Symmons S-26-STN Installation guide

Category
Faucets
Type
Installation guide
2.5 mm
cold water
Quick Install Guide Andora Kitchen Faucet, S-26-IPS
Step 5
Connect water
supply lines
1/2 - 14 NPT ttings
nished deck
front view
Step 1
Position deck plate
over mounting hole
Step 6
Flush supply lines
and check for leaks
Step 4
Attach counterweight
Step 2
Attach and center
faucet assembly
Step 3
Connect pull-out spout hose
(optional)
Spray
on / off
with copper supply tubing and IPS connections
Finish Options
-STN
Satin Nickel
-STS
Stainless Steel
-
Chrome (standard)
Model Number
S-26-IPS Kitchen faucet
with copper supply tubing and
IPS connections
Need Help?
Contact Symmons customer service
at (800) 796-6667, (781) 848-2250,
Mon - Fri 7:30 am - 7:00 pm EST
Please check Symmons website
for technical help, the latest product
information and warranty policy.
www.symmons.com/service
Tools & Materials
Kitchen Faucet S-26-IPS
Installation and Service Instructions
Andora
Discontinued ECO 12600
Step 1 Position deck plate over mounting hole
<OPTIONAL> Deck plate is typically used for covering existing
holes when faucet is being replaced. Install as required.
Step 2 Attach faucet assembly to deck
Step 3 Connect pull-out spout hose to supply
Step 4 Attach counterweight to hose
Caution: If replacing an older faucet ensure water
supply is turned OFF before removing and then turn
faucet handles ON to relieve water pressure.
1 2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
17 18 19 20
25 26
21 22 23 24
cold water
~ 28-30 inches
(710-762 mm)
nished deck
front view
1
2
3
cold water
cold water
front
nished deck
front view
Installation Instructions
Page 2
Step 5 Connect water supply lines
Step 6 Flush supply lines and check for leaks
Care of faucet finish
Clean nish area by using mild soap and water or non-
abrasive cleaner and then rinse immediately. A non-
abrasive wax may be used to preserve nish area.
Removing handle and cartridge
Replace collar and handle
Valve cartridge replacement
2.5 mm
1
2
cold water
HOT
COLD
Suggested method
Items listed below are shown
for reference only and not
included with this product.
1/2" IPS tting
3/8" ex hose
3/8" compression tting
1/2"-14 NPT
ttings included,
use as required
2.5 mm
Page 3
cold water
Finished deck
thickness
1-1/4" max
(32 mm)
center hole size
1-3/8" (35 mm) min
*
deck plate
10" (254 mm)
*
deck plate
2-7/16"
(62 mm)
*
deck plate 1/4"
(6 mm)
2-1/8" dia
(54 mm)
6-1/4"
(159 mm)
8-1/2"
(216 mm)
7-3/4"
(197 mm)
5"
(127 mm)
8" 1/8 (206 mm)
7-1/4"
(184 mm)
7-1/4"
(184 mm)
1/2" - 14 NPT ttings
*
Deck plate is optional;
typically used for covering
existing holes from 3-hole
faucet installations.
Dimensions Andora Kitchen Faucet S-26-IPS
with copper supply tubing and IPS connections
Note Dimensions subject to change without notice.
cold water
Replacement Part
Part Number Item
valve cartridgeKN-4
handle*
plug button*
screw
collar*
retainer
cartridge
KN-4
pull-out spout*
aerator
Faucet body*
o-ring
deck plate*
gasket
washer
metal washer
mounting nut
pull-out spout
hose
hot water inlet
counterweight
cold water inlet
put-out spout supply
washer
hose connector
Ordering replacement parts:
Symmons customer service: (800) 796-6667,
(781) 848-2250 M-F 7:30 am - 7:00 pm EST
Symmons distributors: www.symmons.com
*
Note: For decorative nish faucets add
appropriate letter sufx code to part
numbers marked with an asterisk (
*
).
IPS 1/2" compression ttings
optional, use as required
Parts Assembly Andora Kitchen Faucet, S-26-IPS
with copper supply tubing and IPS connections
Symmons Industries, Inc. 31 Brooks Drive Braintree, MA 02184 (800)796-6667, (781)848-2250 Fax: (800)961-9621,
(781)664-1300 ©2011 Symmons Industries www.symmons.com [email protected]
Printed in the USA Model S-26-IPS Part# KN-143 Document #ZV-370 RevDate 021512
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Symmons S-26-STN Installation guide

Category
Faucets
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI