Ampac FireFinder LED Mimic Installation guide

Brand: Ampac

Model: FireFinder LED Mimic

Type: Installation guide

ADVANCED WARNING

SYSTEMS

FireFinder LED Mimic 302-7150

Installation Guide

Item Numbers: 201-0544

MAN2499-2

N1236

Page 1

WORLD LEADER OF INNOVATIVE SOLUTIONS IN FIRE DETECTION AND ALARM SYSTEMS

Ampac Technologies Australia Tel: +61 8 9201 6100 Europe Tel: +44 (0) 1302 833 522 New Zealand Tel: +64 9 443 8072 www.ampac.net

Description:

The LED Mimic (302-715), LED Mimic Display Board

(302-733), and the FireFinder Controller Interface Card

[CIC] (302-725) is designed to provide remote indication

of the current status of an NZ FireFinder FACP. The

mimic will indicate any zones, or sensors in alarm as

well as providing common Fire, Defect, DBA, system

Normal indication, and a General Purpose Relay

Output.

LED Mimic 302-715 Specifications

Function Keys Lamp Test

Lamp Reset

Buzzer Mute

CPU Reset

Address Switches

System Switches

Indicator

(LED’s)

Power On

Normal

Fault

Power Supply

TB1: 20 to 28VDC @ 100 mA

CN6: 5 volt output (aux power)

Outputs

CN1, 2, 3 & 4: 32 outputs for Zone

indication

CN5: 5 outputs for Fire, Pre-Alarm,

DBA, Defect and Normal indication

CN5: 1 buzzer output

TB4: General Purpose Output, 1A

Voltage-free changeover contacts

Inputs

CN5: 5 inputs for Mimic Reset, Lamp

Test, Buzzer Mute, Bell Isolate and

Evacuate

The LED Mimic derives power (Max 2 Amps) and

RS485 comms from the FireFinder CIC (302-725). In

small systems with 1, or 2 LED Mimics on cable runs of

less than 400 meters suggested cabling is 2 Pair

Twisted 100Ω Shielded Data Cable (0.2mm² cores

minimum) e.g. OLEX JECP87F5002, BELDEN 9804. In

larger systems with more than two LED Mimics or long

cable distances use 1 Pair Twisted 100Ω Shielded Data

Cable e.g. OLEX JECP87F5001, BELDEN 9841 for

communications. It will be necessary to supply power to

LED Mimics via separate cables. The size of the power

cables will depend on the number of mimics used and

the total distance Table 2.

Operation of the LED Mimics is not monitored by the

FACP. If communications to the LED Mimics fail, the

LED Mimic will flash the 'Defect' LED rapidly to indicate

a communication defect. Correct operation of the LED

Mimic and FACP is confirmed by the 'Normal' LED

flashing on the LED Mimic.

Recommended Maximum Cabling Distances using 2

Pair Data Cable.

Number of LED Repeater Boards Max Distance

1 400m

2 200m

Table 1

Recommended Power Cable Sizes for Larger

Systems

Number

of LED

Mimics

Distance

= <500m

Distance

= 500m<

>1Km

Distance

= 1Km<

>1.5Km

Distance

=1.5Km<

>2Km

1 0.3mm² 0.5mm² 1mm² 1.5mm²

2 0.5mm² 1mm² 1.5mm² 2.5mm²

3 0.75mm² 1.5mm² 2.5mm² 4mm²

Table 2

Installation:

Controller Interface Card 302-7250 & LED Repeater

Board 302-7150.

Observe anti-static precautions at all times

1. Power system down, and remove batteries.

2. Mount the Controller Interface Card on standoffs in

the left side of the panel.

3. To connect the CIC to the FireFinder Main Board

302-674, plug one end of the sixteen-way cable

provided into CN1 of the CIC and the other end into

CN18 of the Main Board 302-674. Connect TB1

and TB3 of the CIC to the external cabling.

4. Mount the LED Mimic Board 302-715 and the

Expansion LED Board 302-733 on stand-offs within

an enclosure. Connect TB1 of the 302-715 LED

Mimic to the external cabling then connect as

shown in Table 3.

LED Mimic Board Expansion Board

CN5 CN1

CN1 CN2

CN3 CN3

Table 3

5. Set Switches as follows SW2-1 ON, SW2-2 OFF,

SW2-3 OFF, SW2-4 OFF, SW2-5 OFF, SW2-6

OFF , SW2-7 OFF, and SW2-8 OFF (All LED

Mimic Boards are set to address No. 4).

6. Power up and test LED Mimic functions.

ADVANCED WARNING

SYSTEMS

FireFinder LED Mimic 302-7150

Installation Guide

Item Numbers: 201-0544

MAN2499-2

N1236

Page 2

WORLD LEADER OF INNOVATIVE SOLUTIONS IN FIRE DETECTION AND ALARM SYSTEMS

Ampac Technologies Australia Tel: +61 8 9201 6100 Europe Tel: +44 (0) 1302 833 522 New Zealand Tel: +64 9 443 8072 www.ampac.net

Communications

& 27VDC From:

FACP CIC

EXT Cabling

Communications

& Power To Next:

LED Mimic

Board 302-715

To LED D is p l ay

302-733 CN1

Fire, Pre-alarm,

DBA,Defect, Normal

To LED Display

302-733 CN2

Zones 1-8

To LED Display

302-733 CN3

Zones 9-16

To LED Display

302-733/1 CN2

Zones 17-24

To LED Display

302-733/1 CN3

Zones 25-32

N/F

SCR TX- TX+

+27

CN5

CN1

CN2

CN3

CN6

CN4

TB3

TB1

TB5

TB4

SW6

SW4

SW5

SW2

SW7

SW3

POWER OUT

Buzzer Mute

Lamp Reset

Lamp Test

FAULT

NORMALPOWER ON

LED DISPLAY

N/ON/CC0VGPI

OUT

OV GND

CPU

RESET

OFF

ADDRESS

SYSTEM

LEDS FLASH

SCR TX- TX+

FIT K2

FOR BUZZER

ALM

PRE

DBA

FLT

NOM

RST

EVC

LED

LED AUX 5V

SW2 Settings

1-5, Address ( Max 31 )

6, Configuration

set to OFF for FireFinder

set to ON for NZ3200

7, Not used

8, LED Setting

ON = Flash OFF = Steady

1A Voltage

Free Contact

Programmable

I/P

1 2 3 4 5 6 7 8

SCR TX- TX+

+27

TB3

TB1

OUT

OV GND

SCR TX- TX+

To TB1 on

next LED

Mimic Board

LED MIMIC DRIVER BOARD 302-715

TB1

MIMICS

Tx +

Tx -

302-725CIC

NOTE:INSERT 'LK1'

ON LAST LED MIMIC

DRIVER BOARD

CN1

CN18

FIREFINDER MAIN BOARD

302-674

CN4

CN3

CN2

CN3

CN1

CN2

CN5

CN1

LED MIMIC DISPLAY BOARDS 302-733

ZONES 1 - 16ZONES 17 - 32

FIRE

PRE-ALARM

DBA

DEFECT

NORMAL

RESET

BUZZER

FACP

SCR

+27

Tx +

Tx -

GND

SCR

+27

TB3

COMMS & PWR

Figure 1: General Power Wiring and Board Layout

2 1

OUT

302-725

TB3

CN1

U10

U13

U11

U12

TB2

TB1

CN5

CN6

CN3

CN2

TO PREVIOUS CIC CN3 (OUT)

TO CN2 ( IN ) OF NEXT CIC OR CN1 OF THE NIC

27VDC IN

AUX FUSED

( F1 2A )

27VDC OUT

+ -

- - -

K1, K2:

LINK PINS 1 & 2

ON FIRST CIC ONLY

COM

TXD

RXD

RTS

CTS

SCRN

TRX-

TRX+

+27V

1 2 3 4 5 6 7 8

302-715 REMOTE LED INDICATOR BOARD

REMOTE BUZZER

EVACUATION SW

BELL ISOLATE SW

BUZZER MUTE SW

LAMP TEST SW

RESET SW

302-733 REMOTE

EXPANSION

LED BOARD

26 WAY RIBBON

16 WAY RIBBON

RS485

1.2K Max

27VDC

MUTE

TEST

N/F

SCR TX- TX+

+27

CN5

CN1

CN2

CN3

HY1

CN6

CN4

TB3

TB1

TB5

TB4

RL1

U10

SW6

SW4

SW5

SW2

SW7

CN7

SW3

POWER OUT

BUZZER

RESET

LAMP

FAULTNORMALPOWER ON

LED DISPLAY

N/ON/CC0VGPI

302-715

OUT

OV GND

CPU RESET

OFF

ADDRESS

SYSTEM

LEDS FLASH

FACT ORY

USE ONLY

SCR TX- TX+

FIT K1 ON

LAST MIMIC

ONLY

FIT K2

FOR BUZZER

ALM

PRE

DBA

FLT

NOM

RST

EVC

LED

LAMP

LED AUX 5V

BZ1

TB2

TB1

CN1

D10

D20

D19

D18

D17

D15

D14

D13

D12

D11

CN3

CN2

D21

RESET

LAMP TSTBZ MUTEBELL ISOLEVAC

BZ+BZ-

ALARM

PRE-ALM

DBA

DFCT

NORM

D16

IF APPLICABLE ONLY

LOWER SECTION OF

BOARD IS USED FOR

ZONES 17 - 32

IF APPLICABLE CN3, CN4 CONNECT TO CN2, CN3

RESPECTIVELY OF 2nd REMOTE EXPANSION LED

BOARD FOR ZONES 17- 32

+27V

TB1

SCRN

TRX-

TRX+

TB3

+ -

a b c

1 2 3 4 5 6 7 8

FIREFINDER

MAIN BOARD (302-674)

O O O

CN18

TO LOOP

COMMS

(CN18)

+27

TB1

GND

SCR TX- TX+

SLAVE CPU3SLAVE CPU4 SLAVE CPU2

NOTE; SLAVE CPU1 IS SITUATED ON THE MAIN BOARD

Figure 2: General Cabling

Main System Board

302 708

Controller Interface Card

302 725

Mimic

Driver

Board

302 715

Remote LED

Board 302 733

CN5

CN1

CN2

CN3

CN4

CN1

CN2

CN3

CN4

CN5

TB1

CN18

Comms

RS485

+/- 27VDC

CN1

CN6

27VDC IN

Figure 3: Block Diagram

Ampac FireFinder LED Mimic Installation guide

Ampac FireFinder LED Mimic Installation guide

Ampac FireFinder LED Mimic Installation guide

Related papers

Other documents