• NanoPave Hardscaoe Sealer (NPHS) is a color enhancing
sealant recommended for use on hardscape walkways, patios,
and other foot traffic areas. It is not recommended for
vehicular traffic applications.
• NPHS should be installed within an ambient and surface
temperature range of 40°-90°F. Shaded, low sunlight, or colder
areas will lengthen cure times. Conversely, direct sun, warmer
areas will shorten cure times. Avoid temperatures at or below
freezing or above 100°F for NPHS curing phase or storage.
• NPHS is a water-based formulation. The curing phase is
dependent upon complete evaporation of the water
component (usually 6-12 hours in optimal conditions).
• To increase sheen to desired aesthetic, additional coats of
NPHS may be applied at twice the initial application rate, once
cured. Additional coats may darken surface.
• Coverage rate is dependent on hardscape surface and
porosity. See Coverage Chart for more information or visit
TechniSoil.com.
I
N
S
T
A
L
L
A
T
I
O
N
G
U
I
D
E
Visit TechniSoil.com for more information
TOP 5 TIPS
README.TXT
• ALWAYS PERFORM A TEST SECTION USING RECOMMENDED
INSTALLATION METHODS TO CONFIRM SUITABILITY OF
MATERIALS AND PROJECT CONDITIONS!
• NanoPave Hardscape Sealer (NPHS) may be installed on
damp surfaces. Avoid excessively wet conditions or standing
water. Do not install NPHS within 24-48 hours before or
after rainfall.
• Hardscape surface must be clean, dry, and free of debris.
• Remove or treat any stains, efflorescence, or existing
sealants using appropriate cleaning agents prior to NPHS
application.
• Indoor applications require adequate ventilation.
• Mask or shield any adjacent surfaces in case of overspray.
• Applying additional coats of NPHS can cause some
hardscape surfaces to become slippery in wet conditions.
• During application, avoid foaming sealer. If foaming
occurs, distribute the liquid evenly before curing using a
squeegee.
• Keep project area free from any moisture or foot traffic
until fully cured (6-12 hours in optimal conditions).
• Clean all tools immediately after use with a soft bristle
brush and rinse with water.
APPLICATION
RATE RANGE:
SURFACE
AESTHETIC:
Broomed or Stamped Concrete
Bricks / Flagstone
100 - 150 ft
2
/gal
Pavers / Natural Stone
150 - 200 ft
2
/gal
Smooth Concrete
200 - 250 ft
2
/gal
Apply NPHS to concrete surface using a low
pressure sprayer (40 PSI), and evenly apply over
entire surface using the recommended coverage
rate.
01
APPLY NP HARDSCAPE SEALER
SQUEEGEE SURFACE
Distribute NPHS with a foam rubber squeegee
or sponge.
02
Pavers Natural Stone
Stamped Concrete
NANOPAVE
WARRANTY: TechniSoil Global, Inc. warrants this product to be free from defects. Where permitted by law, TechniSoil makes no other
warranties with respect to this product, express or implied, including without limitation the implied warranties of merchantability or fitness
for particular purpose. The purchaser shall be responsible to orchestrate their own tests to determine the suitability of this product for their
particular purpose. TechniSoil’s liability shall be limited in all events to supplying sufficient product to re-treat the specific areas to which
product proven to be defective has been applied. Acceptance and use of this product absolves TechniSoil from any other liability, from any
and all sources, including liability for incidental, consequential or resultant damages whether due to breach of warranty, negligence or strict
liability. This warranty may not be modified or extended by representatives of TechniSoil, its distributors or dealers, independent contractors,
clients or end-users of any kind. ALWAYS TEST FIRST. Before Handling or using this product, PLEASE SEE Material Data Sheet (MSDS). IN CASE
OF CHEMICAL EMERGENCY: For Spill, Leak, Fire Exposure or Accident Call: 1.800.424.9300 (Domestic North America)
CONTACT US
TechniSoil Global, Inc.
877-356-2250
TechniSoil.com
HARDSCAPE SEALER
™
/
