ESAB Feed 30-4 M14, Feed 48-4 M14 User manual
- Category
- Welding System
- Type
- User manual
This manual is also suitable for
GB
Valid for serial no. 238--xxx--xxxx0459 160 001 GB 051220
ESABFeed 30- 4 M14
ESABFeed 48- 4 M14
Instruction manual
-- 2 --
TOCe
Rights reserved to alter specifications without notice.
1 DIRECTIVE 3........................................................
2SAFETY 3...........................................................
3 INTRODUCTION 5...................................................
3.1 Equipment 5................................................................
4 TECHNICAL DATA 5.................................................
5 INSTALLATION 6....................................................
5.1 Lifting instructions 7.........................................................
6 OPERATION 7.......................................................
6.1 Connections and control devices 8............................................
6.2 W ater connection 8..........................................................
6.3 Function explanations 9......................................................
6.4 Operation 10................................................................
6.5 Wire feed pressure 13........................................................
6.6 Changing / loading wire ESABFeed 30 13.......................................
6.7 Changing / loading wire ESABFeed 48 13.......................................
6.8 Changing feed rollers on ESABFeed 30 14......................................
6.9 Changing feed rollers on ESABFeed 48 14......................................
7 MAINTENANCE 15....................................................
7.1 Inspection and cleaning 15....................................................
8 ORDERING SPARE PARTS 15..........................................
DIAGRAM 16............................................................
ORDERING NUMBER 17.................................................
WEAR COMPONENTS 18.................................................
ACCESSORIES 22.......................................................
-- 3 --
bm35d1ea
1DIRECTIVE
DECLARATION OF CONFORMITY
ESAB AB Arc Equipment, S--695 81 Laxå, Sweden, declares that wire feed unit ESABFeed 30--4
M14
/ESABFeed 48--4 M14 from serial number 238 onwards, conforms to standard EN 60974--5, in accord-
ance with the requirements of directive (73/23/EEC) and appendix (93/68/EEC) and standard EN
50199 in accordance with the requirements of directive (89/336/EEC) and appendix (93/68/EEC).
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------
Henry Selenius
Vice President
ESAB AB Arc Equipment
695 81 LAXÅ
SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924
Laxå 2002--10--23
2SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen-
dations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1. Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2. The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no--one is unprotected when the arc is struck
3. The workplace must:
S be suitable for the purpose
S be free from drafts
4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof
clothing, safety gloves.
S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5. General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
GB
-- 4 --
bm35d1ea
WARNING
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-
TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S Protect y our eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S Protect y our ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection an d accessories.
WARNING!
Read and understand the instruction manual before installing
or operating.
This product is solely intended for arc welding.
GB
-- 5 --
bm35d1ea
3 INTRODUCTION
The ESABFeed 30--4 and ESABFeed 48--4 wire feed
units with control panel M14 are intended for M IG/MAG--
welding together with welding power sources
ESABMig 400t and ESABMig 500t.
They come in different variants, see on page 17.
The wire feed units are sealed and contain four--wheel
drive wire feed mechanisms as well as control
electronics.
They can be used together with wire on ESAB’s MarathonPact, or on wire bobbin
(standard Ø 300 mm, accessory Ø 440 mm).
The wire feed unit can be installed either at the power source, suspended above the
workplace, on a support arm or on the floor with or without wheel set.
ESAB’s accessories for t he product can be found on page 22.
3.1 Equipment
The ESABFeed 30 wire feed unit is supplied with:
S Instruction manual
S Stickers with recommended wear parts.
The ESABFeed 48 wire feed unit is supplied with:
S Spacer (4)
S Hex key wrench (4 mm)
S Instruction manual
S Stickers with recommended wear parts.
4 TECHNICAL DATA
ESABFeed 30--4 M14 ESABFeed 48--4 M14
Power supply 42 V 50 -- 60 Hz 42 V 50 -- 60 Hz
Power requirement 336 VA 378 VA
Motor current I
max
8A 9A
Settings data
Wire feed speed
Burnback time
Crater filling time
Creep start
2/4 stroke
Synergic lines
1.9--25.0 m/min
0-- 0.5 s
0-- 5.1 s
OFF or ON
2strokeor4stroke
14 pre--set and
2 programmable
1.9--25.0 m/min
0-- 0.5 s
0-- 5.1 s
OFF or ON
2strokeor4stroke
14 pre--set and
2 programmable
Gun connection EURO EURO
Max. diameter wire bobbin 300 mm (*440 mm) 300 mm (*440 mm)
Wire dimension 0.6--1.6 mm 0.6--2.4 mm
GB
-- 6 --
bm35d1ea
ESABFeed 48--4 M14ESABFeed 30--4 M14
Weight
basic version
with sealed bobbin holder
11.5 kg
15 kg
14.5 kg
19 kg
Dimensions (l x w x h)
basic version
with sealed bobbin holder
380 x 275 x 400 mm
690 x 275 x 420 mm
380 x 275 x 400 mm
690 x 275 x 420 mm
Shielding gas
max pressure
All types intended for
MIG/MAG welding
5 bar
All types intended for
MIG/MAG welding
5 bar
Coolant
max pressure
50% water / 50% glycol
5 bar
50% water / 50% glycol
5 bar
Permissible load at
60% duty cycle
630 A 630 A
Enclosure class IP23 IP23
* Accessories, see page 22.
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer-
tain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
5 INSTALLATION
The installation must be execu ted by a p rofession al.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’ s responsibility to take adequate precautions.
WARNING!
When welding in an environment with increased electrical danger , only power sources intended
for this environment may be used. These power sources are marked with the symbol .
GB
-- 7 --
bm35d1ea
5.1 Lifting instructions
Ordering number for the lifting eye can be found on page 22.
Note! If another mounting device is used, this should be insulated from the wire feed
unit.
6OPERATION
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
WARNING!
Assure that the side panels are closed during operation.
To prevent the reel from sliding off the hub: Lock the reel in place by
turning the red knob as shown on the warning label attached next to
the hub.
WARNING!
WARNING!
Rotating parts can cause injury, take great care.
WARNING!
There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm. Secure the
equipment, especially if used on an uneven or sloping surface.
When moving the equipment use intended handle. NOTE! Never pull on the gun.
GB
-- 8 --
bm35d1ea
6.1 Connections and control devices
1 Display 13 Connection for remote control unit
2 Indicating lamp for work point 14 Connection BLUE, with ELP* for cooling
water to the welding gun
3 Indicating lamp for storing welding data 15 Connection RED for cooling water from
welding gun
4 Knob for setting the voltage 16 Connection for welding gun
5 Switch for selecting welding data 1, 2, 3 17 Switch for 2--stroke / 4--stroke
6 Pressure switch for storing welding data 18 Knob for setting burnback time
7 Pressure switch for pre--setting wire feed
and voltage
19 Connection for welding current from power
source, (OKC)
8 Switch
MANUAL, PROGRAM, SYNERGY
20 Connection for control cable from power
source
9 Knob for setting crater filling time 21 Connection RED for cooling water to po-
wer source (cooling unit)
10 Switch for selecting synergic line 22 Connection BLUE for cooling water from
power source (cooling unit)
11 Knob for setting wire feed speed. 23 Connection for shielding gas
12 Switch for creep start OFF / ON
NOTE! Cooling water connections only available on certain models.
* ELP = ESAB Logic Pump, see point 6.2.
6.2 Water connection
When connecting a water-- cooled welding gun, the power source’s main power
supply switch must be in the Off position and the cooling unit switch must be in
position “ELP/0”.
The wir e feed unit with water connection is equipped with a detection system ELP
(ESAB Logic Pump) which checks that the water hoses are connected. When
connecting a water--cooled welding gun, the water pump starts.
Detection only works with power sources that are equipped with ELP.
GB
-- 9 --
bm35d1ea
6.3 Function explanations
Burnback time
Burnback time is a delay between the time when the wire starts to brake until the
time when the power source switches off the welding voltage. Too short burnback
time results in a long wire stickout after completion of welding, with a risk of the wire
being caught in the solidifying weld pool. Too long a burnback time results in a
shorter stickout, with increased risk of the arc striking back to the contact tip.
Crater filling
Crater filling helps to avoid pores, thermal cracking and crater formation in the weld
when welding stops.
Figure 1 shows an interruption in the
welding, and a crack or crater opens up
readily in the solidified central part due
to shrinkage during the solidifying pro-
cess.
Fig. 1. After welding without crater filling
Figure 2 shows that the arc continues to
give off a certain amount of heat while
the weld pool is solidifying. T his chang-
es the s olidification process so that the
last solidified part of the weld pool ends
u
p
a
t
t
h
e
t
o
p
,
a
n
d
in
t
hi
s
w
a
y
i
t
i
s
p
o
s
s
i
b
-
u
p
a
t
t
h
e
t
o
p
,
a
n
d
i
n
t
h
i
s
w
a
y
i
t
i
s
p
o
s
s
i
b
-
le to avoid the occurrence of a crater.
Fig. 2. After welding with crater filling
2stroke
With 2 stroke, wire feed starts when the trigger switch is pressed in and ends when
it is released.
4stroke
With 4 stroke, the gas flow starts when the trigger switch is pressed in and the wire
feed starts when it is released. T he welding process continues until the switch is
pressed in again, the wire feed stops and when the switch is released the gas stops
flowing.
Creep start
Creep start means that the wire is fed at low speed until it comes into electrical
contact with the workpiece and then the speed increases to the set speed.
GB
-- 1 0 --
bm35d1ea
Synergy
Each combination of wire type, wire diameter and gas mixture requires a unique
relationship between wire feed speed and voltage (arc length) to obtain a stable
functioning arc. T he wire feed unit has pre--programmed ‘synergic lines’.
When you select the pre--programmed synergic line corresponding to your wire type,
wire diameter and gas mixture, you then only need to set an appropriate wire feed
speed for your welding object. The voltage (arc length) automatically conforms in
accordance with the pre-- programmed synergic line you selected
As different welding objects and joints require slightly different voltage (arc length),
this can be finely adjusted on the basis of the pre--programmed value.
Synergic lines make it easy to find the correct welding parameters. You choose the
appropriate synergic line for your welding wire/gas combination and then set the wire
feed speed. The voltage then automatically conforms to the wire feed speed in
accordance with the synergic line.
Wire feed speed
This sets the required feed speed of the filler wire in m /minute.
6.4 Operation
The wire feed unit can be set at ten different operating positions using switch 8 :
MANUAL , PROGRAM and SYNERGY 1 -- 8.
6.4.1 Manual operation
Set switch 8 in position
. Hold down the
“PRESET” button 7 when adjusting the wire feed
11 and voltage 4; the display shows set values for
wire feed and voltage. During welding, the display
shows measured arc voltage and welding current.
Storing the work point
A work point consists of a wire feed speed and a
welding current. Set switch 5 in one of the three
positions 1, 2 or 3. Set wire feed and a voltage.
Press the store button 6 to store the work point. After approximately 2.5 seconds the
green indicating lamp 2 comes on. The lamp remains lit until you r elease the store
button.
You can also store wire feed and welding voltage from a synergic line, see “Storing
work point” on page 12.
GB
-- 1 1 --
bm35d1ea
6.4.2 Program p osition
Set switch 8 in position and switch 5 in the
position containing the data you want to use. If a
welding gun with a program selector switch is
connected to the socket for the remote control unit,
you should select a work point with this. It is also
possible to change work point during welding.
Note: if a remote control unit or a welding gun with
program selection is connected to the socket for the remote control unit, it is not
possible to select work point with switch 5.
Do not press the store button when the function selector switch 8 is in program
position.
In program position, only the stored work points can affect wire feed and voltage. All
other settings for wire feed and voltage are inactive.
6.4.3 Synergic position
You can choose from 16 different synergic lines, of
which two are programmable, see table on page 12
or on the sticker on the inside of the hatch to the
wire feed unit.
Using function selector switch 8 and switch 10,
select the synergic line corresponding to the wire
you intend to use.
With knob 4, set a wire feed speed.
With a voltage potentiometer from a remote control
unit or with knob 4 , you can set a synergic deviation from the calculated arc voltage
reference. If the deviation is zero, the green indicating lamp 2 will be lit. A positive or
negative deviation causes the lamp to go out. If you want to return to the synergic
line, you must readjust the voltage until the green lamp come on again.
The synergic deviation is zeroed when you select a new synergic line.
If a remote control unit is connected, the synergic deviation is not zeroed when the
synergic line is changed. If the remote control unit’s potentiometer is set in the
central position, the synergic deviation will be zero.
Pre--setting
If you press switch 7 you can read off the wire feed and voltage values that are set in
each synergic line. The display shows set wire feed, as well as welding voltage
including any synergic deviation.
GB
-- 1 2 --
bm35d1ea
Storing the work point
You can store an arbitrary point on a synergic line in the same way as you store a
work point in manual operation:
S Select a synergic line.
S Set the desired wire feed and synergic deviation.
S Check the set values by pressing switch 7.
S Using switch 5 select the program where you wish to store the set welding data.
S Press store button 6. After 2.5 seconds the set welding data is stored.
S Green indicating lamp 3 comes on, release the store button 6.
Synergy A Synergy B
1 Fe 1.0 80%Ar 20%CO
2
1 MCW 1.2 80%Ar 20%CO
2
2 Fe 1.2 80%Ar 20%CO
2
2 MCW 1.6 80%Ar 20%CO
2
3 Ss 1.0 98%Ar 2%CO
2
3 RFCW 1.2 80%Ar 20%CO
2
4 Ss 1.2 80%Ar 20%CO
2
4 RFCW 1.6 80%Ar 20%CO
2
5 Al Mg 1.2 100%Ar 5 BFCW 1.2 80%Ar 20%CO
2
6 Al Mg 1.6 100%Ar 6 BFCW 1.6 80%Ar 20%CO
2
7 Al Si 1.2 100%Ar 7 Programmable
8 Al Si 1.6 100%Ar 8 Programmable
14 pre--programmed synergic lines.
SSFCW = Stainless Steel Flux Cored Wire
MCW = Metal Cored Wire
RFCW = Rutile Flux Cored Wire
BFCW = Basic Flux Cored Wire
6.4.4 Design your own synergic lines
If the pre--programmed synergic lines do not match your combination of wire type,
wire diameter and gas mixture, use programming box PAH 1, connected to the
socket for the remote control unit, to make two of your own synergic lines and store
them in the wire feed unit’s memory.
PAH 1 is an accessory. Order number, see page 25.
GB
-- 1 3 --
bm35d1ea
6.5 Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder’s pressure rollers. It is important that the
pressure is not too great.
Fig 1 Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
6.6 Changing / loading wire ESABFeed 30
S Open the side panel.
S Disconnect the pressure sensor by folding it backwards, the pressure rollers
slide up.
S Straighten out the new wire 10--20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
S Make sure that the wire goes properly into the feed roller’s track and into the
outlet nozzle or wire guide.
S Secure the pressur e sensor.
S Close the side panel.
6.7 Changing / loading wire ESABFeed 48
S Open the side panel.
S Press down and pull the pressure device towards you and up.
S Pull out the bogie.
S Straighten out the new wire 10--20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
S Make sure that the wire goes properly into the feed roller’s track and into the
outlet nozzle or wire guide.
S Reinstall the bogie.
S Close the side panel.
GB
-- 1 4 --
bm35d1ea
6.8 Changing feed rollers on ESABFeed 30
S Open the side panel.
S Disconnect the pressure sensor (1) by folding it
backwards, the pressure rollers slide up.
S Disconnect the pressure rollers (2) by turning the
axle (3) 1/4 turn clockwise and pulling out the axle.
The pressure rollers disconnect.
S Disconnect the feed rollers (4) by unscrewing the nuts
(5) and pulling out the rollers.
During installation, repeat the above in the reverse order.
Choice of tracks in th e feed rollers
Turn the feed roller with the dimensioning mark for the required
track towards you.
6.9 Changing feed rollers on ESABFeed 48
S Open the side panel.
S Press down and pull the pressure device (1) towards
you and up.
S Pull out the bogie (2).
S Undo the socket head cap screws (3) on the
holder for the intermediate nozzle and remove
the holder.
S Undo the screw for the outlet nozzle ( 4) and
push back the nozzle.
S Completely undo the socket head cap screw
(5) in the centre.
S Undo the two outer socket head cap screws (6) 1/2 a
turn.
S Pull out the feed rollers (7).
During installation, repeat the above in the reverse order.
Choice of tracks in th e feed rollers
Place no, one or two driving washers
between the outer washer and the feed
roller. Note! When replacing the
pressure rollers (8), the entire bogie is
replaced.
GB
-- 1 5 --
bm35d1ea
7 MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
7.1 Inspection and cleaning
Wire feed unit
Check regularly that the wire feed unit is not clogged with dirt.
S Cleaning and replacement of the wire feed unit mechanism’s worn parts should
take place at regular intervals in order to achieve trouble--free wire feed. Note
that if pre--tensioning is set too hard, this can result in abnormal wear on the
pressure roller, feed roller and wire guide.
The brake hub
The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.
S Adjusting the braking torque:
S Turn the red handle to the locked position.
S Insert a screwdriver into the springs in the hub.
Turn the springs clockwise to reduce the braking torque
Turn the springs counterclockwise to increase the braking torque. NB: Turn
both springs through the same amount.
Weldin g gu n
S Cleaning and replacement of the welding gun’s wear parts should take place at
regular intervals in order to achieve trouble--free wire feed. Blow the wire guide
clean regularly and clean the contact tip.
8 ORDERING SPARE PARTS
ESABFeed 30--4/ ESABFeed 48--4 is designed and tested in accordance with the inter-
national and European standards IEC/EN 60974--5 and EN 50199. It is the obligation of
the service unit which has carried out the service or repair work to make sure that the
product still conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
GB
Diagram
-- 1 6 --
bm35e11a
ESABFeed 30- 4 M14, ESABFeed 48- 4 M14
Edition 051220
Ordering number
-- 1 7 --
bm35o11a
1.
Feeder for Marathon Pact Feeder with
capsuled bobbin
ESABFeed 30--4 M14 with water cooling 0459 114 895 0459 116 895
ESABFeed 48--4 M14 with water cooling 0459 114 995 0459 116 995
Spare parts list 0459 160 990 0459 160 990
ESABFeed 30- 4 M14
Edition 051220
Wear p arts
-- 1 8 --
bm29whj1
S= Standard, HD = Heavy Duty
Item
Ordering no. Denomination Wire type Wire dimensions
HI 1 0455 072 002
0456 615 001
Intermediate nozzle (S)
Intermediate nozzle
Fe, Ss & cored
Al
HI 2 0469 837 880
0469 837 881
Outlet nozzle (S)
Outlet nozzle
Fe, Ss & cored
Al
Ø 2.0 mm steel for 0.6--1.6 mm
Ø 2.0 mm plastic for 0.8--1.6 mm
HI 3 0191 496 114 Key
HI 4 0215 701 007 Locking washer
HI 5a 0459 440 001 Motor gear euro
Item Ordering no. Denomination Wire type Wire dimensions Groove
typ
Roller
markings
HI 5b 0459 052 001 Feed/pressure rollers Fe, Ss & cored Ø 0.6 & 0.8 mm V 0.6 S2 &0.8S2
0459 052 002 Feed/pressure rollers Fe, Ss & cored Ø 0.8 & 1,0 mm V
0.8 S2 &1.0S2
0459 052 003 Feed/pressure rollers (S) Fe, Ss & cored Ø 0.9/1.0 & 1.2 mm V 1.0 S2 &1.2S2
0459 052 013 Feed/pressure rollers Fe, Ss & cored Ø 1.4 & 1.6 mm V 1.4 S2 &1.6S2
0458 825 001 Feed/pressure rollers Cored Ø 0.9/1.0 & 1.2 mm V--Knurled 1.0 R2 &1.2R2
0458 825 002 Feed/pressure rollers Cored Ø 1.2 & 1.4 mm V--Knurled 1.2 R2 &1.4R2
0458 825 003 Feed/pressure rollers Cored Ø1.6mm V--Knurled 1.6 R2 &2.0R2
0458 824 001 Feed/pressure rollers Al Ø 0.8 & 0.9/1.0 mm U 0.8 A2 &1.0A2
0458 824 003 Feed/pressure rollers Al Ø 1.2 & 1.6 mm U 1.2 A2 &1.6A2
Use only pressure and feed rollers marked A2, R2 or S2.
Therollersaremarkedwithwiredimensioninmm,somearealsomarkedwithinch.
Item Ordering no. Denomination Notes
HI 6 Washer Ø 16/5x1
HI 7 Screw M4x12
HI 8 Screw M6x12
HI 9 Washer Ø 16/8.4x1.5
HI 10 0469 838 001 Cover
HI 11 0458 722 880 Axle and Nut
HI 12 0459 441 880 Gear adapter
HI 13 0455 049 001 Inlet nozzle
HI 14 0458 999 001 Shaft
HI 15 Nut M10
HI 16 0458 748 002 Insulating washer
HI 17 0458 748 001 Insulating bushing
Item Ordering no. Denomination Notes Wire dimensions
HI 18 0156 602 001
0332 318 001
Inlet nozzle (S)
Inlet nozzle (HD)
Fe, Ss, Al & Cored
Fe, Ss & Cored
Ø 2 mm plastic for 0.6--1.6 mm
Ø 2.4 mm steel for 1.2--2.0 mm
Welding with aluminium wire
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.
ESABFeed 30- 4 M14
Edition 051220
-- 1 9 --
bm29whj1
ESABFeed 48- 4 M14
Edition 051220
-- 2 0 --
bm29whk1
S= Standard, HD = Heavy Duty
Item
Ordering no. Denomination Wire type Wire dimensions
HK1 0469 837 880
0469 837 881
0469 837 882
Outlet nozzle (S)
Outlet nozzle
Outlet nozzle
Fe, Ss & cored
Al
Fe, Ss & cored
Ø 2.0 mm steel for 0.6--1.6 mm
Ø 2.0 mm plastic for 1.0--1.6 mm
Ø 3.4 mm steel for 2.0--2.4 mm
Item Ordering no. Denomination Wire type Wire Ø
mm
Groove 1 Groove 2 Groove 3 Groove
typ
Roller /
Bogey
mark-
ings
HK2 0366 966 880 Feed Roller Fe, Ss & cored 0.6--1.2 0.6--0.8 0.9--1.0 1.2 V 1
0366 966 881 Feed Roller Fe , Ss & cored 1.4--1.6 1.4--1.6 2.0 2.4 V 2
0366 966 889 Feed Roller Fe , Ss & cored 1.2 .045” / 1.2 .045” / 1.2 .045” / 1.2 V .045 / 7
0366 966 900 Feed Roller (S) Fe, Ss & cored 0.9--1.6 0.9--1.0 1.2 1.4--1.6 V 6
0366 966 882 Feed Roller Cored 1.2--2.0 1.2 1.4--1.6 2.0 V--Knurled 3
0366 966 883 Feed Roller Cored 2.4 2.4 not used not used V--Knurled 4
0366 966 885 Feed Roller Al 1.2 1.2 1.2 1.2 U U2
0366 966 899 Feed Roller Al 1.0--1.6 1.0 1.2 1.6 U U4
Item Ordering no. Denomination Notes
HK3 0156 707 001 Distance washer
HK4 0156 707 002 Adjustment spacer
HK5 Screw M5x20
HK6 Screw M5x16
Item Ordering no. Denomination Wire type Wire dimensions Groove
typ
Roller /
Bogey
markings
HK7 0366 902 880 Bogey (HD) Fe, Ss & cored Ø0.6--1.2mm V 1
0366 902 900 Bogey Fe, Ss & cored Ø0.9--1.6mm V 6
0366 902 881 Bogey (HD) Fe, Ss & cored Ø1.4--2.4mm V
2
0366 902 894 Bogey Fe, Ss & cored Ø1.2mm V .045 / 7
0366 902 882 Bogey (HD)(S) Cored Ø1.2--2.0mm V--Knurled 3
0366 902 883 Bogey (HD) Cored Ø2.4mm V--Knurled 4
0366 902 899 Bogey Al Ø1.0--1.6mm U U4
0366 902 886 Bogey (HD) Al Ø1.2mmx3 U --
Item Ordering no. Denomination Wire type Wire dimensions
HK8 0366 944 001 W asher
HK9 0156 603 001
0156 603 002
0332 322 001
0332 322 002
Intermediate nozzle (S)
Intermediate nozzle
Intermediate nozzle
Intermediate nozzle
Fe, Ss & Al
Fe, Ss & Al
Cored
Cored
Ø 2 mm plastic for 0.6--1.6 mm
Ø 4 mm plastic for 2.0--2.4 mm
Ø 2.4 mm copper for 1.2--2.0 mm
Ø 4 mm copper for 2.4 mm
Item Ordering no. Denomination Note
HK10 0215 702 708 Locking washer
HK11 Nut M10
HK12 0458 748 002 Insulating washer
HK13 0458 748 001 Insulating bushing
Item Ordering no. Denomination Wire type Wire dimensions
HK14 0156 602 001
0156 602 002
0332 318 001
0332 318 002
Inlet nozzle (S)
Inlet nozzle
Inlet nozzle (HD)
Inlet nozzle (HD)
Fe, Ss, Al & Cored
Fe, Ss, Al & Cored
Fe, Ss & Cored
Fe, Ss & Cored
Ø 2 mm plastic for 0.6--1.6 mm
Ø 4 mm plastic for 2.0--2.4 mm
Ø 2.4 mm steel for 1.2--2.0 mm
Ø 4 mm steel for 2.4 mm
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
ESAB Feed 30-4 M14, Feed 48-4 M14 User manual
- Category
- Welding System
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB Feed 302 M11 User manual
-
ESAB Origo™ Feed 484 M13 User manual
-
ESAB ESABFeed 48-4 M14 User manual
-
ESAB Feed 304 M12 User manual
-
-
-
-
-
-
