Your telephone equipment is approved for connection to the Public Switched Telephone
Network and is in compliance with parts 15 and 68, FCC Rules and Regulations and the
Technical Requirements for Telephone Terminal Equipment published by ACTA.
On the bottom of this equipment is a label indicating, among other information, the US
number and Ringer Equivalence Number (REN) for the equipment. You must, upon request,
provide this information to your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone
line and still have all of these devices ring when your telephone number is called. In
most (but not all) areas, the sum of the RENs of all devices connected to one line should
not exceed 5. To be certain of the number of devices you may connect to your line as
determined by the REN, you should contact your local telephone company.
A plug and jack used to connect this equipment to the premises wiring and telephone
network must comply with the applicable FCC Part 68 rules and requirements adopted
by the ACTA. A compliant telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that is also compliant. See
installation instructions for details.
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own
telephone equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your
telephone from your line.
• If your home has specially wired alarm equipment connected to the telephone line,
ensure the installation of this product does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone company or a
qualied installer.
Should your equipment cause trouble on your line which may harm the telephone network,
the telephone company shall, where practicable, notify you that temporary discontinuance
of service may be required. Where prior notice is not practicable and the circumstances
warrant such action, the telephone company may temporarily discontinue service
immediately. In case of such temporary discontinuance, the telephone company must: (1)
promptly notify you of such temporary discontinuance; () afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission
pursuant to procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
3
The telephone company may make changes in its communications facilities, equipment,
operations or procedures where such action is required in the operation of its business and
not inconsistent with FCC Rules and Regulations. If these changes are expected to affect the
use or performance of your telephone equipment, the telephone company must give you
adequate notice, in writing, to allow you to maintain uninterrupted service.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference; and () This device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television
that is “receiving” the interference).
• Reorient or relocate and increase the separation between the telecommunications
equipment and receiving antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that
to which the receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an
experienced radio/television technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful booklet, “How To Identify and Resolve
Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing
Ofce, Washington, D.C. 040. Please specify stock number 004-000-00345-4 when ordering
copies.
Notice: The changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
4
This telephone system meets FCC standards for Hearing Aid Compatibility.
Licensed under US Patent 6,47,009.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 0
centimeters between the radiator and your body. This transmitter must not be co-located or
operated in conjunction with any other antenna or transmitter.”
For body worn operation, this phone has been tested and meets the FCC RF exposure
guidelines when used with the belt clip supplied with this product. Use of other accessories
may not ensure compliance with FCC RF exposure guidelines.
This telephone is compliant with the DECT 6.0 standard which operates in the
1.9GHz to 1.93GHz frequency range. Installation of this equipment is subject
to notication and coordination with UTAM. Any relocation of this equipment
must be coordinated through and approved by UTAM. UTAM may be contacted
at 1-800-49-886.
SEE M ARKIN G ON BOTT OM / BACK OF P RODUC T
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
5
EquipmEnt ApprovAl informAtion .................2
i
ntErfErEncE informAtion .............................3
H
EAring Aid compAtibility (HAc) .................4
l
icEnsing .....................................................4
fcc rf r
AdiAtion ExposurE stAtEmEnt ........4
i
nformAtion for dEct product ..................4
t
AblE of contEnts .......................................5
i
ntroduction ...............................................7
b
EforE you bEgin ........................................7
P
arts CheCklist ........................................... 7
Make sure your PaCkage
inCludes the iteMs shown here. ......................7
t
elePhone JaCk requireMents.........................8
i
nstAllAtion .................................................9
d
igital seCurity systeM ...................................9
i
MPortant installation guidelines .................9
H
AndsEt lAyout .........................................10
b
AsE lAyout ...............................................11
i
nstAlling tHE pHonE ..................................11
i
nstalling the handset Battery ...................11
B
ase station ....................................................12
B
luetooth
®
setuP .........................................13
C
onneCt ......................................................13
d
isConneCt .................................................13
r
eConneCt ..................................................13
p
rogrAmming informAtion .........................14
p
rogrAmming tHE HAndsEt ........................14
P
hone Book ....................................................14
a
dding Phone Book entries ...................14
s
toring the last nuMBer dialed ........... 16
i
nserting a Pause
in the dialing sequenCe ...........................16
r
eviewing Phone Book reCords ............16
e
diting a Phone Book reCord ................17
d
eleting a Phone Book reCord .............17
M
anaging the reCord grouPing
in Phone Book ...........................................18
a
dding the Phone Book entries
i
n desired grouP .................................18
d
eleting the Phone Book entries
i
n desired grouP .................................18
s
et grouP ring ....................................18
C
hanging the grouP naMe ................ 18
M
anaging sPeed dialing reCord ...........19
a
dding the sPeed dialing nuMBer ...19
e
diting the sPeed dialing nuMBer ... 19
d
eleting the sPeed dialing nuMBer 19
t
ransferring the Phone Book reCord
Between handset(s) ..................................20
C
all reCords ..................................................20
r
eCeived Calls ...........................................20
d
ialed Calls .............................................. 21
a
larM ...............................................................21
s
et alarM tiMe ..........................................21
s
nooze ........................................................22
s
et CyCle tiMe ........................................... 22
s
et alarM Melody ....................................22
s
Cheduler ........................................................22
a
dding a reMinder ....................................23
s
et snooze ............................................23
s
et CyCle tiMe ......................................23
s
et alarM Melody ...............................24
r
eviewing and editing
the reMinder reCord ................................24
d
eleting a reMinder reCord ...................24
e
xtra features ...............................................25
r
ooM Monitoring .....................................25
i
nterCoM oPeration ..................................26
h
andset to handset interCoM Call ......26
r
eCeiving an interCoM Call ....................26
P
ush to talk ..............................................27
P
hone setting ................................................27
l
anguage ....................................................27
s
et date/tiMe ............................................ 28
s
et area Code ...........................................28
t
one/Pulse ................................................. 28
h
andset naMe ...........................................29
r
egistration .............................................. 29
g
loBal de-registration ..........................30
d
efault setting .........................................30
s
ound setting ...............................................31
e
qualizer ....................................................31
6
ringer tone ...............................................31
r
inger voluMe ...........................................32
k
ey tone ..................................................... 32
B
luetooth
®
.....................................................32
d
eviCe info .................................................33
a
uto ConneCt ............................................ 33
t
ElEpHonE opErAtion .................................34
v
isual indiCators ...........................................34
in use i
ndiCator on the Base ...............34
talk i
ndiCator and sPkr
i
ndiCator on the handset ........................34
vMwi i
ndiCator on handset .................34
s
PeakerPhone oPeration ...............................34
v
oluMe settings .............................................34
M
aking a Call.................................................34
l
andline Calls ........................................... 34
C
ellular Calls ..........................................35
a
nswering a Call ..........................................35
l
andline Calls ........................................... 35
C
ellular Calls ..........................................35
r
eCeiving a landline Call
during a Cellular Call ............................35
r
eCeiving a Cellular Call
during a landline Call ............................36
r
eCeiving land line Call
a
nd Cell Call siMultaneously ............... 36
a
vailaBle oPtions during
a landline Call .............................................36
M
ore............................................................36
h
old.......................................................36
i
nterCoM ................................................ 37
a
vailaBle oPtions during a Cell Call ......37
M
ore............................................................37
h
old.......................................................37
i
nterCoM ................................................ 37
t
ransfer to Cell ..................................37
C
onferenCe ...............................................38
3-
way ConferenCe Calls with a single
outside landline or Cellular Call and
either ......................................................38
4-
way ConferenCe Calls with an
outside landline and Cellular Call
siMultaneously ......................................38
C
all tiMer .......................................................38
a
uto standBy .................................................. 39
f
lash/Call waiting ......................................39
l
ast nuMBer redial .......................................39
P
age ..................................................................39
P
aging froM the Base/grouP Page .......40
M
ute .................................................................40
r
inger voluMe (shortCut) ............................ 40
c
AllEr id (cid) .........................................40
C
all waiting Caller id ................................41
Cid e
rror Codes ........................................... 41
r
eCeiving Cid reCords ................................. 41
s
toring Cid reCords (in Cid MeMory) ..... 41
r
eviewing Cid reCords ................................42
d
ialing a Cid nuMBer ..................................42
f
orMatting a Cid nuMBer
B
efore dialing ................................................42
s
toring Cid reCords
into Phone Book ............................................43
d
eleting a Cid reCord .................................44
c
onnEcting tHE bElt clip ...........................44
c
onnEcting optionAl HEAdsEt ...................44
c
HAnging tHE bAttEry ................................44
b
AttEry sAfEty prEcAutions .......................45
d
isplAy mEssAgEs .......................................45
H
AndsEt sound signAls .............................47
t
roublEsHooting guidE ..............................47
t
elePhone solutions ..................................... 47
C
aller id solutions ......................................49
B
attery solutions ..........................................49
A
ccEssory informAtion ..............................50
c
AusEs of poor rEcEption ..........................50
g
EnErAl product cArE ..............................50
W
ArrAnty AssistAncE .................................51
l
imitEd WArrAnty ......................................51
i
ndEx .........................................................54
7
Make sure your package includes the items shown here.
8
For there will be additional handset, charge cradle,
belt clip, battery pack and cover than shown.
For there will be additional handsets, charge cradle,
belt clips, battery packs and covers than shown.
For there will be additional handsets, charge cradle,
belt clips, battery packs and covers than shown.
For there will be additional handsets, charge cradle,
belt clips, battery packs and covers than shown.
For there will be additional handsets, charge cradle,
belt clips, battery packs and covers than shown.
For there will be additional handsets, charge cradle, belt
clips, battery packs and covers than shown.
To use this phone, you need an RJ11C type modular telephone
jack, which might look like the one pictured here, installed in your
home. If you don’t have a modular jack, call your local phone
company to nd out how to get one installed.
9
Your cordless phone uses a digital security system to protect against false ringing,
unauthorized access, and charges to your phone line.
• Avoid sources of noise and heat, such as motors, uorescent lighting, microwave
ovens, heating appliances and direct sunlight.
• Avoid areas of excessive dust, moisture and low temperature.
• Avoid other cordless telephones or personal computers.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specically
designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the telephone line
has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
10
56
4
6
3
5
11
1. Locate battery and battery door which are packaged together inside a plastic bag
and are separate from the handset.
. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
1
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.
6. Place the handset in the charging cradle.
PRESS DOWN
FIRMLY
1. Choose an area near an electrical outlet
and a telephone wall jack (RJ11C), and
place your cordless telephone on a level
surface, such as a desktop or tabletop.
. Plug one end of the telephone line cord
into the TEL LINE jack on the bottom of
the base and the other end into a modular
jack.
3. Plug the AC power converter into the
electrical outlet and the DC connector into the jack on the bottom of the base.
4. Place the handset in the charge cradle. The Charge indicator turns on, verifying the
battery is charging.
5. Use the number keys to enter the year and the date.
6. Press the
button to move to Set Time menu.
13
7. Use the number keys to enter the time and use the or button to select
AM or PM.
8. Press the
button to save the settings. You will hear a conrmation tone.
9.
This unit supports a maximum of two Bluetooth cell phone devices. To use you
Bluetooth cell phone device with the 817 System, you must activate Bluetooth on
your device and then pair the device to the base.
1. Make sure your phone is (not in talk mode).
. Press and hold the
or button on base until the corresponding LED
ashes.
When “CELL FUSION” is shown on the device.
3. Use the number keys to enter the default PIN
0000 on your Bluetooth cell phone
device. When the device is paired successful, the corresponding LED illuminates.
Press and hold the or button to disconnect the Bluetooth cell phone.
The or indicator will no longer be illuminated.
Press and release the or button again and the connection will resume.
14
The handset menus give you access to all of the built-in features.
Press the Menu (SKL) button to display the menu options, then press the or
button to navigate to the desired option. Press the button to activate
a menu option. For details on programming, refer to the applicable section. During
programming, you may press the button at any time to exit the menu and
keep the previous setting.
Use the number keys to enter characters. More than one letter is stored in each of the
number keys. For example, press the key twice for the letter B. Press the 1 key to
insert a space. Press the button to toggle between upper and lower case.
There are eight programmable menus available: Phone book, Call records, Alarm,
Scheduler, Extra Features, Phone setting, Sound settings and Bluetooth.
Each handset can store up to two hundred entries in phone book for quick dialing,
each entry can contain a maximum of 0-digit numbers and 15-character names.
For each entry you can enter up to 4 separate numbers and then assign a specic
melody. The melody will work if you have subscribed to the Caller ID service.
Then when that person calls, the assigned melody will ring instead of the normal ring.
You may choose from 5 different ring tones.
1. Make sure your phone is
(not in talk mode).
. Press the
button and use the or button to scroll to Phone
Book.
15
3. Press the button to enter the phone book.
Add
Record
4. Press the button to enter submenu.
5. Use the
or button to scroll to Add Record.
6. Press the
button to conrm. Phone book memory space shows on the
display for seconds. The screen displays Enter Name.
7.
Use the number keys to enter a name ( up to 15 characters, including spaces).
More than one letter is stored in each of the number keys. (The number 1 key can
be used to enter “space”,”-”,”*”, and “!”)
8. Press button to move to save the name and proceed to Enter Number
screen.
9. Use the number keys to enter the telephone number (up to 0 digits).
10. Use the or
button to select from the desired category; Home, Ofce, Cell
or Other.
11. Press the
button to save the number.
• Use the
or button to scroll to Add Number.
• Press the
button to conrm.
• Use number keys to enter the telephone number.
• Use the
or
button to select from the desired category.
• Press the
button to save the number.
1. Use the
or button scroll to Ring Tone.
13. Press the
button and use the or
button to scroll to desired
ringtone.
16
14. Press the button to conrm.
Store a dialed number when reviewing it:
1. Make sure the phone is
(not in talk mode).
. Press the
button on the handset to access the Dialed Calls menu.
3. Use the
or
button to scroll to desired record.
4. Press the
button to save the number.
5. Use the
or
button to select from the desired category; Home, Ofce, Cell
or Other.
6. Press the
button to conrm. The screen displays Enter Name.
7. Use the number keys to enter a name (up to 15 characters, including spaces). More
than one letter is stored in each of the number keys. (The number 1 Key can be
used to enter “space”, “-”, “*” and “!”)
8. Press the
button to save the record.
Press the button on the handset to insert a delay in dialing sequence
of a stored number when a pause is needed to wait for a dial tone (for example, after
you dial 9 for an outside line, or to wait for a computer access tone.) Each pause
counts as one digit in the dialing sequence.
You can press the button to insert a P (pause) when you enter the
telephone number when adding a phone book entry.
1. Make sure your phone is (not in talk mode).
. Press the
button and use the or
button to scroll to Phone
Book.
3. Press the
button to enter the phone book.
4. Use the or button to scroll the records
17
- OR -
Press the number keys to go to the name of the records started with the
corresponding character.
5. Press the button to view the details of the record.
1. When reviewing the phone book records list, use the or button to scroll
to the desired record or enter the rst character of name for alphabetical search.
. Press
button to access the option menu.
3. Use the
or button to scroll to Edit Record.
4. Press the
button to conrm. The screen displays the detail information of
desired record.
5. Use the
or button to scroll to desired edit item.
6. Press the
button.
7. The steps to edit are the same as steps in the section Adding Phone Book Entries.
• Step 7 if you are editing the name.
• Step 9 if you are editing the number.
• Step 11 if you are editing the category.
• Step 1 VIP ring you are editing the VIP ring tone.
1. When reviewing the phone book records list, use the or button or the
number keys to scroll to the desired record.
. Press
button to access the option menu.
3. Use the
or button to scroll to Delete Record.
4. Press the
button. The screen displays DELETE?.
5. Press the
button to conrm the deletion. The screen displays DELETED.
DELETE?
18
This enables you to group a selection of records together, then specify a certain
ringtone for the group.
1. Make sure your phone is
(not in talk mode).
. Press
the button to short-cut to phone book menu.
3. Use the
or button to scroll to desired record.
4. Press the
button to access the Option menu.
5. Use the
or button to scroll to Grouping.
6. Press the
button and use the or button to select desired
group.
7. Press the
button to conrm. The screen displays 5 items for grouping.
GROUPING
1. Use the
or button to select the Add Member menu.
. Press the
button to conrm the selection.
GROUPING
1. Press the
button and use the or button to scroll to Delete
Member.
. Press the
button to conrm the selection.
GROUPING
1. Press the
button and use the or button to scroll to Set
Group Ring.
. Use the
or button to scroll to desired ring tone.
3. Press
button to conrm the .
GROUPING
1. Press
button and use the or button to scroll to Rename.
19
. Use the number keys to enter a name (up to 15 characters, including space.)
3. Press the button to save the new group name.
1 Make sure your phone is (not in talk mode).
. Press
the
button to short-cut to phone book menu.
3. Use the
or button to scroll to desired record.
4. Press the
button to access the option menu.
5. Use the
or button to scroll to Speed Dialing.
6. Press the
button and use the or button to select desired
location. (Up to 10 locations, 0 to 9)
7. Press
the button to conrm.
1. Make sure your phone is (not in talk mode).
. Press
the button to short-cut to phone book menu.
3. Press the
button to access the option menu.
4. Use the
or button to scroll to Speed Dialing.
5. Press the
button and use the or button to select desired
location.
6. Press the
button to access the option menu.
7. Use the
or button to scroll to Edit Number.
8. Press the
button. The screen displays the phone book records.
9. Use the
or button to scroll to desired record.
10. Press
button to conrm the selection.
1. Follow steps 1 to 6 in section “Editing the Speed Dialing Number”.
. Use the
or button to scroll to Delete Number.
0
3. Press the button. The screen displays DELETE?.
4. Press the
button to conrm the selection. The screen displays DELETED.
1. Make sure your phone is (not in talk mode).
. Press
the button to short-cut to phone book menu.
3. Use the
or button to scroll to desired record.
4. Press the
button to access the option menu.
5. Use the
or button to scroll to Transfer Record.
6. Press the
button and the screen displays the list of registered handsets.
7. Use the
or button to scroll to desired handset.
8. Press the
button to conrm the selection. After the transfer process
nish, the screen displays Successful.
This option allows you to redial the number from a CID records or Dialed calls. There
are maximum 40 CID records and 10 dialed calls stored in handset unit.
1. Make sure your phone is
(not in talk mode).
. Press the
button to enter the main menu.
3. Use the
or button to scroll to Call Records.
4. Press the
button to enter the submenu.
CALL RECORDS
1. Use the or button to scroll to Received Calls.
. Press the
button to conrm, a total of All calls and New calls displays.
3. Press the
button and the calls are shown in the order of the most recent
date & time the calls was received.
4. Press
the or button to scroll to the records for desired record
5. Press the
button to see more options.
6. Press
the or button to select Format or Store.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
