Legrand Multi-Voltage Power Distribution Module, IS-0363 Installation guide

Legrand
Brand
Legrand
Model
Multi-Voltage Power Distribution Module, IS-0363
Type
Installation guide

Legrand Multi-Voltage Power Distribution Module, IS-0363, allows you to power a wide variety of modules and devices. It features multiple voltage distribution options: 12 volts DC to two locations, 15 volts DC to four locations, and 5 volts DC to one location. The module is overcurrent protected with an automatically resetting polyswitch device and includes a main power indicator LED and an overcurrent LED. It comes with a single bay bracket for mounting in On-Q style enclosure and six 24" power cord jumpers. To provide the specified voltage and maximum total power, the module must be connected to two power supplies (P/N PW7715), which are sold separately. The maximum total current is 2.9 Amps; 1 Amp maximum per port.

Legrand Multi-Voltage Power Distribution Module, IS-0363, allows you to power a wide variety of modules and devices. It features multiple voltage distribution options: 12 volts DC to two locations, 15 volts DC to four locations, and 5 volts DC to one location. The module is overcurrent protected with an automatically resetting polyswitch device and includes a main power indicator LED and an overcurrent LED. It comes with a single bay bracket for mounting in On-Q style enclosure and six 24" power cord jumpers. To provide the specified voltage and maximum total power, the module must be connected to two power supplies (P/N PW7715), which are sold separately. The maximum total current is 2.9 Amps; 1 Amp maximum per port.

INSTRUCTION / INSTALLATION SHEET
Multi-Voltage Power Distribution Module
IS-0363 Rev. O
301 Fulling Mill Road, Suite G
Middletown, PA 17057
Phone (800) 321-2343 / Fax (717) 702-2546
www.onqlegrand.com
©Copyright 2006 by On-Q/Legrand All Rights Reserved. Page 1 of 1
Figure 2
Figure 3
Figure 1
1. INTRODUCTION
The On-Q/Legrand Multi-Voltage Power Distribution Module (P/N PW7639) (see Figure 1) allows you
to power a wide variety of modules and devices.
2. FEATURES
• Allows you to power a wide variety of modules and devices
• The Multi-Voltage Power Distribution Module distributes:
– 15 volts DC to up to four locations (3 front / 1 rear)
– 12 volts DC to up to two locations
– 5 volts DC to one location
• Includes single bay bracket (P/N 364890-01) for mounting in On-Q style enclosure (see Figure 2)
• Includes six 24" power cord jumpers
• Overcurrent protected with an automatically resetting polyswitch device
• Main power indicator LED
• Overcurrent LED
3. POWER REQUIREMENTS
Power to the module is supplied by up to two 15V, 1.45A power supplies (P/N PW7715) that must
be purchased separately.
NOTE: To provide the specified voltage and the maximum total power,
the module must be connected to two power supplies.
NOTE: Using two supplies, the max total current is 2.9Amp; 1Amp Max per port.
If the max total current exceeded, the red "Overcurrent" LED will illuminate and
DC Output power cannot be guaranteed.
4. INSTALLATION
Refer to the example shown in Figure 3 during
installation.
A. Snap the Power Distribution Module onto the
included bracket using the push-pins at each
corner.
B. Plug the cord from the first power supplies into
the socket labelled "IN 1"; if using a second
power supply, plug its cord into the socket
labelled "IN2".
C. Without mounting the module, find the
appropriate spot in the enclosure where all the
power cord jumpers reach the modules to be
powered.
D. Mount the module/bracket into the enclosure,
insert the tabs on the left side of the bracket into
the slots in the enclosure and push the bracket
pushpin into an appropriate hole in the enclosure
to secure the module/bracket to the enclosure.
E. Make the appropriate connections with the power
cord jumpers.
F. Plug the power supplies into the AC Input
receptical(s).
  • Page 1 1

Legrand Multi-Voltage Power Distribution Module, IS-0363 Installation guide

Legrand
Brand
Legrand
Model
Multi-Voltage Power Distribution Module, IS-0363
Type
Installation guide

Legrand Multi-Voltage Power Distribution Module, IS-0363, allows you to power a wide variety of modules and devices. It features multiple voltage distribution options: 12 volts DC to two locations, 15 volts DC to four locations, and 5 volts DC to one location. The module is overcurrent protected with an automatically resetting polyswitch device and includes a main power indicator LED and an overcurrent LED. It comes with a single bay bracket for mounting in On-Q style enclosure and six 24" power cord jumpers. To provide the specified voltage and maximum total power, the module must be connected to two power supplies (P/N PW7715), which are sold separately. The maximum total current is 2.9 Amps; 1 Amp maximum per port.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents