2. Leon
  3. TrLS50 Spike
TrLS50 Spike

Leon TrLS50 Spike User manual

  • Hello! I've reviewed the user manual for the Leon TERRA LS50 series speakers, including models TrLS50-Spike, TrLS50-Hardscape, TrLS50-Inground, and TrLS50-Bollard. This document provides detailed installation instructions, safety precautions, and information on various mounting options. I'm ready to answer any questions you have about these speakers or their installation process.
  • What should I do before starting the installation?
    How do I connect the wires using the provided connectors?
    Where is the tap switch for the 70v transformer located?
REF-25-047_TrLS50_Bollard_20220325
INCLUDED HARDWARE
PAGE 1
For assistance call (888) 213-5015 or visit www.leonspeakers.com
TrLS50-Spike / TrLS50-Hardscape
TrLS50-Inground / TrLS50-Bollard
TERRA LS50
TrLS50 - Spike
TrLS50 - Hardscape
TrLS50 - Inground TrLS50 - Bollard
2X/4
100V
8 Ohm
SELECT INPUT
16W
32W
64W
64W
32W
16W
8W
70V
Fig. A
Cable Routing
To utilize the provided waterproof connectors, strip each
conductor ½”. Insert each bare wire into a hole of the connector.
Press down on the top ‘button’ until a click is heard and the wires
are secure.
Fig. B
Setting the 70v Transformer
Set the 70v transformer tap wattage prior to installation. The tap
switch is located on the bottom of the speaker and can be turned
with a small flathead screwdriver.
INSTALLATION TIPS
Choose an installation location free of physical obstructions behind or within the wall.
Working near electrical equipment and wires poses an electrocution hazard. Turn off nearby electrical circuits from the breaker. Use a non-contact voltage tester to
confirm that the installation location is free of live electrical wires and equipment prior to cutting or drilling into the wall. Contact a qualified electrician before making
any modifications to electrical wiring.
Determine the potential hazards of working with hand or power tools and take the appropriate safety precautions. Use personal protective equipment (PPE) as appropriate,
including, but not limited to: vision, hearing, and respiratory protection.
Consult local building and/or electrical codes prior to installation of speakers, cabling, or electrical equipment.
Cleaning- use a soft brush such as one for auto or boat care to brush off any materials (dirt or grass).
Grille care - Please be careful and avoid contact with the grille during lawn care such as mowing or weed wacking to prevent damage to the grille.
B
2X/4X
Connector
C
1X
Hardscape
Pan
E
1X
Burial Plate
D
3X
1/4”-20 x 3/4”
Screw
TrLS50 - Inground
H
3X
12” Rod
G
6X
1-4”-20 Nut
F
6X
1-4”-20
Washer
TrLS50 - Bollard
B
X
Connector
K
1X
Bollard Tube
L
1X
Bollard TrLS50
I
1X
Bollard
Pan
J
6X
1/4”-20 x 3/4”
Flathead Screw
TrLS50 - Hardscape
C
1X
Hardscape
Pan
D
3X
1/4”-20 x 3/4”
Screw
B
2X/4X
Connector
B
2X/4X
Connector
A
2X
Spike
TrLS50 - Spike
Drawings not to scale
*All -Halo and -Bollard models include 2 additional connectors.
Instructions included with Bollard Mount
For assistance call (888) 213-5015 or visit www.leonspeakers.com
PAGE 2
Fig. 6
Fig. 5
Completing
the Installation
For TrLS50-Spike, hide the connectors under the speaker and press the spikes into
the ground. For TrLS50-Hardscape or -Inground, tuck the connectors between the
speaker and hardscape pan and attach the speaker using three
button head screws .
OR
D
Fig. 4
Making the Connection
If necessary, trim excess cable both on the speaker and input side. Strip the
individual wires and use the waterproof connectors to connect the speaker and
lighting (if a -Halo model), and daisy-chain to the next speaker (if applicable).
B
Fig. 3d
Pull any wiring through the center hole of the hardscape pan and bury the unit in the
ground, backfilling with material until only the hardscape pan is above the surface.
Fig. 3c
Place the hardscape pan onto the threaded rods and secure it with three nuts
and three washers . Tighten hardware.
C
GF
Fig. 3b
Thread one nut onto each threaded rod until the distance between the nuts and
the burial plate is 10 3/8”.
10 3/8”
X3
G
Fig. 3a
Burial Mounting with Inground
For burial mounting with TrLS50-Inground, begin by assembling the burial
hardware. Screw the three threaded rods into the burial plate .
HE
Fig. 2
Hardscape Mounting
For hard surface mounting with TrLS50-Hardscape, install the hardscape
pan with appropriate anchors for the substrate. Speaker wires must be pulled
through the center hole prior to installation. Any of the three mounting holes can be
designated as the front of the speaker. Proceed to figure 4.
Top View
Front
C
A
Fig. 1
Ground Mounting With Spike
For ground mounting with TrLS50-Spike, screw the spikes into the bottom of the
TrLS50. Proceed to figure 4.
Fig. 1
Complete the Installation
Now you’re ready to enjoy your favorite music outdoors.
Fig. 4
Mounting the Speaker
Position the TrLS50 speaker on top of the bollard tube and mount the speaker
to the bollard tube using the remaining 1/4-20 flathead screws .
L K
J
Fig. 3
Making the Connection
If necessary, trim excess cable both on the speaker and input side. Strip the
individual wires and use the waterproof connectors to connect the speaker and
halo lighting. Use an additional connector for path lighting (if applicable). Daisy
chain to the next speaker (if applicable). Test your connection now.
B
Fig. 2
Bollard Tube Mounting
Fasten the bollard tube to the bollard pan using 3 of the provided 1/4-20
flathead screws . Allow speaker wires to rest in the tube for now.
IK
J
Fig. 1
Ground Mounting With Spike
Screw the bollard pan to your hard surface with apropriate anchors for
the substrate. Speaker wires must be pulled through the center hole prior to
installation.
Front
Top View
I
For assistance call (888) 213-5015 or visit www.leonspeakers.com
PAGE 3
/