LBL Lighting HS616GOBZLEDS830MPT Installation guide

LBL Lighting
Brand
LBL Lighting
Model
HS616GOBZLEDS830MPT
Type
Installation guide

The LBL Lighting HS616GOBZLEDS830MPT is a dimmable LED pendant light fixture perfect for indoor dry locations. It features a sleek, modern design with a glass shade and a variety of finish options to match any décor. The fixture is easy to install and comes with all the necessary hardware. It is suitable for use at any height above the finished floor. With a maximum wattage of 8 watts, it provides ample warm white light while saving energy. This fixture is a stylish and functional addition to any home or office.

The LBL Lighting HS616GOBZLEDS830MPT is a dimmable LED pendant light fixture perfect for indoor dry locations. It features a sleek, modern design with a glass shade and a variety of finish options to match any décor. The fixture is easy to install and comes with all the necessary hardware. It is suitable for use at any height above the finished floor. With a maximum wattage of 8 watts, it provides ample warm white light while saving energy. This fixture is a stylish and functional addition to any home or office.

Installation Instructions for
1
Dahling Pendant
980FSJDHLNG
GP I :ENERAL RODUCT NFORMATION
This product is ETL listed and suitable only for indoor dry locations
and approved for use at any height above the finished floor.
Fusion Jack™
1.2
HS616_
SOCKET
LAMP
1A
Push the lamp pins completely into the socket holes.
For incandescent versions, use MAX 50
Watt
Type Xelogen (Xenon) Bi-Pin Lamp.
1
CAUTION: RISK OF FIRE
Never replace a Xenon lamp with a regular Halogen
lamp.A Halogen lamp requires a protective glass shield.
Assemble the Fixture
Place the hardware inside the glass shade and install the
three mounting rods by screwing them in completely.
2
1B
2
MOUNTING ROD MOUNTING ROD
GLASS
SHADE
NOTE: To reduce the risk of a burn or electric shock
during relamping, disconnect the power to the fixture.
For LED versions, use provided MAX 8 Watt
LED Bi-Pin Lamp.
2
Adjust the Fixture Height
Back out (do not remove) the set screw on tip of the
connector with the provided Allen wrench.
Back out (do not remove) the set screw on the conical
connector with the provided Allen wrench.
SET SCREW
ALLEN WRENCH
2
2A
2B
2
1
SET SCREW
ALLEN WRENCH
1
CONNECTOR
2C
Tap the conical connector on a hard surface with the set screw
facing down, so the plate inside drops into place.
SURFACE
Cut the coaxial cable to the desired length.
Gently twist the end of the coaxial cable between thumb and
forefinger.
4
PLATE
3
4
2D
5
2E
6
Feed and push the coaxial cable into the conical connector.The
coaxial cable will come to a stop point after being inserted
3/4" into the conical connector.
CONICAL CONNECTOR
OUTER WRAPPED
WIRE STOPS HERE
6
INNER WIRE
STOPS HERE
2F
Keep pushing the coaxial cable into the connector while
rotating the connector to ease feeding the inner wire into the
tip of the connector.The outer wrapped wire will start
wrinkling while being inserted another 1/2" into the connector.
WRINKLE ON OUTER
WRAPPED WIRE
7
7
Look into the sight hole on the top of the connector to make
sure that the inner wire is contacting the end of the connector.
Hold the coaxial cable in place and tighten the set screw on tip
of the connector with the provided Allen wrench. Make sure
this set screw connection is tight.
SIGHT HOLE
ALLEN WRENCH
9
INNER WIRE
2G
8
9
8
3
Replacing the Lamp
GLASS SHADE
NOTE: To reduce the risk of a burn or electric shock
during relamping, disconnect the power to the fixture.
Lift the glass shade up to expose the lamp and socket.
SOCKET
3A
1
1
SOCKET
LAMP
1
3B
NOTE: Use only your fingers to replace the lamp.
Remove the old lamp.
Push the new lamp pins completely into the socket holes.
Use Type XelogenMAX 50 Watt
(Xenon) Bi-Pin Lamp.
2
CAUTION: RISK OF FIRE
Never replace a Xenon lamp with a regular Halogen lamp.
A Halogen lamp requires a protective glass shield.
GLASS SHADE
SOCKET
3C
4
3
Lower the glass shade until the socket is properly inside the
socket assembly.
3
2H
Firmly tighten the set screw on the conical connector.
10
10
Pull the coaxial cable toward the fixture to smooth the
wrinkles.
2I
11
11
For LED versions, use provided MAX 8 Watt
LED Bi-Pin Lamp.
4
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2015 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
SAVE THESE INSTRUCTIONS!
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LBL Lighting HS616GOBZLEDS830MPT Installation guide

LBL Lighting
Brand
LBL Lighting
Model
HS616GOBZLEDS830MPT
Type
Installation guide

The LBL Lighting HS616GOBZLEDS830MPT is a dimmable LED pendant light fixture perfect for indoor dry locations. It features a sleek, modern design with a glass shade and a variety of finish options to match any décor. The fixture is easy to install and comes with all the necessary hardware. It is suitable for use at any height above the finished floor. With a maximum wattage of 8 watts, it provides ample warm white light while saving energy. This fixture is a stylish and functional addition to any home or office.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents