Allen-Bradley 1738-ADNX User manual

User Manual

(Catalog Numbers

1734-8CFGDLX,

1738-8CFGDLXM8, 1738-8CFGDLXM12, 1738-8CFGDLXM23)

POINT I/O and ArmorPOINT I/O

DeviceLogix Modules

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the

Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell Automation sales

office or online at http://literature.rockwellautomation.com

) describes some important differences between solid state equipment and hard-

wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all

persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or

application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements

associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the

examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in

this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

Allen-Bradley, ArmorPOINT I/O, POINT I/O, POINTBus, Rockwell Automation, RSLogix, RSNetWorx, RSNetWorx for DeviceNet, and TechConnect are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

WARNING

Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage, or

economic loss.

IMPORTANT

Identifies information that is critical for successful application and understanding of the product.

ATTENTION

Identifies information about practices or circumstances that can lead to personal injury or death,

property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and

recognize the consequence

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

dangerous voltage may be present.

BURN HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert people that

surfaces may reach dangerous temperatures.

1 Publication 1734-UM015A-EN-E - November 2009

Table of Contents

Preface

Purpose of This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Who Should Use This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 1

Introduction

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

About the Modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1734-8CFGDLX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

1738-8CFGDLXM8, 1738-8CFGDLXM12, and

1738-8CFGDLXM23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Modes of Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Standard POINT I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Stand Alone DeviceLogix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Peer Enabled POINT I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Quick Start - Prepare the Modules to work on DeviceNet . . . . . . . . . 12

Quick Start - Prepare the Modules to work on EtherNet/IP and

ControlNet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Chapter 2

Install POINT I/O DeviceLogix

Modules

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Install the Mounting Base Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Install an I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Install the Removable Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . 21

Remove a 1734-TB or 1734-TBS Base . . . . . . . . . . . . . . . . . . . . . . . . . 22

Remove a 1734-TOP or 1734-TOPS Base . . . . . . . . . . . . . . . . . . . . . . 23

Wire the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1734-8CFGDLX I/O Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

1734-8CFGDLX Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 24

System and Power Considerations . . . . . . . . . . . . . . . . . . . . . . . . . 25

Chapter 3

Install ArmorPOINT I/O

DeviceLogix Modules

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Install the Mounting Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Install the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Remove the Module from the Mounting Base. . . . . . . . . . . . . . . . 30

Wire the Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1738-8CFGDLXM8 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . . 30

1738-8CFGDLXM12 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . 31

1738-8CFGDLXM23 I/O Module . . . . . . . . . . . . . . . . . . . . . . . . 32

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

2 Table of Contents

Chapter 4

DeviceLogix for POINT I/O and

ArmorPOINT I/O on DeviceNet

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Offline Configuration using RSNetworx for DeviceNet . . . . . . . . . . . 33

Example: Build the Backplane . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Online Configuration using RSNetWorx for DeviceNet. . . . . . . . . . . 36

I/O Data Assembly Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Chapter 5

DeviceLogix for POINT I/O and

ArmorPOINT I/O on

Ethernet/ControlNet

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Add a POINT I/O DeviceLogix Module to RSLogix 5000 . . . . . . . . 43

I/O Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Launch RSNetworx for DeviceNet to Configure the Module. . . . . . . 47

Chapter 6

Configuring POINT I/O and

ArmorPOINT I/O DeviceLogix

modules using RSNetworx for

DeviceNet

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Configure the Module using the Configuration tab . . . . . . . . . . . . . . . 49

Parameters on the Parameters tab. . . . . . . . . . . . . . . . . . . . . . . . . . 53

Configure Peer Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Set Up Peer Communication Parameters . . . . . . . . . . . . . . . . . . . . 55

Produce Data Without Using a Master . . . . . . . . . . . . . . . . . . . . . . . . . 58

Start the Function Block Editor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Chapter 7

DeviceLogix Capabilities

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Function Block Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Process Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Filter Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Select Limit Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Statistical Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Timer/Counter Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Comparison Category . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Compute Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Move/Logical Category. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Logic Execution Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Digital Inputs to Function Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . 71

Analog Inputs to Function Blocks . . . . . . . . . . . . . . . . . . . . . . . . . 73

Digital Outputs from Function Blocks. . . . . . . . . . . . . . . . . . . . . . 74

Analog Outputs from Function Blocks . . . . . . . . . . . . . . . . . . . . . 76

Enable Line feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Offline and Online Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Enable/Disable Logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Logic Enable On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Logic Enable Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Dependent Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Publication 1734-UM015A-EN-E - November 2009

Table of Contents 3

Chapter 8

Troubleshooting

About This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

About Module Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Status Indicators of POINT I/O Module . . . . . . . . . . . . . . . . . . . . . . 84

1734-8CFGDLX Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Status Indicators of ArmorPOINT I/O Modules . . . . . . . . . . . . . . . . 86

1738-8CFGDLXM8, 1738-8CFGDLXM12, and

1738-8CFGDLXM23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Troubleshooting Scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Peer connection is not working. . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

Configuration or DeviceLogix program cannot be

downloaded to the module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

Module’s DeviceLogix program exits the Run mode

unexpectedly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Appendix A

Peer Data Maps

About This Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Peer I/O Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Digital Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Analog and Specialty Input Modules . . . . . . . . . . . . . . . . . . . . . . . 92

Peer Data Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

2-Point Digital Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

4-Point Digital Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

4-Point Digital Input with Diagnostics Modules . . . . . . . . . . . . . . 95

8-Point Digital Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

8-Point Configurable Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

16-Point Digital Input Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

8-Point Digital Input Modules with DeviceLogix . . . . . . . . . . . . . 97

2-Point Analog Input Modules and RTD (Resistant

Temperature Device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

4-Point Analog Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

8-Point Analog Input Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

2-Point Thermocouple Input Modules. . . . . . . . . . . . . . . . . . . . . 102

Very High Speed Counter Input Modules . . . . . . . . . . . . . . . . . . 103

Encoder/Counter Input Modules. . . . . . . . . . . . . . . . . . . . . . . . . 105

Synchronous Serial Interface Modules . . . . . . . . . . . . . . . . . . . . . 105

RS232 and RS485 Interface Module . . . . . . . . . . . . . . . . . . . . . . . 106

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

4 Table of Contents

Notes:

5 Publication 1734-UM015A-EN-E - November 2009

Preface

Purpose of This Manual

This manual describes how to install, configure, and troubleshoot your

POINT I/O DeviceLogix and ArmorPOINT I/O DeviceLogix modules.

POINT I/O and ArmorPOINT I/O modules can be used in EtherNet/IP,

DeviceNet, and ControlNet systems. As such, you may need to refer to other

publications in addition to this one.

When using POINT I/O DeviceLogix modules with a communication

adapter, use this manual in conjunction with the user manual for the adapter

you are using as shown in the table.

POINT I/O DeviceLogix modules are not compatible with the PROFIBUS

adapter.

When using ArmorPOINT I/O DeviceLogix modules with a communication

adapter, use this manual in conjunction with the user manual for the adapter

you are using as shown in the table.

ArmorPOINT I/O DeviceLogix modules are not compatible with the

PROFIBUS adapter.

The modules in this manual are DeviceNet-ready. Each module can exist on

the DeviceNet network as one of the following:

• An individual node

• With an adapter (catalog number 1734-ADN or 1734-ADNX) as a

single node

For applications using these modules in a network with a 1734-PDN

DeviceNet Communication Interface, or a 1734D-xx POINTBlock I/O

module, this user manual is the primary documentation.

When Using POINT I/O

Modules on This Network

Refer to

Publication for

Catalog No. Publication No.

DeviceNet network DeviceNet adapter 1734-ADN

1734-ADNX

1734-UM002

ControlNet network ControlNet adapter 1734-ACNR 1734-UM008

EtherNet/IP network EtherNet/IP adapter 1734-AENT 1734-UM011

When Using ArmorPOINT

I/O Modules on This

Network

Refer to

Publication for

Catalog No. Publication No.

DeviceNet network DeviceNet adapter 1738-ADN

1738-ADNX

1738-UM001

ControlNet network ControlNet adapter 1738-ACNR 1738-IN016

EtherNet/IP network EtherNet/IP adapter 1738-AENT

1738-AENTR

1738-IN017

1738-IN028

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

6 Preface

Who Should Use This

Manual

This manual is intended for qualified personnel. You should know how to do

the following:

• Use RSNetWorx software or similar configuration software to set up

and calibrate these modules.

• Download and use electronic data sheet (EDS) files.

In addition, you should be familiar with RSLogix 5000 and CIP Network

terminology. If you do not, refer to your software documentation or online

help before attempting to use these modules.

Related Publications

Refer to this table for a list of related POINT I/O products and

documentation. The publications are available from

http://literature.rockwellautomation.com/

. For specification and safety

certification information, refer to the installation instructions.

Resource Description

POINT I/O DeviceLogix Module

POINT I/O Module with 8 Configurable 24V DC Points and

DeviceLogix Installation Instructions, publication 1734-IN039

Provides installation information and wiring diagrams for

1734-8CFGDLX modules.

Communication Devices

ControlNet Adapter Installation Instructions,

publication 1734-IN582

Provides installation information about 1734-ACNR adapters.

ControlNet Adapter User Manual, publication 1734-UM008

Describes how to use 1734-ACNR adapters.

DeviceNet Communication Interface Module Installation

Instructions, publication 1734-IN057

Provides installation information about 1734-PDN modules.

DeviceNet Adapter Installation Instructions, publication 1734-IN026

Provides installation information about 1734-ADN and 1734-ADNX

adapters.

DeviceNet Adapter User Manual, publication 1734-UM002

Describes how to use 1734-ADN and 1734-ADNX adapters.

RSNetworx for DeviceNet Getting Results Guide, publication

DRNET-GR001

Describes how to install and navigate the RSNetWorx for

DeviceNet software.

EtherNet/IP Adapter Installation Instructions,

publication 1734-IN590

Provides installation information about 1734-AENT adapters.

EtherNet/IP Adapter User Manual, publication 1734-UM011

Describes how to use 1734-AENT adapters.

Power Supplies, Wiring Base Assemblies, Miscellaneous

Field Potential Distributor Installation Instructions,

publication 1734-IN059

Provides installation information about 1734-FPD distributors.

POINT I/O 24V dc Expansion Power Supply Installation Instructions,

publication 1734-IN058

Provides installation information about 1734-EP24DC power

supplies.

POINT I/O 120/240V ac Expansion Power Supply Installation

Instructions, publication 1734-IN017

Provides installation information about 1734-EPAC power supplies.

POINT I/O Common Terminal Module Installation Instructions,

publication 1734-IN024

Provides installation information about 1734-CTM modules.

Publication 1734-UM015A-EN-E - November 2009

Preface 7

Refer to this table for a list of related ArmorPOINT I/O products and

documentation. The publications are available from

http://literature.rockwellautomation.com/

. For specification and safety

certification information, refer to the installation instructions.

POINT I/O Voltage Terminal Module Installation Instructions,

publication 1734-IN024

Provides installation information about 1734-VTM modules.

POINT I/O Wiring Base Assembly Installation Instructions,

publication 1734-IN511

Provides installation information about 1734-TB and 1734-TBS

assemblies.

POINT I/O Wiring Base Assembly Installation Instructions,

publication 1734-IN013

Provides installation information about 1734-TB3 and 1734-TB3S

assemblies.

POINT I/O One-piece Wiring Base Assembly Installation

Instructions, publication 1734-IN028

Provides installation information about 1734-TOP, 1734-TOPS,

1734-TOP3 and 1734-TOP3S assemblies.

Resource Description

ArmorPOINT I/O DeviceLogix Module

ArmorPOINT I/O Modules with 8 Configurable 24V DC Points Wiring

Diagrams, publication 1738-WD009

Provides wiring diagrams for 1738-8CFGDLXM8,

1738-8CFGDLXM12, and 1738-8CFGDLXM23.

ArmorPOINT Module with Configurable 24V DC Points and

DeviceLogix Installation Instructions, publication 1738-IN027

Provides installation information about 1738-8CFGDLXM8,

1738-8CFGDLXM12, and 1738-8CFGDLXM23.

Communication Devices

ArmorPOINT ControlNet Adapter, Series A Installation Instructions,

publication 1738-IN016

Provides installation information about 1738-ACNR adapters.

ArmorPOINT I/O DeviceNet Adapter Installation Instructions,

publication 1738-IN014

Provides installation information about 1738-ADN and 1738-ADNX

adapters.

ArmorPOINT I/O DeviceNet Adapter User Manual, publication

1738-UM001

Describes how to use 1738-ADN and 1738-ADNX adapters.

ArmorPOINT EtherNet/IP Adapter, Series A Installation Instructions,

publication 1738-IN017

Provides installation information about 1738-AENT adapters.

ArmorPOINT I/O 2-Port EtherNet/IP Adapter, Series A Installation

Instructions, publication 1738-IN028

Provides installation information about 1738-AENTR adapters.

Power Supplies, Wiring Base Assemblies, Miscellaneous

ArmorPOINT I/O Field Potential Distributor, Series A Installation

Instructions, publication 1738-IN019

Provides installation information about 1738-FPD distributors.

ArmorPOINT I/O 24V dc Expansion Power Supply, Series A

Installation Instructions, publication 1738-IN020

Provides installation information about 1738-EP24DC power

supplies.

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

8 Preface

Notes:

9 Publication 1734-UM015A-EN-E - November 2009

Chapter

1

Introduction

About This Chapter

This chapter introduces POINT I/O and ArmorPOINT I/O configurable

modules with DeviceLogix capability.

• About the Modules

• Quick Start - Prepare the Modules to work on DeviceNet

• Quick Start - Prepare the Modules to work on EtherNet/IP and

ControlNet

About the Modules

The POINT I/O and ArmorPOINT I/O modules work with EtherNet/IP,

DeviceNet and ControlNet network adapters. Each module has eight 24V DC

I/O points that self-configure to be inputs or outputs. Inputs are IEC Type 3

and outputs are self-protecting 0.5 A outputs.

The firmware in these modules uses Version 3 of the DeviceLogix master

library. The modules can execute 144 DeviceLogix function blocks in 3 ms.

Smaller programs that contain fewer than 40 function blocks can be executed

in 1 ms.

Each module produces 20 bytes of data including I/O state (eight bits), eight

user-defined bits, and eight user-defined words of analog data to be consumed

by processors or other DeviceLogix modules. Each module consumes 20 bytes

of data to set the I/O state (eight bits), eight user-defined control bits, and

eight user-defined words of analog data. It is also possible to consume the data

from up to eight other peers.

This table lists 1734 and 1738 configurable I/O modules with DeviceLogix.

Module Description Cat. No.

POINT I/O module with 8 configurable 24V DC I/O points

and DeviceLogix capabilities

1734-8CFGDLX

ArmorPOINT I/O module with 8 configurable 24V DC M8

connectors and DeviceLogix

1738-8CFGDLXM8

ArmorPOINT I/O module with 8 configurable 24V DC M12

connectors and DeviceLogix

1738-8CFGDLXM12

ArmorPOINT I/O module with 1 configurable 24V DC M23

connector and DeviceLogix

1738-8CFGDLXM23

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

10 Introduction

1734-8CFGDLX

This module is an 8-point 24V DC I/O module with 8 self-configuring points

and DeviceLogix capabilities. Each of the I/O points can be either a DC input

or output. The module supports removal and insertion under power,

auto-address, and auto-baud in compliance with the POINTBus backplane.

1738-8CFGDLXM8, 1738-8CFGDLXM12, and 1738-8CFGDLXM23

The ArmorPOINT I/O family consists of modular I/O modules. The sealed

IP67 housing of these modules requires no enclosure. Note that

environmental requirements other than IP67 may require an additional

appropriate housing. I/O connectors are sealed M8 (pico), M12 (micro) or

M23 styles. The mounting base ships with the module.

Modes of Usage

The module can be used in one of the following modes:

• as a standard POINT I/O module,

• in a stand alone DeviceLogix program where it controls its own I/O,

and

• in network applications with or without the peer exchange of data.

Standard POINT I/O Module

The module can simply be used as an 8-point configurable POINT I/O

module. It uses ODVA pre-defined Produce and Consume assemblies. Default

settings help to facilitate quick setup right out-of-the-box. It is CIP network

independent and it can run on DeviceNet, EtherNet/IP or ControlNet when

used in conjunction with an adapter.

Publication 1734-UM015A-EN-E - November 2009

Introduction 11

Stand Alone DeviceLogix

If DeviceLogix is enabled (programmed), then the module becomes the owner

of its outputs. The DeviceLogix program reads inputs and controls the

onboard outputs.

• The produced assembly may be shared with a controller if a connection

exists.

• As the owner of its local outputs, the module may run without an

external controller.

An external controller, which is the owner of the connection to the module,

can influence the module’s logic via a consume assembly – both digital and

analog data. Configuration of the module is performed via RSNetWorx for

DeviceNet. When used on ControlNet or EtherNet/IP, the tool bridges

through the adapter to directly communicate with the DeviceLogix module on

the POINT I/O backplane.

Peer Enabled POINT I/O

The POINT I/O DeviceLogix module can “listen in” on data connections to

other POINT I/O modules on the backplane. This data can be used in the

DeviceLogix program to control the outputs. It can consume data from 8

different peers. The data from each peer can be up to 24 bytes long. The data

can be digital, analog (16-bit), or a mixture. The module supports the “Auto

Produce” parameter to produce I/O data automatically without the need for a

master. It will also produce and consume network data. Configuration of peer

data is performed via RSNetWorx.

See Chapter 6,

Configuring POINT I/O and ArmorPOINT I/O DeviceLogix

modules using RSNetworx for DeviceNet.

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

12 Introduction

Quick Start - Prepare the

Modules to work on

DeviceNet

Mount the Module

For POINT I/O, see Chapter 2

.

For ArmorPOINT I/O, see Chapter 3

.

Wire the Module

For POINT I/O, see Chapter 2

.

For ArmorPOINT I/O, see Chapter 3

.

Configure DeviceNet Network and

Scanner

See Chapter 4

.

Configure the Module using

RSNetWorx for DeviceNet

See Chapter 6

.

Write the DeviceLogix Program

See Chapter 7

.

Publication 1734-UM015A-EN-E - November 2009

Introduction 13

Quick Start - Prepare the

Modules to work on

EtherNet/IP and ControlNet

Mount the Module

For POINT I/O, see Chapter 2

.

For ArmorPOINT I/O, see Chapter 3

.

Wire the Module

For POINT I/O, see Chapter 2

.

For ArmorPOINT I/O, see Chapter 3

.

Add Module to RSLogix 5000

See Chapter 5

.

Write the DeviceLogix Program in

RSNetworx for DeviceNet

See Chapter 7

.

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

14 Introduction

Notes:

15 Publication 1734-UM015A-EN-E - November 2009

Chapter

2

Install POINT I/O DeviceLogix Modules

If you are using ArmorPOINT I/O modules

(1738-8CFGDLXM8/M12/M23), go to Chapter 3,

Install ArmorPOINT I/O

DeviceLogix Modules.

About This Chapter

Read this chapter for installation and wiring information including how to

complete the following:

• Install the Mounting Base Assembly

• Install an I/O Module

• Install the Removable Terminal Block

• Remove a 1734-TB or 1734-TBS Base

• Wire the Modules

ATTENTION

Environment and Enclosure

This equipment is intended for use in a Pollution Degree 2

industrial environment, in overvoltage Category II applications

(as defined in IEC publication 60664-1), at altitudes up to 2000 m

(6561 ft) without derating.

This equipment is considered Group 1, Class A industrial

equipment according to IEC/CISPR 11. Without appropriate

precautions, there may be potential difficulties ensuring

electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be

mounted within an enclosure that is suitably designed for those

specific environmental conditions that will be present and

appropriately designed to prevent personal injury resulting from

accessibility to live parts. The interior of the enclosure must be

accessible only by the use of a tool. Subsequent sections of this

publication may contain additional information regarding specific

enclosure type ratings that are required to comply with certain

product safety certifications.

See NEMA Standards 250 and IEC 60529, as applicable, for

explanations of the degrees of protection provided by different

types of enclosure. Also, see the appropriate sections in this

publication, as well as the Allen-Bradley publication 1770-4.1

(Industrial Automation Wiring and Grounding Guidelines), for

additional installation requirements pertaining to this equipment.

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

16 Install POINT I/O DeviceLogix Modules

ATTENTION

POINT I/O is grounded through the DIN rail to chassis ground.

Use zinc-plated, yellow-chromated steel DIN rail to assure proper

grounding. The use of DIN rail materials (for example, aluminum

or plastic) that can corrode, oxidize, or are poor conductors, can

result in improper or intermittent grounding.

Secure DIN rail to mounting surface approximately every 200

mm (7.8 in.).

WARNING

EXPLOSION HAZARD

• Do not disconnect equipment unless power has been

removed or the area is known to be nonhazardous.

• Do not disconnect connections to this equipment unless

power has been removed or the area is known to be

nonhazardous. Secure any external connections that mate to

this equipment by using screws, sliding latches, threaded

connectors, or other means provided with this product.

• Substitution of components may impair suitability for Class I,

Division 2.

• If this product contains batteries, they must only be changed

in an area known to be nonhazardous.

ATTENTION

Prevent Electrostatic Discharge

This equipment is sensitive to electrostatic discharge, which can

cause internal damage and affect normal operation. Follow these

guidelines when you handle this equipment:

• Touch a grounded object to discharge potential static.

• Wear an approved grounding wriststrap.

• Do not touch connectors or pins on component boards.

• Do not touch circuit components inside the equipment.

• Use a static-safe workstation, if available.

• Store the equipment in appropriate static-safe packaging when

not in use.

Publication 1734-UM015A-EN-E - November 2009

Install POINT I/O DeviceLogix Modules 17

Install the Mounting Base

Assembly

The 1734-8CFGDLX is compatible with 1734-TB, 1734-TBS, 1734-TOP, and

1734-TOPS wiring bases.

The 1734-TB or 1734-TBS wiring base assembly consists of a 1734-MB

mounting base and a 1734-RTB or 1734-RTBS removable terminal

block (RTB).

1734-TB or 1734-TBS wiring base

The 1734-TOP and 1734-TOPS are one-piece terminal bases.

1734-TOP or 1734-TOPS wiring base

Module

Status

Network

Status

NODE:

0

1

2

3

4

5

6

7

Mechanical

Keying (orange)

Module Wiring

Diagram

Module Locking

Mechanism

Insertable I/O

Module

Mounting Base

Removable

Terminal Block

(RTB)

DIN Rail Locking

Screw (orange)

Slide-in Writable

Label

Interlocking Side

Pieces

44713

RTB Removal

Handle

44714

1734-TOP or

1734-TOPS

One-piece

Terminal Base

with Screw or

Spring Clamp

Insertable

I/O Module

Slide-in

Writable Label

Handle

Module Locking

Mechanism

Interlocking

Side Pieces

DIN Rail Locking

Screw (orange)

Module Wiring

Diagram

Mechanical

Keying (orange)

Allen-Bradley HMIs

Publication 1734-UM015A-EN-E - November 2009

18 Install POINT I/O DeviceLogix Modules

To install the mounting base assembly on the DIN rail, proceed as follows.

1. If you are using the 1734-TB or 1734-TBS mounting base, attach the

RTB to the mounting base.

Otherwise, skip to step 2.

2. Position the mounting base (wiring base assembly) vertically above the

installed units, for example, adapter, power supply, or existing module.

3. Slide the mounting base down, allowing the interlocking side pieces to

engage the adjacent module, power supply, or adapter.

4. Press firmly to seat the mounting base on the DIN rail until the base

snaps into place.

5. Use a small-bladed screwdriver to rotate the DIN-rail locking screw to

the horizontal position.

This locks the assembly to the DIN rail.

44858

Removable

Terminal Block

(RTB)

Mounting Base

31586

Page is loading ...

Allen-Bradley 1738-ADNX User manual

This manual is also suitable for

Allen-Bradley 1738-ADNX User manual

Related papers

Other documents