Rugged Ridge 11546.20 Installation guide

Brand
Rugged Ridge
Model
11546.20
Type
Installation guide

Rugged Ridge 11546.20 is a heavy-duty rear bumper designed for Jeep® JK Wranglers. Constructed from durable materials, it provides enhanced protection for your vehicle during off-road adventures. The bumper features integrated D-rings for convenient recovery points, allowing you to confidently navigate challenging terrains. Additionally, the 11546.20 includes mounting provisions for a tire carrier, expanding its versatility for carrying additional gear.

Rugged Ridge 11546.20 is a heavy-duty rear bumper designed for Jeep® JK Wranglers. Constructed from durable materials, it provides enhanced protection for your vehicle during off-road adventures. The bumper features integrated D-rings for convenient recovery points, allowing you to confidently navigate challenging terrains. Additionally, the 11546.20 includes mounting provisions for a tire carrier, expanding its versatility for carrying additional gear.

11546.20
Jeep® JK Wrangler Rear HD Bumper
1. Remove original rear bumper. It is held in by 2 bolts on each side (Figure 1a), and 2 bolts that are
attached to brackets which fasten to the rear crossmember (Figure 1b). After the bumper is
removed, remove the small brackets from the rear crossmember (Figure 1c). Save the 4 bolts
from the side and the 2 bolts from the crossmember, as they are to be re-used.
Figure 1a Figure 1b Figure 1c
2. Place Bracket on rear frame rails. Brackets need to be angled up while slid over frame rail
(Figure 2a), and then dropped down to level once crossmember hook has been cleared. (Figure 2b).
Use bolts removed in Step 1 to bolt brackets to frame (Figure 2c). Two bolts are used to fasten
bracket to frame rail, and one to fasten bracket to rear crossmember. Do not tighten bolts yet.
Page 1 of 2
Figure 2a Figure 2b Figure 2c
Contents:
1. Rear HD Bumper (1)
2. Left Bracket (1)
3. Right Bracket (1)
4. D-Ring (2)
5. 12mm Washer (9)
6. 12mm Bolt (9)
7. Plugs (6)
8. Nut Plate (1)
1 2
3
7
4
5
6
8
4. Set Bumper onto Brackets. It may be necessary / helpful to open the door so that the spare tire
does not interfere with installation (Figure 3a). Install D-Rings using 12mm Bolts and Washers.
Do not tighten bolts yet.
Figure 4a
5. Tighten 8 bolts that hold D-Rings to the Bumper and Brackets (Figure 4a), then tighten 6 original
bolts that hold the brackets to the vehicle (Figure 4b). Finally, tighten bolt that was installed in Step 3.
Install caps in unused holes on top of bumper unless you are installing the 11546.22 Tire Carrier at
the same time (Figure 4c). Installation is now complete!
Page 2 of 2
Figure 5a
Figure 4b
Congratulations on the purchase and installation of a quality Rugged Ridge product!
Figure 5b Figure 5c
3. Insert Nut Plate into right frame rail as shown (Figure 3a). Hold in place while installing 12mm Bolt
and Washer through side of Right Bracket (Figure 3b). Do not tighten bolt yet.
© Copyright 2008, Omix-Ada
Omix-Ada Inc.
460 Horizon Dr. Suite 400
Suwanee, Georgia 30024
Figure 3a Figure 3b
  • Page 1 1
  • Page 2 2

Rugged Ridge 11546.20 Installation guide

Brand
Rugged Ridge
Model
11546.20
Type
Installation guide

Rugged Ridge 11546.20 is a heavy-duty rear bumper designed for Jeep® JK Wranglers. Constructed from durable materials, it provides enhanced protection for your vehicle during off-road adventures. The bumper features integrated D-rings for convenient recovery points, allowing you to confidently navigate challenging terrains. Additionally, the 11546.20 includes mounting provisions for a tire carrier, expanding its versatility for carrying additional gear.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents