SoundCraft RK100M User manual

Operating Guide

Radio Key

®

RK-65K and RK-65KS

with RK100M instructions

Stand Alone • Proximity Access Control System

With Dynascan

®

Technology*

SOUNDCRAFT, INC.

V060107 6451

Radio Key

®

RK-65K/RK-65KS

Operating Guide

Table of Contents

Introduction .........................................................................1

Ordering Transponders ......................................................3

Programming Radio Key

®

RK-65K/RK-65KS ..................4

Programming Radio Key

®

RK100M .................................5

Handheld Programmer (RK-HHP) &

Programming Deck (RK-PD1) ......................................6

Programming Steps ..........................................................7

Programming Hints ..........................................................13

Basic Operation ...............................................................19

Converting to RK100M Mode ...........................................21

Warranty ...........................................................................28

Speciﬁ cations ...................................................................29

Certiﬁ cations .....................................................................31

Illustrations

Figure 1, Radio Key

®

RK-65K & RK-65KS Units ................2

Figure 2, Programming Deck & Hand-Held Programmer ...2

i

Radio Key

®

RK-65K Operating Guide

Secura Key  1

INTRODUCTION

The Radio Key

®

RK-65K is a programmable single-door access

control system which controls access for up to 65,000 users. It

can control an electric strike, magnetic lock, or gate operator,

and has an additional programmable input which may be set

as a remote open input or as an LED/Beeper control for use

with the Wiegand output. A Wiegand output is also provided to

allow for later upgrading to an on line system. Information on

using the RK-65K as a Wiegand reader is contained on page 18

The major components are shown in Figures 1 and 2.

The Radio Key

®

RK-65K Access Control Unit contains the CPU,

memory, access relay, and an internal reader. It has a beeper, and

a bi-color LED indicator. An RK-HHP Handheld Programmer or an

RK-PD1 Program Deck (not included), is used to add or delete tran-

sponders, to set the operating mode, to program the password and

latch timer. The Radio Key

®

RK-65K is compatible with the Secura

Key SecuRelay™, an intelligent relay module used to eliminate the

possibility of break-in by attacking the access control unit.

The current version of this product also replaces the RK100M.

The RK100M reads randomly encoded tags and supports only

100 users. To convert this unit to RK100M mode, follow the

instructions on Page 21.

Radio Key

®

RK-65K Operating Guide

Secura Key  2

Figure 1 - Radio Key

®

RK-65K & RK-65KS Units

NOTE: All references to RK-65K also apply to the RK-65KS.

Figure 2 - Programming Deck (RK-PD1)

& Hand-Held Programmer (RK-HHP)

NOTE: Programming sequences are the same

using RK-PD1 or RK-HHP

Radio Key

®

RK-65K Operating Guide

Secura Key  3

ORDERING TRANSPONDERS

The Radio Key

®

RK-65K works with Secura Key RKCM-02

molded (clamshell) cards, RKCI-02 ISO-standard cards and

RKKT-02 key ring tags. Card Format 303 and Format 201

can be used.

When you order Format 303 transponders for a new project you

will be assigned a new Facility Code and your transponders will

begin with ID number 1. As you need additional cards or tags

you can order the same Facility Code, specifying the starting

number, which will be one digit higher than your highest existing

transponder.

If you use Format 201, these are shipped from stock and you

may receive cards or tags with a different Facility Code than you

originally programmed into the reader. The RK-65K can learn

up to 10 different Facility Codes. If it becomes necessary to mix

transponders with more than one Facility Code in the same reader,

be sure that the transponder ID numbers are not duplicated.

NOTE: RKxx-01 cards or keytags will not work for the

RK65K. The LED will flash amber to let you

know it is the wrong type of card.

Radio Key

®

RK-65K Operating Guide

Secura Key  4

PROGRAMMING RADIO KEY

®

RK-65K

When the RK-65K is ﬁ rst powered up, the LED will be ﬂ ashing

Red and Green. Present a card to the unit to set the Facility

Code and the ﬂ ashing will end in approximately 10 seconds.

Radio Key Transponders (Key tags and cards) are pre-encoded

and engraved at the factory with a Facility (Site) Code and an

individual card ID number.

You must teach the RK-65K which Facility Code or Codes

(up to 10) it should recognize. You must also enroll the card

ID numbers that will be Valid. The Radio Key

®

cards and tags

are sequentially numbered, so you can validate a block of

transponders.

Be sure to make a record of each person who is issued a

transponder along with the ID number of their card or tag.

Radio Key

®

RK-65K Operating Guide

Secura Key  5

PROGRAMMING RADIO KEY

®

100M

Radio Key

®

Transponders (Key Tags and Cards) are pre-en-

coded and engraved at the factory with unique Transponder ID

numbers. Because these numbers are unique, Facility Codes

(Site Codes) are not required.

Transponder ID Numbers are not pre-programmed into the Radio

Key

®

100M; you must add them to the system as described below.

Radio Key

®

100M allows you to assign a Transponder to each

User ID Number (1 - 100) for programming purposes. The

User ID Number is associated with the individual person using

the transponder.

Be sure to record the User ID Number, the Transponder

ID Number and the user’s name, and keep this informa-

tion in a secure place. A blank User Log Form has been

included for this purpose. Do not write on this form; use it as

a photocopy master.

Because a new Transponder ID Number can be assigned to

any available User ID Number, the reader always has capac-

ity to store 100 Transponders, even after many Transponders

have been voided from the reader.

Radio Key

®

RK-65K Operating Guide

Secura Key  6

THE RK-HHP HANDHELD PROGRAMMER AND THE

RK-PD1 PROGRAM DECK

Note: The RK-PD1 or the RK-HHP is required to program

the reader. One RK-PD1 or RK-HHP may be used on

several readers.

The RK-PD1 consists of the 16 following cards:

ENTER “7” SEVEN

“0” ZERO “8” EIGHT

“1” ONE “9” NINE

“2” TWO “ ” THRU

“3” THREE “ ” VALID

“4” FOUR

“ ”

VOID

“5” FIVE SET TIMER

“6” SIX MODE

Presenting these cards to the Radio Key

®

RK-65K is equivalent

to pressing the identically marked keys on the RK-HHP hand-

held programmer. As you present program cards to the unit, it

will chirp to indicate that it has read the card. The next sections

of this manual explain the program card sequences used to

perform the various program functions.

PROGRAMMING STEPS

To program the Radio Key

®

RK-65K, you must ﬁ rst enter the

program mode as described in the next section below. Once in

the program mode, the LED will blink amber as an indicator. To

take the unit out of program mode you may select an operating

mode (see page 14) or simply allow 15 seconds to elapse without

presenting a program card to the reader.

After you have completed a proper program sequence, the

unit will beep and the LED will ﬂ ash green to indicate that the

program instruction has been accepted. A red light and a beep

at the end of a programming sequence means that you have

made an error. Refer to the appropriate section, and carefully

re-enter the command in the proper sequence.

NOTE: User ID Number and ID Number Values in

the following examples are for demonstration

purposes only; enter the appropriate values for

your system.

Radio Key

®

RK-65K Operating Guide

Secura Key  7

(Password)

(ENTER)

To Enter Program Mode (RK65K/RK100M):

Using your programmer, enter your password and then press

“ENTER”. (All new units are pre-programmed with the password

12345.) The LED will ﬂ ash amber to show that the unit is in

Program Mode. The unit will “time out” and return to Active

(Normal) Mode in 15 seconds if no programming follows.

1 + 2 + 3 + 4 + 5 +

NOTE: If ﬁ ve incorrect passwords are entered, the unit will

sound an alarm and display a red LED for 30 seconds, then

return to normal mode.

Change your Password (RK65K/RK100M):

Put the unit into the Program mode, if necessary (See above).

Press THRU. Then enter the sequence of digits representing

the desired new password (exactly 5 digits). Then press THRU

again. Repeat the new password. Press ENTER. A green light

and beep means that the Password was changed. Note that

12345 is the default (factory) password; use another number

sequence for best security.

Radio Key

®

RK-65K Operating Guide

Secura Key  8

(New Password - 54321)

(Re-type New Password - 54321)

(ENTER)

(THRU)

Radio Key

®

RK-65K Operating Guide

Secura Key  9

+ 5 + 4 + 3 + 2 + 1 +

Lost or forgotten Password (RK65K/RK100M)

If the password is lost or forgotten, it can be restored to the

factory default (12345). Remove the Radio Key

®

RK-65K

unit from the wall and disconnect power. With the Data 1 line

(white wire) temporarily connected to the Remote open line

(brown wire), restore power. The factory default (12345) is

now in effect. The LED will ﬂ ash alternately Red and Green.

While this is occurring, set the Facility Code or Codes in the

reader (see below). Remove power and reconnect the unit for

operation, restore power and remount the unit. This procedure

will NOT delete any transponders from reader’s memory.

Setting Facility Code(s) (RK65K)

Before any cards are added to the RK-65K you must set the

Facility Code or Codes. When a new reader is ﬁ rst powered

up the LED should be ﬂ ashing alternately Red and Green. This

indicates that the unit is in the “Learn Facility Code” mode.

(User ID Number 12)

(ADD)

(ENTER)

(MODE)

(ENTER)

(Mode Number 9)

Radio Key

®

RK-65K Operating Guide

Secura Key  10

You can also place a reader in this mode by entering the

Program Mode (see page 8) then pressing Mode followed by

“9” followed by Enter.

+ 9 +

While the LED is ﬂ ashing Red/Green present one User

Card for each Facility Code being used to the reader, one

at a time. After you are ﬁ nished, allow the reader to time

out and return to the Normal Mode before proceeding.

NOTE: An invalid facility code will beep with no LED visible.

ADDING AND DELETING USERS (RK65K)

Add A Transponder (Key Tag or Card) To The System:

Place the unit in the Program Mode (See Page 8). Press Add,

followed by the sequence of digits representing the Transponder

ID number. Then press Enter. For example, to add transponder

#12 to the reader the following sequence would be followed:

+ 1 + 2 +

Transponder number 12 is now valid.

Radio Key

®

RK-65K Operating Guide

Secura Key  11

(Ending User ID

Number 10)

(ADD)

(ENTER)

(Starting

User No. 1)

(THRU)

(User ID Number 12) (ENTER)(VOID)

Add A Series Of Transponders To The System (RK65K):

Place the unit into the Program mode (see Page 8). Press Add,

followed by the sequence of digits representing the lowest

transponder ID number. Then press Thru, followed by the

sequence of digits representing the highest transponder ID

number. Then press Enter. For example, to add transponders

#1 through #10 to the system:

+ 1 + + 1 + 0 +

Transponder number 1 through 10 are now valid.

Delete A Transponder From The System (RK65K):

Place the unit in the Program Mode (see Page 8). Press Void,

followed by the sequence of digits representing the transponder

ID number. Then press Enter. For example, to delete transponder

#12, the following sequence would be presented:

+ 1 + 2 +

Transponder #12 is now void.

(SET TIMER)

(ENTER)

(15 Seconds)

Radio Key

®

RK-65K Operating Guide

Secura Key  12

(Ending User ID

Number 10)

(ENTER)

(VOID)

(THRU)

(Starting

User No. 1)

Delete A Series Of Transponders From The System (RK65K):

Place the unit in the Program Mode (see Page 8). Press Void,

followed by the sequence of digits representing the lowest

transponder ID. Then press Thru followed by the sequence of

digits representing the highest number transponder. Finally, press

Enter. For example, to delete transponders #1 through #10:

+ 1 + + 1 + 0 +

Transponders #1 through #10 are now void.

Set the Latch Timer (RK65K/RK100M):

Put the unit into the Program mode, (See Page 8). Press SET

TIMER, then press the sequence of digits representing the desired

Latch Time (0 - 65535 seconds) to the unit. Press ENTER. A

green light and beep means that the Latch Timer setting was

changed. (If you set the Latch Timer for “0” seconds, the actual

latch time will be approximately 0.25 seconds.) For example,

to set the latch timer to 15 seconds, the following sequence

would be followed;

+ 1 + 5 +

Radio Key

®

RK-65K Operating Guide

Secura Key  13

(SET TIMER)

(ENTER)

(2 Hours, 45 Minutes)

(THRU)

For longer latch times it may be easier to set the timer with hour:

minute notation. Press SET TIMER; then press the sequence of

digits representing the number of hours (2 digits); then press the

sequence of digits representing the number of minutes; then press

THRU; then ENTER. (The maximum relay time is 18 hours and

00 minutes.) For example, to set the latch timer for 2 hours and

45 minutes the following sequence would be followed:

+ 0 + 2 + 4 + 5 + +

If you have set an extended latch time, but need to interrupt it,

follow this procedure. Put the unit in Program Mode (see Page 8).

Then press Set Timer then “1” then Enter. After the Program

Mode expires, present a valid card to the reader. After one

second the relay will return to it’s normal state. You will then

have to reprogram the latch timer to the desired duration.

PROGRAMMING HINTS:

Setting the Latch Timer (RK65K/RK100M):

The latch timer controls the latch relay. The factory preset latch time

is 1 second but it can be changed to any value from .25 seconds

to 18 hours. If the latch timer is set to 0 seconds, this pulses the

latch relay for 0.25 second, sufﬁ cient for most electric turnstiles.

The beeper and LED are always ﬁ xed at one second.

Radio Key

®

RK-65K Operating Guide

Secura Key  14

Set the Operating Mode (RK65K/RK100M):

The Radio Key

®

RK-65K may be put into any of four operational

modes. The Modes are as follows;

“1” - Active (Normal) -- LED is Off

“2” - Inactive (Locked) -- LED blinks Red

“3” - Door Unlocked -- LED blinks Green

“4” - Toggle Mode – LED is Off

In mode 1, a valid tag or closure of the remote open input will

activate the relay for the time the latch timer is set.

Mode 2 deactivates the unit. No tag can activate the relay, but

the remote open input will activate the relay.

In mode 3, the door is kept unlocked (the relay is kept latched).

In mode 4, when a valid tag is presented or the remote open

input is activated, the relay changes its state from deactivated

to activated or from activated to deactivated. The relay will stay

in this state until another valid tag is presented or the remote

input is activated and so forth.

(MODE)

(ENTER)

(Mode Number 1)

Radio Key

®

RK-65K Operating Guide

Secura Key  15

(Mode Number 2)(MODE)

(ENTER)

To set the Operating Mode, put the unit into the Program mode,

(See Page 8). Press MODE, then press either “1” , “2”, “3”, or “4”.

Press ENTER. The Access Control Unit will exit Programming

Mode and enter the selected Mode. For example, to set the

unit to the inactive (locked) mode, the following sequence

would be followed;

+ 2 +

To Exit Programming Mode Immediately (RK65K/RK100M):

Press MODE, then “1” (or 2, 3, or 4) card to the unit. Press

ENTER. This returns the unit to the selected mode immediately,

bypassing the 15 second timeout.

+ 1 +

Timed Antipassback(RK65K)

Timed antipassback is used to discourage card sharing. After

one successful card use, the unit will treat that card as Void

for a preset number of minutes. When timed antipassback is

enabled, it will apply to all valid cards.

(SET TIMER)

(ENTER)

(THRU)

(SET TIMER)

(ENTER)

(ADD)

Radio Key

®

RK-65K Operating Guide

Secura Key  16

(SET TIMER)

(ENTER)

(VOID)

Enable Timed Antipassback (RK65K):

Place the unit in the Program Mode (see Page 8). Press SET

TIMER, then press ADD, ﬁ nally press ENTER.

+ +

Set Antipassback Timer (RK65K):

Place the unit in the Program Mode (see Page 8). Press SET

TIMER then press THRU. Press the digits representing the

maximum number of minutes you want antipassback to apply

(01 – 99). Press ENTER. (Antipassback can be from one to

ninety-nine minutes. Depending upon the clock cycle of the

unit when a card is read, the actual antipassback time may be

as little as one-half the time selected.)

+ + 1 + 5 +

Disable Timed Antipassback (RK65K):

Place the unit in the Program Mode (see Page 8). Press SET

TIMER then VOID, ﬁ nally press ENTER.

+ +

(ENTER)(THRU)

(THRU)

Radio Key

®

RK-65K Operating Guide

Secura Key  17

Conﬁ gure the Relay (RK65K/RK100M)

The relay is set at the factory to be normally open and to close

upon presentation of a valid transponder or upon activation of

the remote open (Request to Exit) input. It may be changed to

normally closed or to SecuRelay™ operation. A normally open

relay is used for a “fail-secure” electric lock or door strike and

to trigger a gate operator. A normally closed relay is used for

“fail-safe” devices such as magnetic locks. The Secura Key

SecuRelay™ (sold separately) is a remote intelligent relay

used to prevent entry when the access control unit is physically

attacked. (NOTE: When placed in the SecuRelay™ mode the

“Remote Open” input is disabled.) To conﬁ gure the relay, put

the unit in the Program mode (See Page 8). Press THRU two

times. Then press either the “6”, “7” or “8”. Press ENTER.

Selections are:

6. Normally Open (Factory default)

7. Normally Closed

8. SecuRelay™ Option.

For example, to configure the relay normally closed, the

following sequence would be followed:

+ + 7 +

Page is loading ...

SoundCraft RK100M User manual

This manual is also suitable for

SoundCraft RK100M User manual

Related papers

Other documents