Powermate PMC606750 User manual

Brand: Powermate

Model: PMC606750

Category: Power generators

Type: User manual

Page is loading ...

*12 HP Yamaha OHV engine

*Cast-iron cylinder sleeve

*Low oil sensor

*Receptacles on control panel

*DIGITECH™ Digital Information Center

*7 gallon metal fuel tank

*Spark arrester

*Portability Kit

A.120 Volt GFCI Receptacle

Ground Fault Circuit Interrupter duplex receptacle is rated

so that a total of 20 amps may be drawn regardless of whether

both halves or just one receptacle is used. This receptacle may

be used along with other receptacles provided the generator is

not overloaded and total power drawn is kept within nameplate

ratings.

Ground Fault Circuit Interrupter

(Conforms to U.L 943, Class A and NEC requirements)

This device protects you against hazardous electrical shock

that may be caused if your body becomes a path through which

electricity travels to reach ground. This could happen when

you touch an appliance or cord that is “ live “ through faulty

mechanism, damp or worn insulation, etc.

B.120/240 V, 30 Ampere Twistlock Receptacle

A maximum of 30 amps may be drawn from the 120/240

volt receptacle, provided it is the only receptacle used.

However, current must be limited to the nameplate rating. If the

120/240 volt receptacle is used along with the 120 volt

receptacle, the total load drawn must not exceed the nameplate

ratings.

C.Circuit Breakers

The receptacles are protected by an AC circuit breaker. If

the generator is overloaded or an external short circuit occurs,

the circuit breaker will trip. If this occurs, disconnect all

electrical loads and try to determine the cause of the problem

before attempting to use the generator again. If overloading

causes the circuit breaker to trip, reduce the load. NOTE:

Continuous tripping of the circuit breaker may cause

damage to generator or equipment. The circuit breaker may

be reset by pushing the button of the breaker.

D.Engine On/Off Switch

E.DIGITECH™ Digital Information Center

The DIGITECH™ Digital Information Center is a patented

feature available only on select Coleman® Powermate® Brand

generators.

At a glance, the user can instantly see how much of the

generator's output capacity is being used and how much power

remains available. The display also indicates the time since last

user reset and the total accumulated runtime of the generator.

Power Bar - This bargraph provides a quick visual indication of

the percentage of rated output currently being supplied.

% Load Indicator - This is a numeric version of the Power Bar.

Hour Meter - This indicates the total number of hours the

generator has run since manufacture.

Maintenance Timer - This indicates the number of hours the

generator has run since the last user reset. This timer should

be reset after every oil change or any other maintenance task.

Follow the instructions in the engine owners manual for proper

engine maintenance intervals.

Reset Button - Pressing and holding this button will reset the

Maintenance Timer to 0 HRS.

English

CONTROL PANEL

MAJOR GENERATOR FEATURES

TOOLS REQUIRED: 1/2” and 9/16" sockets and ratchets,

block(s) of wood (minimum of 6” tall). Refer to the parts list

on page 9.

WHEEL INSTALLATION

1.Block up end of generator opposite the fuel tank cap to

install wheel kit.

2.Insert wheel spacer (item 39) into the center of the wheel

(item 28).

3.Slide 3/8 x 4.25” bolt (item 32) and 3/8 washer (item 27)

through the wheel (item 28), then through the wheel

bracket on the carrier, with the offset side of the wheel hub

against the wheel bracket.

4.Thread 3/8 nyloc nut (item 33) onto the bolt and tighten to

securely clamp the wheel assembly to the carrier.

5.Repeat above instructions for the remaining wheel.

FOOT INSTALLATION

1.Blocking up the engine side of the generator, place the foot

bracket (item 43) under the carrier channel. Thread a

5/16-18 x 4” bolt (item 42) with a rubber foot (item 29)

through the mounting holes and thread a 5/16 flange nut

(item 47) to the bolt to secure the foot bracket to the carrier.

Caution: Do not over tighten so that the rubber foot

material collapses.

LOCKING HANDLE

1.Attach the lanyards (item 30) to the release pins (item 34)

and carrier as shown in the illustration.

2. To lock the handle (item 25) in the extended position, align

the holes in the handle brackets with the holes in the carrier

brackets and insert the release pins (item 34).

Warranty Coverage: Powermate Corporation (the Company)

warrants to the original retail customer in North America that it

will repair or replace, free of charge, any parts found by the

Company or its authorized service representative to be

defective in material or workmanship. This warranty covers the

cost of replacement parts and labor for defects in material or

workmanship.

Not Covered:

· Transportation charges for sending the product to the

Company or its authorized service representative for

warranty service, or for shipping repaired or replacement

products back to the customer; these charges must be

borne by the customer.

· Damages caused by abuse or accident, and the effects of

corrosion, erosion and normal wear and tear.

· Warranty is voided if the customer fails to install, maintain

and operate the product in accordance with the instructions

and recommendations of the Company set forth in the

owner's manual.

The Company will not pay for repairs or adjustments to the

product, or for any costs or labor, performed without the

Company's prior authorization.

Warranty Period: Two (2) years from the date of purchase on

products used solely for consumer applications; if a product is

used for business or commercial applications, the warranty

period will be limited to one (1) year from the date of purchase;

if a product is used for rental applications, the warranty period

will be limited to ninety (90) days from the date of purchase.

For warranty service, the customer must provide dated proof of

purchase and must notify the Company within the warranty

period.

For warranty service: Call toll free 800-445-1805, or write

to Powermate Corporation, Product Services, 4970 Airport

Road, P. O. Box 6001, Kearney, NE 68848.

EXCLUSIONS AND LIMITATIONS: THE COMPANY MAKES

NO OTHER WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED. IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY AND OF FITNESS

FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED. THE WARRANTY SERVICE DESCRIBED

ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS

WARRANTY; LIABILITY FOR INCIDENTAL AND

CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE

EXTENT PERMITTED BY LAW.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state. Some states

do not allow a disclaimer of implied warranties, or the exclusion

or limitation of incidental and consequential damages, so the

above disclaimers and exclusions may not apply to you.

English

PORTABILITY KIT INSTALLATION

LIMITED WARRANTY

Page is loading ...

REF.PARTDESCRIPTION DESCRIPTION DESCRIPCIÓNQTY

NO.NO.

10063806Carrier, assemblyEnsemble transportTransportador, conjunto1

2Note AEngine 12 hp Yamaha OHVMoteurMotor1

30051094IsolatorSectionneurAislador4

40064107Module, low oilModule, bas niveau d'huileMódulo, nivel bajo de aceite1

50057512Bolt whz 3/8-18 x 1 1/4BoulonPerno4

60062797Connector, panelConnecteur, tableauConector, panel 1

70063935Bolt, hex 5/16-24 x 9.50BoulonPerno1

8Note BWasher, lock 5/16Contre-écrou 5/16Arandela, de cierre 5/1610

90008854Lug, groundOeillet de mise à la terreTerminal, tierra1

100040832Nut, nyloc 1/4-20Écrous nyloc 1/4-20 Tuerca, nyloc 1/4-20 8

11Note BBolt, 5/16-18 x 1 1/2BoulonPerno2

12Note BWasher, flat 5/16Rondelle plates 5/16Arandela, plana 5/165

130048736Nut, nyloc 5/16-18Écrous nyloc 5/16-18Tuerca, nyloc 5/16-182

140049224Assembly, ground wireEnsemble fil de masse tressé a tierraConjunto, cable trenzado 1

15Note BWasher, star external 5/16Rondelle à dents externa 5/16Arandela, estrella 2

16Note BBolt, hex 5/16-18 x 3/4Boulon, tête hex 5/16-18 x 3/4Perno1

0063822MufflerSilencieuxSilenciador1

180063701GasketJointEmpaquetadura1

0064237Panel, wiredTableau complet câbléPanel, cabeado completo1

19A0049071Circuit Breaker 20 ampDisjoncteurs 20 ampCortacircuitos 20 amp2

19B0062199Circuit Breaker 25 amp dualDisjoncteurs 25 ampCortacircuitos 25 amp1

200063830Bracket, low oilSupport, bas niveau d'huileSoporte, nivel bajo de aceite1

210064084

Shield, heatÉcran de chaleurPantalla para el calor1

22Note CFuel tank assemblyEnsemble complet du réservoirConjunto tanque1

22A0061817Fuel Gauge/ScrewsCombustible Indicador/TornillosEssence Écartement/Visser1

22B0061942Strainer BasketPassoire PanierColador Canasta1

22C0061816Fuel CapCapuchonTapa de combustible1

230061811Fuel Shut OffFermeture d’essenceApagado combustible1

23A0061876Filter, fuel valve and washerFiltre et rondellesFiltro y arandela1

23B0061875Nut, fuel valveÉcrous Tuerca1

24Note BBolt, 1/4-20 x 3/4BoulonPerno3

250064178HandlePoignéeManija2

26Note BBolt, 5/16-18 x 2 1/4BoulonPerno2

27Note BWasher, flat 3/8Rondelle plates 3/8Arandela, plana 3/82

280057704WheelRoueRueda2

290055894Rubber FootPiedPie2

300062174LanyardLanyardAcollador2

310058933Washer, flat 1/4 WRondelle plates 1/4 largeArandela, plana 1/4 lejos1

32Note BBolt, 3/8-16 x 4.25BoulonPerno2

330057578Nut, nyloc 3/8-16Écrous nyloc 3/8-16Tuerca, nyloc 3/8-162

340062502Pin, releaseEpingle de relâchementAlfileres de la liberación2

350058955Cap, plasticCapuchonTapa2

36Note BWasher, flat 1/4Rondelle plates 1/4Arandela, plana 1/46

370064108Nut whz 8mmÉcrousTuerca2

380050298Switch, RockerInterrupteurInterruptor1

390062433Wheel spacerBague d’espacement Espaciador de la rueda2

400062495Grip, handlePoignéeEmpuñadura2

42Note BBolt, 5/16-18 x 4BoulonPerno2

430063212Bracket, footSupport de piedSoporte del pie1

440049268Bolt, M8 x 16mmBoulonPerno3

45Note BBolt, 1/4-20 x 1 1/4BoulonPerno1

46Note BBolt, 1/4-20 x 1BoulonPerno4

470057254Nut, hex flg 5/16-18Écrous 5/16-18Tuerca 5/16-187

48Note BBolt, 5/16-18 x 1 1/4BoulonPerno2

49Note BWasher, star external 1/4Rondelle à dents externa 1/4Arandela, estrella 2

500064138Screw #10 x .75VisTornillo2

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

RefPartDescription Description DescripciónQty

No.No.

510063821Generator head, SumecTête de la génératrice, SumecCabezal del generador, Sumec1

51A0063300Adapter, engineAdaptateur pour moteurAdaptor, motor1

51B0063940RotorRotorRotor1

51C0063941StatorStatorEstator1

51D0063942Band, stator coverBandeBanda1

51E0063943Bolt, M6 x 195BoulonPerno4

51F0063229Support, bearingSupport, roulementSoporte, Cojinete1

51G0063230Brush moduleBrosser le moduleCepille módulo1

51H0063231Screw flg M5 x 16mmVisTornillo8

51I0063948AVR moduleLa tension automatique régulatriceEl regulador automático del voltaje1

51J0063944Bolt, M5 x 230BoulonPerno2

51K0063235Nut, nyloc M5 Écrous nyloc Tuerca nyloc2

51L0063236Terminal blockBloc délimitantBloque terminal1

51M0063237Washer M5RondelleArandela8

51N0063238Washer, lock M5Contre-écrouArandela, de cierre10

51O0063239Nut M5ÉcrousTuerca8

51P0063240Cover, endCouvercleTapa1

51Q0063241Screw flg M5 x 8mmVisTornillo2

51R0063225FanVentilateurVentilador1

51S0063364Screw M5 x 20mmVisTornillo4

51T0063365BearingRoulementCojinete1

51U0063932Stator harnessHarnais de statorArreos de estator1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

Note A:

Powermate Corporation

will not provide engines as replacement parts. Engines are covered through the engine manufacturer's warranty. Consult the accompanying

engine manual or contact our service department for assistance.

Note B:

These are standard parts available at your local hardware store.

Note C:

Contact your nearest Coleman® Powermate® Service Center for replacement fuel tanks.

WARNING: To avoid possible personal injury or equipment damage, a registered electrician or an authorized service representative should

perform installation and all service. Under no circumstances should an unqualified person attempt to wire into a utility circuit.

Remarque A:

Powermate Corporation

ne fournit pas de moteurs dans ses pièces détachées. Les moteurs sont couverts par la garantie du fabricant de moteurs. Consulter le

manuel du moteur inclus ou contacter notre département de service après-vente pour toute assistance.

Remarque B:

Ces pièces sont des pièces standard disponibles en quincaillerie.

Remarque C:

Pour commander un réservoir de rechange, contacter Centre de service Coleman® Powermate® le plus proche.

AVERTISSEMENT: Pour éviter toute blessure personnelle ou dommage à l’équipement, l’installation et tout entretien devralent être effectués par un

électricien qualifié ou un préposé au service autorisé. En aucun cas, une personne non-qualifiée ne devrait essayer de faire le raccord au circuit principal.

Nota A:

Powermate Corporation

no proporcionará los motores como repuestos. Los motores están cubiertos por medio de la garantía del fabricante del motor. Consulte el

manual adjunto del motor o comuníquese con nuestro departamento de servicio para recibir ayuda al respecto.

Nota B:

Estas son piezas estándar disponibles en su ferretería local.

Nota C:

Para hacer pedidos de tanques, localice el Centro de Servicio de Coleman® Powermate®más cercano.

ADVERTENCIA: Para evitar posibles lesiones físcas o daños materiales, es necesario que la instalación y todo el servicio sea realizado por un electricista

matriculado o representatnte de servicio autorizado. Bajo ninguna circunstancia debe permitirse que una persona que no está capacitad trate de

manipular cables dentro del circuito de servicio eléctrico.

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and Powermate Corporation (herein "Powermate") are pleased to explain the evaporative emission

control system (EECS) warranty on your 2006 generator. In California, new generators must be designed, built and equipped to meet the

State's stringent anti-smog standards. Powermate must warrant the EECS on your generator for the periods of time listed below, provided

there has been no abuse, neglect or improper maintenance of your generator.

Your EECS includes parts such as: fuel hoses.

MANUFACTURER'S WARRANTY COVERAGE:

This evaporative emission control system is warranted for two years. The warranty period begins on the date the generator is delivered to

an ultimate purchaser.

Powermate warrants to the ultimate purchaser and any subsequent owner that the generator is (i) designed, built and equipped so as to

conform with all applicable regulations; and (ii) free from defects in materials and workmanship that cause the failure of a warranted part

to be identical in all material respects to that part as described in Powermate's application for certification.

If any evaporative emission-related part on your generator is defective, the part will be repaired or replaced by Powermate.

OWNER'S WARRANTY RESPONSIBILITIES:

As the generator owner, you are responsible for performance of the required maintenance listed in your owner's manual. Powermate

recommends that you retain all receipts covering maintenance on your generator, but Powermate cannot deny warranty solely for the lack

of receipts. You should, however, be aware that Powermate may deny you warranty coverage if your generator or a part has failed due to

abuse, neglect or improper maintenance or unapproved modifications.

You are responsible for presenting your generator to an authorized Powermate warranty service center as soon as the problem exists. The

warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your

warranty coverage, you should call Powermate Product Service at 1-800-445-1805.

DETAILS OF YOUR WARRANTY

Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:

(1)Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted

for the period stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by

Powermate according to Subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the

remainder of the period.

(2)Any warranted part that is scheduled only for regular inspection in the written instructions supplied, is warranted for the warranty

period stated above. Any such part repaired or replaced under warranty will be warranted for the remaining warranty period.

(3)Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied, is warranted for

the period of time before the first scheduled replacement date for that part. If the part fails before the first scheduled replacement

date, the part will be repaired or replaced by Powermate according to Subsection (4) below. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first scheduled replacement date for the part.

(4)Repair or replacement of any warranted part under the warranty provisions herein must be performed at an authorized Powermate

warranty service center at no charge to the owner.

(5)The generator owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective,

emission-related warranted part, provided that such diagnostic work is performed at an authorized Powermate warranty service

center.

(6)Powermate is liable for damages to other engine or generator components proximately caused by a failure under warranty of any

warranted part.

(7)Throughout the generator warranty period stated above, Powermate will maintain a supply of warranted parts sufficient to meet the

expected demand for such parts.

(8)Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge

to the owner. Such use will not reduce the warranty obligations of Powermate.

(9)Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on

or modified parts by the ultimate purchaser will be grounds for disallowing a warranty claims. Powermate will not be liable to war

rant failures or warranted parts caused by the use of a non-exempted add-on or modified part.

(10)The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty

coverage if the generator has been abused, neglected or improperly maintained, and such abuse, neglect or improper maintenance

was the direct cause of the need for repair or replacement of the part.

WARRANTED PARTS:

The following emission warranty parts list is covered:

Fuel Hose.

English

The California Air Resources Board and Yamaha Motor

Corporation, U.S.A. are pleased to explain the emission

control system warranty on your 1995 or later utility

equipment engine. In California, new utility and lawn and

garden engines must be designed, built and equipped to

meet the State's stringent anti-smog standards. Yamaha

must warrant the emission control system on your utility

equipment engine for the periods of time listed below

provided there has been no abuse, neglect or improper

maintenance of your utility equipment engine.

Your emission control system may include parts such as

the carburetor or fuel-injection system, the ignition

system, and catalytic converter. Also included may be

hoses, belts, connectors and other emission-related

assemblies.

Where a warrantable condition exists, Yamaha will repair

your utility equipment engine at no cost to you including

diagnosis, parts and labor.

MANUFACTURER'S WARRANTY COVERAGE

The 1995 and later utility engines are warranted for two

years. If any emissions-related part on your engine is

defective, the part will be repaired or replaced by Yamaha.

OWNER'S WARRANTY RESPONSIBILITIES

• As the utility equipment engine owner, you are

responsible for the performance of the required

maintenance listed in your owner's manual. Yamaha

recommends that you retain all receipts covering

maintenance on your utility equipment engine, but

Yamaha cannot deny warranty solely for the lack of

receipts or for your failure to ensure the performance of all

scheduled maintenance.

• As the utility equipment engine owner, you should

also be aware that Yamaha may deny you warranty

coverage if your utility equipment engine or a part has

failed due to abuse, neglect, improper maintenance or

unapproved modifications.

•You are responsible for presenting you utility

equipment engine to a Yamaha dealer as soon as a

problem exists. The warranty repairs should be

completed in a reasonable time, not to exceed 30 days.

If you have any questions regarding your warranty rights

and responsibilities, you should contact the Yamaha

Customer Relations Department at 1-800-962-7926.

Yamaha Motor Corporation, U.S.A. warrants to the

ultimate purchaser and each subsequent purchaser

thereafter that each new 1995 and later model year utility

engine certified for sale and registered in California are:

1.Designed, built, and equipped so as to conform, at

the time of sale, with all applicable regulations

adopted by the California Air Resources Board, and

2.All warranted parts are free from defects in material

and workmanship for the warranty period of the utility

engine or the period prior to the first scheduled

replacement point of the warranted part as required

by the maintenance schedule, if applicable,

whichever is less. A defect exists when a deficiency

in material or workmanship is such that an

emission-related warranted part does not function as

designed.

The warranty period begins on the date that the utility

equipment engine is delivered to an ultimate purchaser or

on the date it is first placed in service.

WARRANTED PARTS INCLUDE the following:

1.Fuel Metering System

Carburetor and internal parts (or fuel injection)

Air/fuel ratio feedback and control system

2.Air Induction system

Controlled hot air intake system

Intake manifold

3. Ignition System

Spark plugs*

Magneto or electronic ignition system

Spark advance/retard system

4.Exhaust Gas Recirculation (EGR) System

EGR valve body, and carburetor spacer if applicable

EGR rate feedback and control system

5.Air Injection System

Air pump or pulse valve

Valves affecting distribution of flow

Distribution manifold

6.Catalyst or Thermal Reactor System

Catalytic converter

Thermal reactor

Exhaust manifold

7.Particulate Controls

Traps, filters, precipitators, and any other device used

to capture particulate emissions

YAMAHA MOTOR CORPORATION, U.S.A.

UTILITY EQUIPMENT ENGINES

CALIFORNIA EMISSION CONTROL WARRANTY

YOUR WARRANTY RIGHTS AND OBLIGATIONS

Effective Date 1/1/95 Continued

English

8.Miscellaneous Items Used in Above Systems

Vacuum, temperature, and time sensitive valves and

switches

Electronic controls

Hoses, belts, connectors, and assemblies

9.Engine components damaged due to a failure under

warranty of a warranted part

*The original spark plug(s) are warranted for the period of

replacement indicated in the Owner's Manual and not the

useful life of the utility equipment engine (see your

Owner's Manual).

DURING THE PERIOD OF THIS WARRANTY

Yamaha Motor Corporation, U.S.A. will repair or replace

any warranted part deemed defective by Yamaha during

the scope of the warranty without charge to the owner,

including parts, labor, and diagnosis. This work must be

done at an authorized Yamaha dealer. Give notice to an

authorized Yamaha dealer of any apparent defect(s)

within a reasonable period of time after discovery. The

utility equipment engine must be made available for

inspection by an authorized Yamaha dealer.

OWNER'S RESPONSIBILITY: The owner of the utility

equipment engine is responsible for the performance of

required maintenance (see you Owner's Manual).

Receipts and maintenance records covering the

performance of regular maintenance should be retained in

the event questions arise concerning maintenance. The

receipts should be transferred to each subsequent owner

of this utility equipment engine.

The emission control systems of your Yamaha utility

equipment engine were designed, built, tested, and

certified as being in conformity with California emission

control regulations using genuine Yamaha parts.

Accordingly, it is recommended that any replacement

part(s) used for maintenance, replacement, or repair of

emission control systems be Yamaha parts. The owner

may elect to have maintenance, replacement, or repair of

the emission control devices and systems performed by

any repair establishment or individual, and may elect to

use parts other than Yamaha parts for such maintenance,

replacement, or repair without invalidating this warranty.

However, the cost of such service or parts will not be

covered under the warranty.

EXCLUSIONS: No warranty coverage will be allowed if

the part(s) failure was caused by owner/operator abuse,

neglect, tampering, improper adjustment unless

performed by a dealer during warranty repair work,

modification, misuse, alteration, or improper maintenance

(see your Owner's Manual).

Use of parts which are not qualitatively equivalent to

genuine Yamaha parts, improper service, or lack of

required maintenance which causes failure or a warranted

part may constitute abuse and/or improper service,

thereby invalidating warranty liability hereunder.

This warranty does not cover damage resulting from

accidents, acts of nature, or other events or occurrences

beyond the control of Yamaha. Yamaha Motor

Corporation, U.S.A. expressly disclaims responsibility for

any and all consequential damages, such as loss of time,

inconvenience, loss of use of the utility equipment engine,

or commercial loss.

YAMAHA MOTOR CORPORATION, U.S.A.

Post Office Box 6555

Cypress, California 90630

Page is loading ...

are registered trademarks of The Coleman Company, Inc. used under license.

Powermate ® is a registered trademark of Powermate Corporation.

sont des marques déposées de The Coleman Company, Inc. utilisées sous licence.

Powermate® est une marque déposée de Powermate Corporation.

son marcas comerciales registradas de The Coleman Company, Inc. utilizadas bajo licencia.

Powermate ® es una marca comercial registrada de Powermate Corporation.

Coleman® and

Coleman® et

Coleman® y

4970 Airport Road

P. O. Box 6001

Kearney, NE 68848

1-800-445-1805

1-308-237-2181

Fax 1-308-234-4187

Powermate PMC606750 User manual

Brand: Powermate

Model: PMC606750

Category: Power generators

Type: User manual

Download PDF

report

in other languages

français: Powermate PMC606750 Manuel utilisateur
español: Powermate PMC606750 Manual de usuario

Powermate PMC606750 User manual

Powermate PMC606750 User manual

in other languages

Related papers

Other documents