GK1300 Series Electric Strike Installation Instructions
4” (116.9mm)
(41.5mm)
1
13/16”
(46.7mm)
1
3/8”
(35mm)
Specifications
• Heavy duty stainless steel construction (US 32D)
• Vertical adjustments allow for alignment with a wide
variety of mortise locks with offset latches
• Sliding keeper shim design for up to 1/8” (3mm) adjustment
for misaligned frames
• Accommodates deadbolts up to 1”
• Field selectable for fail-safe or fail-secure
• Non-handed design fits either right-handed or left-handed doors
• Trim plate included
• Optional latch monitor SW1300 (for GK1300M) - Indicates when door
is latched (The maximum input rating for SW1300M is 1.5A/40VDC)
• Includes 5 different stainless steel faceplates
Fail-Safe/ Fail-Secure Reversible
Fail-secure or fail-safe is field selectable by changing
position of screws as shown.
Features
Copyright Gianni Industries Inc All Rights Reserved
P-MU-GK1300 Published:2017.12.05
Note: Factory default setting is fail-secure.
FAIL-SAFE
FAIL-SECURE
Fail-Safe: Fail-Secure:
x
x
FAIL-SAFE
FAIL-SECURE
x
x
Sliding
Screw
Locking
Screw
Options
GK1300-12
GK1300-24
GK1300-1224
GK1300M-24
GK1300M-12
Part Number
GK1300M-1224
12 or 24 VDC 12/24 VDC
Latch Monitor
(SW1300)
1
3 3/8” (85mm)
3
5/16” (84.5mm)
1
5/8”
UL Requirements
• For indoor use only.
• Wiring methods shall be in accordance with NFPA 70.
• The GK1300 series is intended to be used with UL Listed Exit Hardware.
• The GK1300 series shall not impair the intended operation of an emergency exit.
• The GK1300 series shall not impair the operation of panic hardware mounted
on the door.
250,000 cycles (UL tested)
Operating Voltage
Current Draw
Operating Temp.
Endurance Rating
Latch Throw
Static Strength
Dynamic Strength
1,000,000 cycles (Factory tested)
12VDC, 24VDC, 12/24VDC
1” (25mm) max with 1/8” (3mm) door gap
1000 lbs (454Kg)
33 ft-lbs
Humidity
0~85% non-condensing
14°F to 120°F (-10°C to 49°C)
250mA/12VDC or 150mA/24VDC
300mA/12VDC, 150mA/24VDC
Single Voltage:
Dual Voltage:
1. Loosen and remove the locking screw.
2. Loosen and move the sliding screw to the desired setting,
and replace/retighten both screws.
+
+
+
--
}
Latch monitor wires
Rated:1.5A/40VDC
Power
Supply
Wiring Instructions
Brown: N.O.
White: COM.
Grey: N.C.
White: 12VDC Red: 24VDC
White: 12VDC Red: 24VDC
12 or 24 VDC Wiring Diagram
N.C. for “Fail-Safe” operation
N.O. for “Fail-Secure” operation
12/24 VDC Wiring Diagram
(Polarity Insensitive)
Red
Black
Control Device
(Polarity Insensitive)
White
Black
Control Device
For 12VDC Operation:
For 24VDC Opration:
Performance Level
Destructive Attack: Level I
Line Security: Level I
Standby Power: Level I
Endurance: Level IV
The mounting tabs are only used for aluminum and metal door frames. This is commonly done when retrofitting door frames.
Drill holes according to the template for installation
of the mounting tabs.
When installing, do not over-tighten the screws as
small adjustments may be required to secure a
snug fit for the door strike.
Mounting the Strike Using Mounting Tabs
Mounting the Trim Plate
1. If the hole cut for the faceplate
is too large or is jagged, the trim
plate can be mounted over the
hole to improve the appearance
of the installation.
2. Screw the trim plate into the
mounting holes at the top and
bottom of the door strike using
the included trim plate screws
before installing the strike to the
door frame.
Installing the Crimp Connectors
Mounting Tabs
Machine
Screws
1
1
/
4
"
(32mm)
1
1
/
16
" (27mm)
11
/
16
" (18mm)
3
1
/
8
" (79mm)
4
7
/
8
" (123.8mm
)
1
1
/
4
"
(32mm)
1
1
/
8
" (29mm)
7
/
8
" (22mm)
2
7
/
8
"
(73mm)
4
7
/
8
" (123.8mm
)
1
1
/
4
"
(32mm)
4
7
/
8
" (123.8mm
)
2
1
/
4
" (58mm) 1
1
/
18
" (28mm)
1
1
/
2
"
(38mm)
1
9
/
16
" (40mm)1
9
/
16
" (40mm)
1
3
/
4
"
(44mm)
1
1
/
4
"
(32mm)
4
7
/
8
" (123.8mm
)
11
/
16
" (18mm)
2
13
/
16
" (72mm)
1
1
/
4
"
(32mm)
4
7
/
8
" (123.8mm
)
1
5
/
16
"
(34mm)
GK1300 Series Faceplates Dimensions
Copyright Gianni Industries Inc All Rights Reserved
P-MU-GK1300 Published:2017.12.05
EF GHI
Note: If it is necessary to cut a hole in the frame, mounting tabs maybe required to strengthen the installation.
2
Deadbolt Latch Installation Latchbolt Installation
Crimp connectors are provided to make wiring connections
easier and more reliable. To install the connectors:
1. Insert the wires into the connector.
2. Use a crimping tool or pliers to evenly press down
on the head of the connector.
Align to marked latch line
DO NOT PHOTOCOPY AS DIMENSION COULD EXIST TOLERANCE
35mm
Cut 35mm of depth
from jamb edge.
Front face of lock latch
Strike Housing
Refer to the supplied template. Verify lock compatibility and determine the
reference line on the template.
Latch bolt centerline
Cylindrical lock centerline
3
5mm
Fasten the mounting tabs
to the frame.
Connect the wires using
the crimp connectors, then
test the strike, ensure to
give it correct voltage.
Crimp
Connectors
Electric Strike Installations
35
mm
Cu
t 35mm of depth
fr
om jamb edge.
Align to marked l
atch line
Front face of lo
ck latch
Latch bolt centerline
35m
m
Cut
35mm of depth
fro
m jamb edge.
Align to m
arked latch line
Front face
of lock latch
Measure latch position
and mark on the frame.
Attach the template to the
frame and align the
reference line with the
marked line.
Drill and cut the frame
according to the template.
Latch bolt centerline
Note:
Proper gap must be reserved between the strike keeper and latch bolt to prevent solenoid valve failure.
Deadbolt
Keeper
Deadlatch
Ramp
Adjusting Deadbolt Keeper:
Extend the deadbolt, move the
door close to the strike, and let
the deadbolt touch the strike
keeper. Mark deadbolt lines on
the strike keeper. Open the door
and adjust the deadbolt keeper
up and down to align with the
marked lines.
Adjusting Deadlatch Ramp:
Move the door close to the strike.
When the deadlatch touches the
strike keeper, mark deadlatch
lines on the strike keeper. Open
the door and adjust the deadlatch
ramp up and down to align with
the marked lines.
For cylindrical lock applications,
remove the keeper sliding shim
from the strike to ensure proper
latch throw depth.
Cylindrical Lock
Keeper Sliding Shim
Adjusting Keeper Sliding Shim
For Mortise Locks
To minimize door play, slide the
keeper shim up and down to align
with the latch bolt position.
Keeper Sliding Shim
Up
and
down
Up
and
down
Keeper
Keeper
Optional Latch Monitor SW1300 Installations
}
Latch monitor wires
Rated: 1.5A/40VDC
White: COM.
Grey:N.C.
Brown: N.O.
Test the door to make sure that the latch depresses
the latch monitor lever. If not, trim the 3 ribs on
the lever using side cutters.
Move the door towards
the strike.
Mark latch limit lines on
the keeper.
Remove the strike. Mount the SW1300
(latch monitor) and align
with the marked lines on
the keeper.
Test to see if any adjustment
is necessary.
Copyright Gianni Industries Inc All Rights Reserved
P-MU-GK1300 Published:2017.12.05
Sticker Template Instruction
Electric Strike Adjustment
3
1
2
3
4
5
1 2 3
4 5
Up
and
down
Mortise Lock
Latchbolt
For Cylindrical Locks
/
