protech BM-0962 User manual

USER’S

MANUAL

BM-0962

Mini ITX Motherboard supports

Intel

®

Bay Trail SOC with

DVI/ LVDS/ Audio/ 2LAN/6COM

BM-0962 M3

BM-0962

Mini ITX MotherBoard supports

Intel® Bay Trail SOC

With DVI/ LVDS/ Audio/ 2LAN/

6COM

COPYRIGHT NOTICE & TRADEMARK

All trademarks and registered trademarks mentioned herein are the property of their

respective owners.

This manual is copyrighted in Dec. 2016. You may not reproduce or transmit in

any form or by any means, electronic, or mechanical, including photocopying and

recording.

DISCLAIMER

This operation manual is meant to assist both Embedded Computer manufacturers

and end users in installing and setting up the system. The information contained in

this document is subject to change without any notice.

CE NOTICE

This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

FCC NOTICE

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

You are cautioned that any change or modifications to the equipment not

expressly approve by the party responsible for compliance could void your

authority to operate such equipment.

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the

same or equivalent type recommended by the manufacturer. Dispose of used batteries

according to the manufacturer’s instructions.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual…............................................................

1-2

1-2 System Specification…..........................................................

1-3

1-3 Safety Precautions….............................................................

1-6

CHAPTER 2 HARDWARE CONFIGURATION

2-1 Jumper & Connector Quick Reference Table…....................

2-2

2-2 Component Locations….…...................................................

2-3

2-3 How to Set Jumpers…...........................................................

2-4

2-4 Clear CMOS Data Selection………………………………..

2-6

2-5 LVDS Power Selection…….…………………………….....

2-6

2-6 Backlight/Inverter PWM Voltage Selection…….………….

2-7

2-7 Power-On Mode Selection………………….........................

2-8

2-8 Backlight Enable Selection...………………………..……...

2-9

2-9 VGA/DVI Selection..….……………………………………

2-10

2-10 LVDS Resolution Selection….……………………………..

2-11

2-11 COM3 Voltage Selection…………...………………………

2-14

2-12 COM4 Voltage Selection………………………..………….

2-15

2-13 Audio Port………………….……………………………….

2-16

2-14 Battery Wafer……………………………..………………...

2-17

2-15 COM Port………………...…………………………………

2-17

2-16 COM4 Connector……………...……………………………

2-18

2-17 COM5 Connector……………...……………………………

2-19

2-18 COM6 Connector……………...……………………………

2-19

2-19 DVI-I & COM Port…………………………………………

2-20

2-20 Fan Connector..……………………………………………..

2-21

2-21 DC 12V Connector………..………………………………...

2-21

2-22 DIO Wafer…………………………………………………..

2-22

2-23 Front Connector…………………………………………….

2-22

2-24 Inverter Wafer………………………………………….…...

2-23

2-25 KB/MS Port…………………..……………………….…...

2-24

Contents

2-26 LAN & USB2.0 Port…………………..……………….…...

2-25

2-27 LAN & USB2.0/3.0 Port…………………..…………...…...

2-26

2-28 LVDS Connector…………………………..…………...…...

2-27

2-29 SATA Connector…………………..……..…………….…...

2-28

2-30 SATA Power Connector…………………..…………...…...

2-28

2-31 USB Connector…………………………..……..……...…...

2-28

2-32 Mini PCIE Connector……………………..…………...…...

2-29

2-33 PCIE Bus………..………………………..……..……...…...

2-30

2-34 LPC Connector.………………………..……..……...….......

2-31

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction……………..........................................….........

3-2

3-2 Intel

®

Chipset Software Installation Utility……..……..…...

3-3

3-3 Intel

®

Trusted Execution Engine Installation Utility……….

3-4

3-4 VGA Driver Utility………………………………….……...

3-5

3-5 LAN Driver Utility……...........................................….........

3-6

3-6 Sound Driver Utility………………………………………..

3-7

CHAPTER 4 BIOS SETUP

4-1 Introduction….......................................................................

4-2

4-2 Entering Setup…...................................................................

4-4

4-3 Main…………......................................................................

4-6

4-4 Advanced…...........................................................................

4-8

4-5 Chipset…...............................................................................

4-32

4-6 Security…..............................................................................

4-39

4-7 Boot….…..............................................................................

4-40

4-8 Save & Exit….......................................................................

4-43

APPENDIX A EXPANSION BUS

PCIe Bus………………………………….......................................

A-2

APPENDIX B TECHNICAL SUMMARY

Block Diagram…..............................................................................

B-2

Interrupt Map…................................................................................

B-3

Contents

Memory Map….……………………………………………………

B-7

I/O Map…........................................................................................

B-9

Watchdog Timer Configuration….………………...………………

B-11

Flash BIOS Update…...............................................…....................

B-14

Page:1-1

INTRODUCTION

This chapter gives you the information for BM-0962. It also outlines

the system specifications.

The following sections are included:

 About This Manual

 System Specifications

 Safety Precautions

Experienced users can go to chapter 2 on page 2-1 for

a quick start.

CHAPTER

1

Chapter 1 Introduction

BM-0962 USER



S MANUAL

Page: 1-2

1-1. ABOUT THIS MANUAL

Thank you for purchasing our BM-0962 Mini-ITX Motherboard with Intel

®

Atom

E3815/ E3827/ J1900/ N2930/ N2807 processor, enhanced with LAN, VGA, 6

USB & 6COM, which is fully PC/AT compatible. The BM-0962 provides faster

processing speed, greater expandability and can handle more tasks than before.

This manual is designed to assist you how to install and set up the system. It

contains four chapters. The user can apply this manual for configuration according

to the following chapters:

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the

specifications for this system. The final page of this chapter will indicate how to

avoid damaging this board.

Chapter 2 Hardware Configuration

This chapter outlines the component locations and their functions. In the end of

this chapter, you will learn how to set jumper and how to configure this card to

meet your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the VGA

utility, LAN utility and Sound utility.

Chapter 4 BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This appendix introduces you the expansion bus for PCIe connectors.

Appendix B Technical Summary

This appendix gives you the information about the Technical maps and Flash BIOS

Update. It also describes the Watchdog-timer configuration.

Chapter 1 Introduction

BM-0962 USER



S MANUAL

Page: 1-3

1-2. SYSTEM SPECIFICATIONS

System

CPU

 Intel

®

Atom E3815 (5W, 1.46GHz, 1C/1T)

 Atom E3827 (8W, 1.75GHz, 2C/2T)

 Atom J1900 (10W, 2GHz, 4C/4T)

 Atom N2930 (7.5W, 1.83GHz, 4C/4T)

 Atom N2807 (4.3W, 1.58GHz, 2C/2T)

OS Support

Windows 8, 7

Chipset

Bay Trail-I SOC

Co-lay Bay Trail-D/Bay Trail-M SOC

Memory

2 x 204-pin DDR3L SO-DIMM, support dual-channel

DDR3L 1333/1600MHz (system max. 8GB)

* If there is only one SO-DIMM, SO-DIMM1 should be

inserted first instead of SO-DIMM2.

BIOS

AMI

Watchdog

1~255 seconds

Power Supply

DC 12V in

Dimension

170 mm x 170 mm (6.69” x 6.69”)

Certificate

CE/FCC Class A

Chapter 1 Introduction

BM-0962 USER



S MANUAL

Page: 1-4

I/O Ports

Serial Port

6 COM Ports:

 COM1, 2, 3: D-sub 9, rear IO

 COM4, 5, 6: 2.0mm pitch pin header

 COM3,4 support +5/+12V

*COM 5/6 support RS-232/422/485 function via the

daughter board.

* BM-0962-07N and BM-0962-W5N SPEC do not support

COM5 and COM6.

USB Port

6 USB ports:

 5 x USB2.0: (3 x stack w/ LAN connector, rear IO, 2 x

onboard Connector)

 1 x USB3.0: stack w/ LAN connector, rear IO

*BM-0962RA-00N, BM-0962RA-30N and BM-0962RA-

W7N.

4 USB ports:

 3 x USB2.0: stack w/ LAN connector, rear IO

 1 x USB3.0: stack w/ LAN connector, rear IO

*BM-0962RA-W5N and BM-0962RA-07N.

SATA Interface

2 x SATA II, onboard Connector

LAN

 Dual ports are provided to support 10/100/1000Mbps,

RJ-45, rear IO, support Wake-on-LAN

 LAN1: Intel I210-IT/AT

 LAN2: Intel I210- IT/AT

* BM-0962-07N and BM-0962-W5N SPEC only support

one LAN.

Audio

Realtek ALC888S, high definition audio, Line-in/ Line-out/

MIC-in, audio jack, rear IO.

Keyboard/Mouse

1 x PS/2

Expansion Bus

1 x PCIe (1x)

1 x Mini-PCIe

GPIO/ DIO

GPIO 4in / 4out

LPC

1 x LPC pin head (supports TPM module for expansion)

Chapter 1 Introduction

BM-0962 USER



S MANUAL

Page: 1-5

Display

Graphics

1 x DVI-I, rear IO

1 x LVDS(DP),

Dual channel 18/24bit

 *Only support two independent displays

 * BM-0962- 07N SPEC does not support LVDS.

LED Indicator

HDD LED, Power LED, Power Switch, Reset Switch

Speaker

Internal buzzer

Environment

Operating Temp.

0°C~60°C (32°F ~140°F), Wide temp SKU: -40°C ~ 85°C

Storage Temp.

-40°C~80°C (-40°F ~176°F)

Operating Humidity

5%~90% (non-condensing)

Chapter 1 Introduction

BM-0962 USER



S MANUAL

Page: 1-6

1-3. SAFETY PRECAUTIONS

Follow the instructions below to safeguard your system from damages:

1. Keep your system away from static electricity on all occasions.

2. Prevent electric shock. Do not touch any components of the system when the

system is powered on. Always disconnect the power supply when the system is

not in use.

3. Disconnect the power supply when you change any hardware devices.

For instance, when you connect a jumper or install any cards, a surge of power

may damage the electronic components or the whole system.

Page 2-1

HARDWARE

CONFIGURATION

** QUICK START **

CHAPTER

2

Helpful information describes the jumper & connector settings, and

component locations.

The following sections are included:

 Jumper & Connector Quick Reference Table

 Component Locations

 Configuration and Jumper settings

 Connector’s Pin Assignments

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-2

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

JUMPER/CONNECTOR

NAME

Clear CMOS Data Selection

JP1

LVDS Power Selection

JP4

Backlight Power Selection

JP5

AT/ATX Mode Selection

JP7

Backlight Enable Selection

JP9

VGA/DVI Selection

JP10

LVDS Resolution Selection

JP14, JP15

COM3 Voltage Selection

JP_COM3

COM4 Voltage Selection

JP_COM4

Audio Port

JAUDIO1

Battery Wafer

JBAT1

COM Port

JCOM2_3

COM4 Connector

JCOM4

COM5 Connector

JCOM5

COM6 Connector

JCOM6

DVI-I & COM Port

JCOM_DVII1

FAN Connector

JCPU_FAN1, JSYS_FAN1

DC 12V Connector

JDC_PWR1

DIO Wafer

JDIO1

Front Connector

JFP1

Inverter Wafer

JINV1

KB/MS Port

JKB_MS1

LAN & USB2.0 Port

JLAN_USB1

LAN& USB2.0/3.0 Port

JLAN_USB2

LVDS Connector

JLVDS1

SATA Connector

JSATA1, JSATA2

SATA Power Connector

JSATA_PWR1, JSATA_PWR2

USB Connector

JUSB1

MINI PCIE Connector

M_PCI_E1

PCIE BUS

PCI_E1

LPC Connector

JLPC1

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-3

2-2. COMPONENT LOCATIONS

BM-0962 Connector, Jumper and Component Locations (Front Side)

JCOM_DVII1

JCOM2_3

JAUDIO1

JSATA_PWR1

DIMM2

DIMM1

JSATA2

JSATA1

JCPU_FAN1

JLAN1_USB2

JLAN_USB1

JKB_MS1

SP1

JP10

1

2

5

6

1

4

1

7

17

1

2

71

72

73

74

203

204

JPCOM4

JPCOM3

JSYS_FAN1

2

65

1

5

2

1

JLVDS1

30

291

2

6

JINV1

1

MPCI_E1

1 4

JCOM5

JCOM4

1

5

6

1

6

10

5

10

JCOM6

JFP1

12

11

2

1

JP7

1

5

10

1

6

JDIO1

1

2

JUSB1

9

10

1 2

JP14

JP15

1

2

5

6

JP4

1

JP5

1

JP9

PCI_E1

14

JDC_PWR1

14

JSATA_PWR2

JBAT1

Intel® Bay Trail-I/M/D

SOC

JP1

1

2

5

6

1

2

71

72

73

74

203

204

JLPC1

20

19

2

1

2

7

8

A11

A1

A12

A18

B11

B1

B12

B18

1

2

15 16

17 18

51 52

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-4

2-3. HOW TO SET JUMPERS

You can configure your board by setting jumpers. Jumper is consists of two or three metal

pins with a plastic base mounted on the card, and by using a small plastic "cap", Also

known as the jumper cap (with a metal contact inside), you are able to connect the pins.

So you can set-up your hardware configuration by "open" or "close" pins.

The jumper can be combined into sets that called jumper blocks. When the jumpers are all

in the block, you have to put them together to set up the hardware configuration. The

figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You can connect

PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2 & PIN3 to

create another setting. The same jumper diagrams are applied all through this manual. The

figure below shows what the manual diagrams look and what they represent.

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-5

Jumper Diagrams

2 pin Jumper

looks like this

Jumper Cap

looks like this

3 pin Jumper

looks like this

Jumper Block

looks like this

Jumper Settings

Looks like this

3 pin Jumper

2-3 pin close(enabled)

Looks like this

Jumper Block

1-2 pin close(enabled)

2 pin Jumper close(enabled)

1

2

1 2

1

Looks like this

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-6

2-4. CLEAR CMOS DATA SELECTION

JP1: Clear CMOS Data Selection

SELECTION

JUMPTER

SETTING

JUMPER ILLUSTRATION

NC

JP1

Clear CMOS

1-2

JP1

Note: Manufacturing default is NC.

2-5. LVDS POWER SELECTION

JP4: LVDS Power Selection

SELECTION

JUMPTER

SETTING

JUMPER ILLUSTRATION

3.3V

1-2

JP4

5V

2-3

JP4

Note: Manufacturing default is 3.3V.

1

3 1

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-7

2-6. Backlight Inverter PWM Voltage Selection

JP5: Backlight Inverter PWM Voltage Selection

SELECTION

JUMPTER

SETTING

JUMPER ILLUSTRATION

3.3V

1-2

JP5

5V

2-3

JP5

GND

NC

JP5

Note: Manufacturing default is 3.3V.

3

1

3

1

3

1

Chapter 2 Hardware Configuration

BM-0962 USER



S MANUAL

Page: 2-8

2-7. Power-On Mode SELECTION

JP7: Power-On Mode Selection

SELECTION

JUMPTER

SETTING

JUMPER ILLUSTRATION

Auto-on

1-2

JP7

Select by

BIOS

NC

JP7

Note 1: Manufacturing default is Auto-on.

Note 2: Manufacturing default for BS-H292 (SBOX) is "NC".

Note 3: Auto-On means that system will turn on automatically whenever the main power is

restored.

1

Page is loading ...

protech BM-0962 User manual

protech BM-0962 User manual

Related papers

Other documents