options:

Turn down the volume, then connect your stereo head-

phones to the [PHONES] jack.

You can adjust the volume by using the [PHONES

LEVEL] knob.

Plug the power cord into a

suitable electrical outlet

Turning On CD Player

Setting Auto Standby (ASb)

ON/STANDBY

DIMMER DISPLAY

ENTER





Changing the Display Brightness

Using Headphones

DIMMER

Normal Dim Dimmer

PHONES

jack

En-16

Disc Playback

Press the Open/Close [] button to open

the disc tray.

Place the CD on the tray with the label-side

facing up.

If you're playing an 8 cm CD, place it in the center

of the tray.

To start playback, press the Play []

button.

The disc tray closes and playback starts.

The contents of the disc are displayed when you use the

Open/Close [] button to load a disc and when you press

the Stop [] button during playback.

Example displays:

Selecting Tracks

To return to the beginning of the track that’s currently

playing or paused, press the Previous [] button.

Press the Previous [] button repeatedly to select ear-

lier tracks.

Press the Next [] button repeatedly to select subse-

quent tracks.

• To Fast-Forward or Fast-Reverse

During playback or while playback is paused, hold

down the [] button on the CD Player to fast-

forward or the [] button on the CD Player to fast-

reverse.

If you use the remote controller, use the []/[]

buttons.

On MP3/WMA CDs, fast-reverse only works within

the MP3/WMA file that’s currently playing.

• To Pause Playback

Press the Pause [] button. The Pause [] indicator

appears.

To resume playback, press the Play [] or Pause []

button again.

• To Stop Playback

Press the Stop [] button.

• To Eject the CD

Press the Open/Close [] button to open the disc tray.

Notes:

- MP3/WMA CDs -

If you press the [] button during playback or while

playback is paused, the beginning of the current file is

selected.

If you select a file while playback is stopped, press the

Play [] button to start playback.

You can select MP3/WMA files in other folders by using

the []/[] buttons.

[

DIMMER DISPLAY

RANDOM REPEAT

ENTER









 / 

Disc tray

“DISC TOTAL” lights up.

• Audio CD

Total n u mber

of folders

Total number

of files

• MP3/WMA Discs

Disc name or Format

Total number

of tracks

Total playing time

En-17

Disc Playback—Continued

Press the CD Player’s or the remote controller’s [DISPLAY] button (repeatedly) to show the following CD information.

While Playback is Stopped

During Playback or While Playback is

Paused

See page 20 for details on displaying MP3/WMA

information.

Using the Remote Controller

822C

DIMMER DISPLAY

SEARCH MEMORY

SETUP

CLEAR

123

456

7 8 9

RANDOM REPEAT

[]/[]

Press to fast-forward or fast-

reverse

During playback or while playback is

paused, press and hold the Fast

Forward [] button to fast-forward, or

the Fast Reverse [] button to fast-

reverse.

[DISPLAY]

Press repeatedly to display

CD information

See below for details.

Use the number buttons as

shown in the examples below to

select tracks.

To select: Press:

Tra c k #8

Tra c k #10

Tra c k #34

Used to enter numbers over 9.

With MP3/WMA CDs, you can select

files in the current folder using these

buttons.

[]

Press to pause playback

[]/[]

Press to select tracks

• Press the Previous [] button to

locate the beginning of the currently play-

ing or paused track. Press it repeatedly

to select earlier tracks.

• Press the Next [] button repeatedly

to select subsequent tracks.

For MP3/WMA files, you can select files in

other folders.

[]

Press to stop playback

[]

Press to start playback

Displaying CD Information

DISPLAY

On the unit Remote controller

Total playing time

Total number of tracks

The elapsed time is normally

displayed.

indicator.

Lights up while the remaining

track time is being displayed.

“REMAIN”

Lights up while the remaining disc time is

being displayed.

If the total time is more than 99 minutes

and 59 seconds, “– –:– –” is displayed.

“TOTAL

REMAIN”

En-18

Disc Playback—Continued

For MP3/WMA CDs, files (MP3/WMA files) may be

organized in a hierarchy, with folders containing files

and subfolders, as shown below.

• In this manual, MP3/WMA files are referred to as

files. Likewise, folders (directories) are referred to

as folders.

If you don’t select a specific MP3/WMA file or folder

for playback, all of the MP3/WMA files on the CD will

be played in numerical order starting with file #1.

On this CD Player, there are two modes for selecting

files (MP3/WMA files): Navigation mode and All

Folder mode.

In Navigation mode, you can select files (MP3/WMA

files) by navigating through the folder hierarchy, moving

in and out of folders and subfolders.

In All Folder mode, all folders appear at the same level,

making it easy to select folders regardless of the

hierarchy.

While playback is stopped, press the remote

controller’s [] or [] button to enter Navigation

mode, the [] or [] button to enter All Folder mode.

If you use the CD Player’s button, press the []

button to enter Navigation mode, press and hold the

[] button to enter All Folder mode.

You can change the way in which these buttons change

the playback mode. This lets you disable the file

selection methods described in Navigation mode or All

Folder mode. (See “STOP KEY” in “Setting MP3/WMA

Preferences” on page 25.)

In Navigation mode, you can select files by navigating

through the folder hierarchy. This mode can only be used

while playback is stopped.

While playback is stopped, press the [] or

[] button.

The compact disc player enters Navigation mode

and “[ROOT]” appears on the display.

Press the [] or [ENTER] button (front

panel: []).

The first folder name in ROOT appears on the

display.

If the disc contains no folders, the first file name

appears.

Use the []/[] or []/[] buttons to

select other folders and files at the same

level.

To move up a level, press the [] or [] button

(front panel: []).

Folders that don’t contain files or subfolders can’t

be selected.

Press the [ENTER] or [] button to move

down a level (front panel: []).

Use the []/[] or []/[] buttons to

select a file in the folder.

Selecting Files (MP3/WMA CDs)

File #11

File #1

File #10

Folder #3

File #12

Root Folder #1

Folder #2

File #13

Folder #4

File #14

File #18

Selecting Files in Navigation Mode

DIMMER DISPLAY

RANDOM REPEAT

ENTER



 / 

ENTER







En-19

Disc Playback—Continued

Press the [ENTER] or [] button.

Playback will start with the specified file or folder

and continue until all of the files on the disc have

been played.

To cancel the procedure at any point, press the [] on the

remote controller.

Note:

• The behavior of the [] on the CD Player can be set

from “STOP KEY” preference (page 25).

In All Folder mode, you don’t have to navigate the folder

hierarchy because all folders that contain files appear at

the same level. This mode can only be used while

playback is stopped.

While playback is stopped, press the [] or

[] button (front panel: press and hold the

[]).

The CD Player enters All Folder mode, and “1-”

appears on the display.

Use the []/[] or []/[] buttons to

select the other folders.

You can select any folder that contains files.

Press the [] button (front panel: []).

The first file name inside the folder appears.

Use the []/[] or []/[] buttons to select

the files within the folder.

To select another folder, press the [] button again

(front panel: []), and then use the [/]

buttons to select it.

Press the [ENTER] or [] button to start

playback.

Playback will start with the specified file or folder

and continue until all of the file on the disc have

been played.

To cancel the procedure at any point, press the [].

■ To Select Folders and Files by Number

1. Use the number buttons as shown in the examples

below to enter folder/file numbers.

To select: Press:

Folder/File #8

Folder/File #10

Folder/File #34

Used to enter numbers over 9.

2. Playback starts. When you enter folder number,

playback will start from the first file in the selected

folder. If a folder contains more than 99 files, single

and double-digit file numbers must be preceded by

zeros. For example, to specify file #8, press >10, 0,

0, and 8. To specify file #34, press >10, 0, 3, and 4.

To specify file #134, press >10, 1, 3, and 4.

Note:

• The behavior of [] on the CD Player can be set from

“STOP KEY” preference (page 25).

Press the [SEARCH] button.

The display blinks.

Selecting Files in All Folder Mode

DIMMER DISPLAY

RANDOM REPEAT

ENTER















Selecting a Folder during Playback

(Search Mode)

SEARCH MEMORY

SETUP

123

RANDOM REPEAT

ENTER





En-20

Disc Playback—Continued

To select the previous folder, press the

Previous [] button.

To select the next folder, press the Next []

button.

Press the [ENTER] button to display the file

name, and start playback the selected file.

Use the Previous [] and Next []

buttons to select the previous or next file,

and start playback.

Note:

The [SEARCH] button cannot be used during “Random

Playback” or “Memory Playback”.

You can display various information about the MP3/

WMA file currently playing, including ID3 tags such as

title name, artist name, and album name.

During playback, press the [DISPLAY] button

repeatedly to display the following MP3/WMA

information.

Elapsed file time: The length of time that the current file

has been playing (default display). If the elapsed time is

more than 99 minutes and 59 seconds, “– –:– –” is dis-

played.

File name: Name of the current file.

Folder name: Name of the current folder.

Title: Title of the current file (if ID3 tag is present).

When there is no ID3 tag, “TITLE-NO DATA” appears.

Artist name: Name of the artist (if ID3 tag is present).

When there is no ID3 tag, “TITLE-NO DATA” appears.

Album name: Name of the album (if ID3 tag is present).

When there is no ID3 tag, “TITLE-NO DATA” appears.

Sampling rate and bit rate: Sampling rate and bit rate

of the current file.

Notes:

• To display the disc name, press the [DISPLAY] button

while playback is stopped.

• If a file or folder name contains any characters that

cannot be displayed, an underscore will appear in

place of those characters. Alternatively, you can set

the CD Player so that names containing such

characters are displayed as “FILE n” or “FOLDER n,”

“n” being the file or folder number (see “BAD

NAME” on page 24).

Displaying MP3/WMA Information

DIMMER DISPLAY

DISPLAY

Page is loading ...

ONKYO C-7030 User manual

Brand: ONKYO

Model: C-7030

Category: CD players

Type: User manual

This manual is also suitable for

C-7030C-7070C7030 NOIR

Download PDF

report

ONKYO C-7030 User manual

This manual is also suitable for

ONKYO C-7030 User manual

Related papers

Other documents