Powermate PM0606750 User manual

Page is loading ...

*12 HP Yamaha OHV engine

*Cast-iron cylinder sleeve

*Low oil sensor

*Receptacles on control panel

*DIGITECH™ Digital Information Center

*7 gallon metal fuel tank

*Portability Kit

A.120 Volt GFCI Receptacle

Ground Fault Circuit Interrupter duplex receptacle is rated

so that a total of 20 amps may be drawn regardless of whether

both halves or just one receptacle is used. This receptacle may

be used along with other receptacles provided the generator is

not overloaded and total power drawn is kept within nameplate

ratings.

Ground Fault Circuit Interrupter

(Conforms to U.L 943, Class A and NEC requirements)

This device protects you against hazardous electrical shock

that may be caused if your body becomes a path through which

electricity travels to reach ground. This could happen when

you touch an appliance or cord that is “ live “ through faulty

mechanism, damp or worn insulation, etc.

B.120/240 V, 30 Ampere Twistlock Receptacle

A maximum of 30 amps may be drawn from the 120/240

volt receptacle, provided it is the only receptacle used.

However, current must be limited to the nameplate rating. If the

120/240 volt receptacle is used along with the 120 volt

receptacle, the total load drawn must not exceed the nameplate

ratings.

C.Circuit Breakers

The receptacles are protected by an AC circuit breaker. If

the generator is overloaded or an external short circuit occurs,

the circuit breaker will trip. If this occurs, disconnect all

electrical loads and try to determine the cause of the problem

before attempting to use the generator again. If overloading

causes the circuit breaker to trip, reduce the load. NOTE:

Continuous tripping of the circuit breaker may cause

damage to generator or equipment. The circuit breaker may

be reset by pushing the button of the breaker.

D.Engine On/Off Switch

E.DIGITECH™ Digital Information Center

The DIGITECH™ Digital Information Center is a patented

feature available only on select Coleman® Powermate® Brand

generators.

At a glance, the user can instantly see how much of the

generator's output capacity is being used and how much power

remains available. The display also indicates the time since last

user reset and the total accumulated runtime of the generator.

Power Bar - This bargraph provides a quick visual indication of

the percentage of rated output currently being supplied.

% Load Indicator - This is a numeric version of the Power Bar.

Total Timer - This indicates the total number of hours the

generator has run since manufacture.

Maintenance Timer - This indicates the number of hours the

generator has run since the last user reset. This timer should

be reset after every oil change or any other maintenance task.

Follow the instructions in the engine owners manual for proper

engine maintenance intervals.

Reset Button - Pressing and holding this button will reset the

Maintenance Timer to 0 HRS.

English

CONTROL PANEL

MAJOR GENERATOR FEATURES

TOOLS REQUIRED: 1/2” and 9/16" sockets and ratchets,

block(s) of wood (minimum of 6” tall). Refer to the parts list

on page 9.

WHEEL INSTALLATION

1.Block up end of generator opposite the fuel tank cap to

install wheel kit.

2.Insert wheel spacer (item 39) into the center of the wheel

(item 28).

3.Slide 3/8 x 4.25” bolt (item 32) and 3/8 washer (item 27)

through the wheel (item 28), then through the wheel

bracket on the carrier, with the offset side of the wheel hub

against the wheel bracket.

4.Thread 3/8 nyloc nut (item 33) onto the bolt and tighten to

securely clamp the wheel assembly to the carrier.

5.Repeat above instructions for the remaining wheel.

FOOT INSTALLATION

1.Blocking up the engine side of the generator, place the foot

bracket (item 43) under the carrier channel. Thread a

5/16-18 x 4” bolt (item 42) with a rubber foot (item 29)

through the mounting holes and thread a 5/16 flange nut

(item 47) to the bolt to secure the foot bracket to the carrier.

Caution: Do not over tighten so that the rubber foot

material collapses.

LOCKING HANDLE

1.Attach the lanyards (item 30) to the release pins (item 34)

and carrier as shown in the illustration.

2. To lock the handle (item 25) in the extended position, align

the holes in the handle brackets with the holes in the carrier

brackets and insert the release pins (item 34).

Warranty Coverage: Powermate Corporation (the Company)

warrants to the original retail customer in North America that it

will repair or replace, free of charge, any parts found by the

Company or its authorized service representative to be

defective in material or workmanship. This warranty covers the

cost of replacement parts and labor for defects in material or

workmanship.

Not Covered:

· Transportation charges for sending the product to the

Company or its authorized service representative for

warranty service, or for shipping repaired or replacement

products back to the customer; these charges must be

borne by the customer.

Engine is covered exclusively by a separate warranty from

the engine manufacturer, included with the engine Manual.

· Damages caused by abuse or accident, and the effects of

corrosion, erosion and normal wear and tear.

· Warranty is voided if the customer fails to install, maintain

and operate the product in accordance with the instructions

and recommendations of the Company set forth in the

owner's manual.

The Company will not pay for repairs or adjustments to the

product, or for any costs or labor, performed without the

Company's prior authorization.

Warranty Period: Two (2) years from the date of purchase on

products used solely for consumer applications; if a product is

used for business or commercial applications, the warranty

period will be limited to one (1) year from the date of purchase;

if a product is used for rental applications, the warranty period

will be limited to ninety (90) days from the date of purchase.

For warranty service, the customer must provide dated proof of

purchase and must notify the Company within the warranty

period.

For warranty service: Call toll free 800-445-1805, or write

to Powermate Corporation, Product Services, 4970 Airport

Road, P. O. Box 6001, Kearney, NE 68848.

EXCLUSIONS AND LIMITATIONS: THE COMPANY MAKES

NO OTHER WARRANTY OF ANY KIND, EXPRESS OR

IMPLIED. IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY AND OF FITNESS

FOR A PARTICULAR PURPOSE, ARE HEREBY

DISCLAIMED. THE WARRANTY SERVICE DESCRIBED

ABOVE IS THE EXCLUSIVE REMEDY UNDER THIS

WARRANTY; LIABILITY FOR INCIDENTAL AND

CONSEQUENTIAL DAMAGES IS EXCLUDED TO THE

EXTENT PERMITTED BY LAW.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state. Some states

do not allow a disclaimer of implied warranties, or the exclusion

or limitation of incidental and consequential damages, so the

above disclaimers and exclusions may not apply to you.

English

PORTABILITY KIT INSTALLATION

LIMITED WARRANTY

Page is loading ...

REF.PARTDESCRIPTION DESCRIPTION DESCRIPCIÓNQTY

NO.NO.

10063806Carrier, assemblyEnsemble transportTransportador, conjunto1

2Note AEngine 12 hp Yamaha OHVMoteurMotor1

30051094IsolatorSectionneurAislador4

40064107Module, low oilModule, bas niveau d'huileMódulo, nivel bajo de aceite1

50057512Bolt whz 3/8-18 x 1 1/4BoulonPerno4

60062797Connector, panelConnecteur, tableauConector, panel 1

70063935Bolt, hex 5/16-24 x 9.50BoulonPerno1

8Note BWasher, lock 5/16Contre-écrou 5/16Arandela, de cierre 5/168

90008854Lug, groundOeillet de mise à la terreTerminal, tierra1

100040832Nut, nyloc 1/4-20Écrous nyloc 1/4-20 Tuerca, nyloc 1/4-20 8

11Note BBolt, 5/16-18 x 1 1/2BoulonPerno2

12Note BWasher, flat 5/16Rondelle plates 5/16Arandela, plana 5/165

130048736Nut, nyloc 5/16-18Écrous nyloc 5/16-18Tuerca, nyloc 5/16-182

140049224Assembly, ground wireEnsemble fil de masse tressé a tierraConjunto, cable trenzado 1

15Note BWasher, star external 5/16Rondelle à dents externa 5/16Arandela, estrella 2

16Note BBolt, hex 5/16-18 x 3/4Boulon, tête hex 5/16-18 x 3/4Perno1

0063822MufflerSilencieuxSilenciador1

180063701GasketJointEmpaquetadura1

0063811Panel, wiredTableau complet câbléPanel, cabeado completo1

19A0049071Circuit Breaker 20 ampDisjoncteurs 20 ampCortacircuitos 20 amp2

19B0049382Circuit Breaker 30 ampDisjoncteurs 30 ampCortacircuitos 30 amp2

200063830Bracket, low oilSupport, bas niveau d'huileSoporte, nivel bajo de aceite1

210064084

Shield, heatÉcran de chaleurPantalla para el calor1

22Note CFuel tank assemblyEnsemble complet du réservoirConjunto tanque1

22A0061817Fuel Gauge/ScrewsCombustible Indicador/TornillosEssence Écartement/Visser1

22B0061942Strainer BasketPassoire PanierColador Canasta1

22C0061816Fuel CapCapuchonTapa de combustible1

230061811Fuel Shut OffFermeture d’essenceApagado combustible1

23A0061876Filter, fuel valve and washerFiltre et rondellesFiltro y arandela1

23B0061875Nut, fuel valveÉcrous Tuerca1

24Note BBolt, 1/4-20 x 3/4BoulonPerno5

250064178HandlePoignéeManija2

26Note BBolt, 5/16-18 x 2 1/4BoulonPerno2

27Note BWasher, flat 3/8Rondelle plates 3/8Arandela, plana 3/82

280057704WheelRoueRueda2

290055894Rubber FootPiedPie2

300062174LanyardLanyardAcollador2

310058933Washer, flat 1/4 WRondelle plates 1/4 largeArandela, plana 1/4 lejos1

32Note BBolt, 3/8-16 x 4.25BoulonPerno2

330057578Nut, nyloc 3/8-16Écrous nyloc 3/8-16Tuerca, nyloc 3/8-162

340062502Pin, releaseEpingle de relâchementAlfileres de la liberación2

350058955Cap, plasticCapuchonTapa2

36Note BWasher, flat 1/4Rondelle plates 1/4Arandela, plana 1/46

370064108Nut whz 8mmÉcrousTuerca2

380050298Switch, RockerInterrupteurInterruptor1

390062433Wheel spacerBague d’espacement Espaciador de la rueda2

400062495Grip, handlePoignéeEmpuñadura2

42Note BBolt, 5/16-18 x 4BoulonPerno2

430063212Bracket, footSupport de piedSoporte del pie1

440049268Bolt, M8 x 16mmBoulonPerno3

45Note BBolt, 1/4-20 x 1 1/4BoulonPerno1

46Note BBolt, 1/4-20 x 1BoulonPerno2

470057254Nut, hex flg 5/16-18Écrous 5/16-18Tuerca 5/16-187

48Note BBolt, 5/16-18 x 1 1/4BoulonPerno2

49Note BWasher, star external 1/4Rondelle à dents externa 1/4Arandela, estrella 2

500064138Screw #10 x .75VisTornillo2

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

RefPartDescription Description DescripciónQty

No.No.

510063821Generator head, SumecTête de la génératrice, SumecCabezal del generador, Sumec1

51A0063300Adapter, engineAdaptateur pour moteurAdaptor, motor1

51B0063940RotorRotorRotor1

51C0063941StatorStatorEstator1

51D0063942Band, stator coverBandeBanda1

51E0063943Bolt, M6 x 195BoulonPerno4

51F0063229Support, bearingSupport, roulementSoporte, Cojinete1

51G0063230Brush moduleBrosser le moduleCepille módulo1

51H0063231Screw flg M5 x 16mmVisTornillo8

51I0063948AVR moduleLa tension automatique régulatriceEl regulador automático del voltaje1

51J0063944Bolt, M5 x 230BoulonPerno2

51K0063235Nut, nyloc M5 Écrous nyloc Tuerca nyloc2

51L0063236Terminal blockBloc délimitantBloque terminal1

51M0063237Washer M5RondelleArandela8

51N0063238Washer, lock M5Contre-écrouArandela, de cierre10

51O0063239Nut M5ÉcrousTuerca8

51P0063240Cover, endCouvercleTapa1

51Q0063241Screw flg M5 x 8mmVisTornillo2

51R0063225FanVentilateurVentilador1

51S0063364Screw M5 x 20mmVisTornillo4

51T0063365BearingRoulementCojinete1

51U0063932Stator harnessHarnais de statorArreos de estator1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

Note A:

Powermate Corporation

will not provide engines as replacement parts. Engines are covered through the engine manufacturer's warranty. Consult the accompanying

engine manual or contact our service department for assistance.

Note B:

These are standard parts available at your local hardware store.

Note C:

Contact your nearest Coleman® Powermate® Service Center for replacement fuel tanks.

WARNING: To avoid possible personal injury or equipment damage, a registered electrician or an authorized service representative should

perform installation and all service. Under no circumstances should an unqualified person attempt to wire into a utility circuit.

Remarque A:

Powermate Corporation

ne fournit pas de moteurs dans ses pièces détachées. Les moteurs sont couverts par la garantie du fabricant de moteurs. Consulter le

manuel du moteur inclus ou contacter notre département de service après-vente pour toute assistance.

Remarque B:

Ces pièces sont des pièces standard disponibles en quincaillerie.

Remarque C:

Pour commander un réservoir de rechange, contacter Centre de service Coleman® Powermate® le plus proche.

AVERTISSEMENT: Pour éviter toute blessure personnelle ou dommage à l’équipement, l’installation et tout entretien devralent être effectués par un

électricien qualifié ou un préposé au service autorisé. En aucun cas, une personne non-qualifiée ne devrait essayer de faire le raccord au circuit principal.

Nota A:

Powermate Corporation

no proporcionará los motores como repuestos. Los motores están cubiertos por medio de la garantía del fabricante del motor. Consulte el

manual adjunto del motor o comuníquese con nuestro departamento de servicio para recibir ayuda al respecto.

Nota B:

Estas son piezas estándar disponibles en su ferretería local.

Nota C:

Para hacer pedidos de tanques, localice el Centro de Servicio de Coleman® Powermate®más cercano.

ADVERTENCIA: Para evitar posibles lesiones físcas o daños materiales, es necesario que la instalación y todo el servicio sea realizado por un electricista