WEG SSW7000 Programming Manual

Motors | Automation | Energy | Transmission & Distribution | Coatings

Soft-Starter

SSW7000

Programming Manual

Series: SSW7000

Language: English

Document: 10001038255 / 07

Software Version: 1.7X

Publication date: 03/2019

Revision Description Chapter

01 First edition -

02

V1.20 new functions:

Voltage Ramp + Current Limit

Direct on Line D.O.L.

Safe Sectioning Mode

F064 and F145 protections

70A current model

-

03

V1.30 new functions:

SSW7000C Current models

New function for digital outputs – Capacitor

-

04 V1.40. New option for language, P0201 = 4 (French) -

05

New functions V1.50:

Option 16 – Blocking PFC – for DI1 to DI6

Option 14 – The description of Capacitor for Control PFC was changed – for DO1 to DO3

Option 15 – Blocking PFC Output – for DO1 to DO3

Fault 126 – IOE-04 Access Error

06

New functions V1.60

New parameter to discharge the PFC – P0280

D.O.L operation was changed

07 13800 V voltage model

Contents .

SSW7000 | 5

CONTENTS

1. QUICK PARAMETER REFERENCE ................................................. 10

2. FAULTS AND ALARMS ........................................................................ 28

3. SAFETY NOTICES ............................................................................. 35

3.1. SAFETY NOTICES IN THIS MANUAL .......................................................................................... 35

3.2. SAFETY NOTICES ON THE PRODUCT ....................................................................................... 35

3.3. PRELIMINARY RECOMMENDATIONS ....................................................................................... 36

4. ABOUT THIS MANUAL ..................................................................... 37

4.1. TERMINOLOGY AND DEFINITIONS............................................................................................ 37

4.1.1. Terms and Definitions Used in the Manual ......................................................................... 37

4.1.2. Numerical Representation ................................................................................................. 38

4.1.3. Symbols for the Parameter Properties Description ............................................................. 38

5. SOFTWARE VERSION ....................................................................... 39

6. ABOUT THE SSW7000 SOFT-STARTER ......................................... 40

7. HMI ...................................................................................................... 42

8. PROGRAMMING BASIC INSTRUCTIONS ...................................... 43

8.1. PARAMETER STRUCTURE ......................................................................................................... 43

8.2. PASSWORD SETTING IN P0000 .................................................................................................. 44

8.3. HMI [20] ......................................................................................................................................... 44

8.4. DATE AND TIME SETTING ........................................................................................................... 48

8.5. SETTING OF THE DISPLAY INDICATIONS IN THE MONITORING MODE .............................. 48

8.6. IMCOMPATIBILITY BETEWEEN PARAMETERS ....................................................................... 51

8.7. CHANGED PARAMETERS [03] .................................................................................................... 51

9. BACKUP PARAMETERS [04] ........................................................... 52

10. I/O CONFIGURATION [05] ............................................................. 56

10.1. LOCAL/REMOTE CONFIGURATION [21] ................................................................................... 56

10.2. ANALOG INPUTS [23] .................................................................................................................. 58

10.3. ANALOG OUTPUTS [24] .............................................................................................................. 60

10.4. DIGITAL INPUTS [25] ................................................................................................................... 62

10.5. DIGITAL OUTPUTS [26] ............................................................................................................... 65

11. CONTROL TYPE [22] ...................................................................... 68

12. SSW DATA [27] ............................................................................... 81

13. MOTOR DATA [28] .......................................................................... 84

14. SPECIAL FUNCTIONS .................................................................... 86

14.1. ORIENTED START-UP [02] .......................................................................................................... 86

14.2. TEST MODE [09] ........................................................................................................................... 87

14.3. SAFE SECTIONG [10] ................................................................................................................... 88

14.4. BRAKING [29] ............................................................................................................................... 89

14.5. JOG [30] ......................................................................................................................................... 92

14.6. KICK START [31] .......................................................................................................................... 94

15. PROTECTIONS [32] ........................................................................ 96

15.1. VOLTAGE PROTECTIONS [110] .................................................................................................. 96

15.2. CURRENT PROTECTIONS [111] ................................................................................................. 98

Contents .

6 | SSW7000

15.3. GROUND FAULT PROTECTIONS [112] ................................................................................... 102

15.4. PHASE SEQUENCE [113] .......................................................................................................... 103

15.5. MOTOR THERMAL PROTECTION [114] .................................................................................. 104

15.6. MOTOR THERMAL CLASS PROTECTION [115] ..................................................................... 107

15.7. TORQUE PROTECTIONS [116] ................................................................................................. 116

15.8. POWER PROTECTIONS [117] ................................................................................................... 118

15.9. TIMER PROTECTIONS [118] ..................................................................................................... 119

16. READ ONLY PARAMETERS [08] ................................................. 122

16.1. READ ONLY PARAMETERS ...................................................................................................... 122

16.2. FAULT HISTORY [06] ................................................................................................................. 129

16.3. DIAGNOSTICS [07] .................................................................................................................... 133

17. COMMUNICATION [33] ................................................................ 139

17.1. RS-232 AND RS-485 SERIAL INTERFACE [131] ..................................................................... 139

17.2. ANYBUS-CC INTERFACE [132] ................................................................................................ 139

17.3. COMMUNICATION STATUS AND COMMANDS [130] ............................................................ 140

17.4. LOCAL/REMOTE CONFIGURATION [133] .............................................................................. 140

18. SOFTPLC [34] ................................................................................ 141

19. TRACE FUNCTION [35] ................................................................ 142

20. PROGRAMMING INFORMATION AND SUGGESTIONS ........... 147

20.1. APPLICATIONS AND PROGRAMMING ................................................................................... 147

20.2. STARTING WITH VOLTAGE RAMP + CURRENT LIMIT (P0202 = 0) ...................................... 149

20.3. STARTING WITH CURRENT LIMIT (P0202 = 1) ....................................................................... 149

20.4. STARTING WITH CURRENT RAMP AND HIGHER INITIAL VALUE (P0202 = 4) ................... 150

20.5. STARTING WITH CURRENT RAMP AND LOWER INITIAL VALUE (P0202 = 4) .................... 152

20.6. STARTING WITH PUMP CONTROL (P0202 = 2) ...................................................................... 152

20.6.1. Constant Torque Loads (P0202 = 3 and P0120 = 1 point) ........................................... 154

20.6.2. Loads with Higher Initial Torque (P0202 = 3 and P0120 = 3 points) ............................. 154

20.6.3. Constant Torque Loads with S Speed Curve (P0202 = 3 and P0120 = 3 points) .......... 155

20.6.4. Quadratic Torque Loads with S Speed Curve (P0202 = 3 and P0120 = 2 points) ......... 155

20.6.5. Quadratic Torque Loads with Linear Speed Curve (P0202 = 3 and P0120 = 3 points) .. 156

20.6.6. Quadratic Loads with Higher Initial Torque (P0202 = 3 and P0120 = 3 points) ............. 156

20.6.7. Hydraulic Pump Type Loads (P0202 = 3) .................................................................... 157

20.7. UNDER- AND OVER- PROTECTIONS ...................................................................................... 160

20.7.1. Undervoltage and Overvoltage Protections .................................................................. 160

20.7.2. Underload Protection .................................................................................................. 160

20.7.3. Overload Protection .................................................................................................... 161

Index .

SSW7000 | 7

FIGURE INDEX

Figure 6.1: SSW simplified block diagram .......................................................................................................... 41

Figure 7.1: HMI keys .......................................................................................................................................... 42

Figure 8.1: Sequence for parameter modification permission through P0000 .................................................... 44

Figure 8.2: Date and time setting ....................................................................................................................... 48

Figure 8.3: Monitoring mode screen with the factory settings ............................................................................ 49

Figure 8.4: Monitoring mode screen with bar graphs ......................................................................................... 49

Figure 8.5: Configuration of bar graph mode monitoring .................................................................................... 50

Figure 8.6: Example of a monitoring mode screen with P0205 programmed for bigger characters .................... 50

Figure 9.1: Parameter transfer ........................................................................................................................... 52

Figure 9.2: Parameter copy from “SSW A” to “SSW B” ..................................................................................... 55

Figure 10.1: Motor rotation direction change via contactors .............................................................................. 57

Figure 10.2: Motor rotation direction change only with JOG .............................................................................. 57

Figure 10.3: Analog input block diagram ........................................................................................................... 59

Figure 10.4: Analog output block diagram ......................................................................................................... 61

Figure 10.5: Details on the Load User 1/2 function operation ............................................................................ 64

Figure 11.1: Programming sequence of the control types .................................................................................. 71

Figure 11.2: Initial Voltage .................................................................................................................................. 72

Figure 11.3: Acceleration ramp by Voltage Ramp .............................................................................................. 73

Figure 11.4: Acceleration ramp by Current Limit ................................................................................................ 73

Figure 11.5: Deceleration ramp by voltage ......................................................................................................... 74

Figure 11.6: Current Limit .................................................................................................................................. 75

Figure 11.7: Starting with current ramp and lower initial value ............................................................................ 76

Figure 11.8: Starting with current ramp and higher initial value .......................................................................... 76

Figure 11.9: Available starting torque profiles ..................................................................................................... 77

Figure 11.10: Available stopping torque profiles................................................................................................. 79

Figure 11.11: Start and Stop by Pump Control .................................................................................................. 80

Figure 14.1: Oriented start-up programming sequence ..................................................................................... 86

Figure 14.2: Braking torque ............................................................................................................................... 89

Figure 14.3: Reverse braking ............................................................................................................................. 90

Figure 14.4: Optimal braking.............................................................................................................................. 90

Figure 14.5: DC braking ..................................................................................................................................... 91

Figure 14.6: Starting torque pulse - kick start - settings ..................................................................................... 95

Figure 15.1: Over- and Undervoltage trip levels ................................................................................................. 97

Figure 15.2: Over- and Undercurrent trip levels ............................................................................................... 100

Figure 15.3: Ground fault detection by current ................................................................................................. 103

Figure 15.4: Ground fault detection by voltage ................................................................................................ 103

Figure 15.5: Motor Thermal Class Protection programming sequence ............................................................. 109

Figure 15.6: Standard motor thermal classes .................................................................................................. 112

Figure 15.7: Motor temperature regions within the insulation class .................................................................. 113

Figure 15.8: Motor heating .............................................................................................................................. 114

Figure 15.9: Motor heating constant for the nominal current ............................................................................ 115

Figure 15.10: Deenergized motor cooling constant .......................................................................................... 116

Figure 15.11: Motor thermal memory reset ...................................................................................................... 116

Figure 15.12: Over- and Undertorque trip levels .............................................................................................. 118

Figure 15.13: Operation via HMI ...................................................................................................................... 120

Figure 15.14: Operation via three-wire digital inputs (DI1 and DI2) ................................................................... 120

Figure 15.15: Operation via digital input (DI1) ................................................................................................... 121

Figure 18.1: Example of a SoftPLC applicative in the WLP programming software .......................................... 141

Figure 20.1: Torque and current characteristic curves of a direct on line start and of a Voltage Ramp start ..... 147

Figure 20.2: Torque and current characteristic curves of a Current Limit start and of a Torque Control start ... 147

Figure 20.3: Starting with voltage ramp ........................................................................................................... 149

Figure 20.4: Starting with current limit .............................................................................................................. 150

Figure 20.5: Starting with current ramp and higher initial value ........................................................................ 150

Figure 20.6: Starting with current ramp and lower initial value .......................................................................... 152

Figure 20.7: Centrifugal hydraulic pump rotation direction ............................................................................... 153

Figure 20.8: Manometer showing the pressure increase .................................................................................. 153

Figure 20.9: Manometer showing the pressure drop........................................................................................ 153

Figure 20.10: Starting with pump control ......................................................................................................... 154

Index .

8 | SSW7000

Figure 20.11: Starting with constant torque control - 1 point .......................................................................... 154

Figure 20.12: Starting with quadratic torque control, 3 points, higher initial load ............................................. 155

Figure 20.13: Starting with quadratic torque control, 3 points, constant load .................................................. 155

Figure 20.14: Starting with linear torque control, 2 points, quadratic load ....................................................... 156

Figure 20.15: Starting with quadratic torque control, 3 points, quadratic load ................................................. 156

Figure 20.16: Starting with quadratic torque control, 3 points, quadratic load with higher initial torque ........... 157

Figure 20.17: Manometer showing pressure rise with linear torque ................................................................. 157

Figure 20.18: Manometer showing pressure rise with quadratic torque .......................................................... 158

Figure 20.19: Hydraulic pump stopping with constant torque, 1 point ............................................................ 158

Figure 20.20: Hydraulic pump stopping with linear torque, 2 points ................................................................ 159

Figure 20.21: Hydraulic pump stopping with quadratic torque, 3 points ......................................................... 159

Figure 20.22: Manometer showing pressure fall with torque control ................................................................ 159

Index .

SSW7000 | 9

TABLE INDEX

Table 8.1: SSW parameter groups structure ...................................................................................................... 43

Table 8.2: P0200 options .................................................................................................................................. 46

Table 9.1: P0204 options .................................................................................................................................. 52

Table 9.2: P0318 options .................................................................................................................................. 53

Table 9.3: P0319 options .................................................................................................................................. 54

Table 10.1: DIP Switches related to the analog inputs ....................................................................................... 60

Table 10.2: Configuration of the analog input signals ......................................................................................... 60

Table 10.3: - Full scale ....................................................................................................................................... 61

Table 10.4: DIP Switches related to the analog outputs ..................................................................................... 62

Table 10.5: Configuration of the analog output signals ...................................................................................... 62

Table 10.6: Digital input status ........................................................................................................................... 63

Table 10.7: Digital output status ........................................................................................................................ 65

Table 11.1: Available deceleration methods as a function of the starting technique ........................................... 70

Table 11.2: P0121 function according to P0120................................................................................................ 77

Table 11.3: P0122 function according to P0120................................................................................................ 78

Table 11.4: P0123 function according to P0120................................................................................................ 78

Table 11.5: P0124 function according to P0120................................................................................................ 78

Table 11.6: P0126 function according to P0125................................................................................................ 79

Table 11.7: P0127 function according to P0125................................................................................................ 80

Table 11.8: P0128 function according to P0125................................................................................................ 80

Table 12.1: SSW accessory identification code ................................................................................................. 82

Table 12.2: Formation of the two first codes for P0028 ..................................................................................... 82

Table 12.3: Module types .................................................................................................................................. 82

Table 14.1: Jog and motor rotation direction ..................................................................................................... 93

Table 15.1: Ground fault protection tripping mode .......................................................................................... 102

Table 16.1: SSW status description ................................................................................................................. 123

Table 19.1: Full scale of the variables selectable as trigger .............................................................................. 142

Table 19.2: Description of P0552 options ........................................................................................................ 143

Table 20.1: Typical staring torque characteristic curves of some loads, with suggested control types ............. 148

Quick Parameter Reference .

10 | SSW7000

1. QUICK PARAMETER REFERENCE

Software: V1.6X

Application:

Model:

Serial number:

Responsible:

Date: / /

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0000

Access to Parameters

0 to 9999

0

20

44

P0001

SSW Current

0.0 to 999.9 %

ro

08

122

P0002

Motor Current (%)

0.0 to 999.9 %

ro

08

122

P0003

Motor Current (A)

0.0 to 6553.5 A

ro

08

122

P0004

Main Line Voltage

0 to 65535 V

ro

08

122

P0005

Main Line Frequency

0.0 to 99.9 Hz

ro

08

123

P0006

SSW Status

0 = Ready

ro

08

123

1 = Initial Test

2 = Fault

3 = Ramp Up

4 = Full Voltage

5 = Bypass

6 = Not Used

7 = Ramp Down

8 = Braking

9 = FWD/REV

10 = Jog

11 = Delay P831

12 = General Disab.

13 = Configuration

14 = Direct on Line D.O.L.

P0007

Output Voltage

0 to 65535 V

ro

08

124

P0008

Power Factor

0.00 to 1.00

ro

08

124

P0009

Motor Torque

0.0 to 999.9 %

ro

08

124

P0010

Output Power

0 to 65535 kW

ro

08

125

P0011

Output Apparent Power

0 to 65535 kVA

ro

08

125

P0012

DI6 to DI1 Status

0000h to 003Fh

ro

08, 25

125

P0013

DO3 to DO1 Status

0000h to 0007h

ro

08, 26

125

P0014

AO1 Value

0.00 to 100.00 %

ro

08, 24

125

P0015

AO2 Value

0.00 to 100.00 %

ro

08, 24

125

P0018

AI1 Value

-100.00 to 100.00 %

ro

08, 23

125

P0019

AI2 Value

-100.00 to 100.00 %

ro

08, 23

126

P0020

Present Fault

0 to 999

ro

08

126

P0021

Present Alarm

0 to 999

ro

08

126

P0023

C1 Software Version

0.00 to 655.35

ro

08, 27

81

P0027

Accessories Config. 1

0000h to FFFFh

ro

08, 27

81

P0028

Accessories Config. 2

0000h to FFFFh

ro

08, 27

81

P0029

Phase Sequence

0 = Invalid

ro

08

126

1 = RST / 123

2 = RTS / 132

P0030

R Phase Current

0.0 to 6553.5 A

ro

08

126

P0031

S Phase Current

0.0 to 6553.5 A

ro

08

126

P0032

T Phase Current

0.0 to 6553.5 A

ro

08

126

P0033

R-S Main Line Voltage

0 to 65535 V

ro

08

127

Quick Parameter Reference .

SSW7000 | 11

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0034

S-T Main Line Voltage

0 to 65535 V

ro

08

127

P0035

T-R Main Line Voltage

0 to 65535 V

ro

08

127

P0042

Powered Time

0 to 65535 h

ro

07, 08

133

P0043

Enabled Time

0.0 to 6553.5 h

ro

07, 08

133

P0044

kWh Counter

0 to 999 kWh

ro

07, 08

134

P0045 MWh Counter 0 to 65535 MWh ro 07, 08 134

P0046

Enabled Fan Time

0 to 65535 h

ro

07, 08

134

P0047

Maximum Start Curre.

0.0 to 6553.5 A

ro

07, 08

134

P0048

Average Start Curre.

0.0 to 6553.5 A

ro

07, 08

135

P0049

Real Start Time

0 to 999 s

ro

07, 08

135

P0050

Thermal Class Status

0.0 to 100.0 %

ro

07, 08

127

P0053

Max.Curr.Full Voltage

0.0 to 6553.5 A

ro

07, 08

135

P0054

Max. Voltage Motor ON

0 to 65535 V

ro

07, 08

135

P0055

Min. Voltage Motor ON

0 to 65535 V

ro

07, 08

136

P0056

Max.Frequenc.Motor ON

0.0 to 99.9 Hz

ro

07, 08

136

P0057

Min.Frequenc.Motor ON

0.0 to 99.9 Hz

ro

07, 08

136

P0058

Máx. Number Start/h

0 to 32 ph

ro

07, 08

136

P0059

Total Number Start

0 to 65535

ro

07, 08

137

P0060

R-U SCRs Temperature

-22 to 100 °C

ro

08

128

P0061

S-V SCRs Temperature

-22 to 100 °C

ro

08

128

P0062

T-W SCRs Temperature

-22 to 100 °C

ro

08

128

P0063

Ch1 Motor Temperature

-20 to 260 °C

ro

08

128

P0064

Ch2 Motor Temperature

-20 to 260 °C

ro

08

128

P0065

Ch3 Motor Temperature

-20 to 260 °C

ro

08

128

P0066

Ch4 Motor Temperature

-20 to 260 °C

ro

08

128

P0067

Ch5 Motor Temperature

-20 to 260 °C

ro

08

128

P0068

Ch6 Motor Temperature

-20 to 260 °C

ro

08

128

P0069

Ch7 Motor Temperature

-20 to 260 °C

ro

08

128

P0070

Ch8 Motor Temperature

-20 to 260 °C

ro

08

128

P0071

Ground Fault Current

0.00 to 9.99 A

ro

08

128

P0072

Ground Fault Voltage

0 to 65535 V

ro

08

129

P0073

Control 1 Voltage

0 to 999 V

ro

08

129

P0074

Control 2 Voltage

0.0 to 99.9 Vcc

ro

08

129

P0077

R-U SCRs Max. Temp.

-22 to 100 °C

ro

07, 08

137

P0078

S-V SCRs Max. Temp.

-22 to 100 °C

ro

07, 08

137

P0079

T-W SCRs Max. Temp.

-22 to 100 °C

ro

07, 08

137

P0080

Ch1 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0081

Ch2 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0082

Ch3 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0083

Ch4 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0084

Ch5 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0085 Ch6 Motor Max. Temp. -20 to 260 °C ro 07, 08 137

P0086

Ch7 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0087

Ch8 Motor Max. Temp.

-20 to 260 °C

ro

07, 08

137

P0099

C2 Software Version

0.00 to 655.35

ro

08, 27

81

P0101

Initial Start Voltage

35 to 90 %

40 %

22

72

P0102

Maximum Start Time

1 to 999 s

20 s

22

72

P0103

Step Down Volt. Stop

60 to 100 %

100 %

22

73

P0104

Stop Time

0 to 999 s

0 s

22

74

P0105

End Voltage Stop

35 to 55 %

35 %

22

74

P0106

Start End Detection

0 = Time (P0102)

1

22

74

1 = Automatic

P0110

Current Limit

150 to 600 %

300 %

22

75

Quick Parameter Reference .

12 | SSW7000

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0111

Initial Current Ramp

150 to 600 %

150 %

22

75

P0112

Current Ramp Time

1 to 99 %

20 %

22

76

P0120

Start Torque Chara.

1 = Constant

1

cfg

22

76

2 = Linear

3 = Square

P0121

Initial Start Torque

10 to 400 %

30 %

22

77

P0122

End Start Torque

10 to 400 %

110 %

22

77

P0123

Minimun Start Torque

10 to 400 %

27 %

22

78

P0124

Min.Start Torq. Time

1 to 99 %

20 %

22

78

P0125

Stop Torque Characte.

1 = Constant

1

cfg

22

78

2 = Linear

3 = Square

P0126

End Stop Torque

10 to 100 %

20 %

22

79

P0127

Minimum Stop Torque

10 to 100 %

50 %

22

79

P0128

Min. Stop Torque Time

1 to 99 %

50 %

22

80

P0130

Pump Control

0 to 0

0

cfg

80

P0193

Day of the Week

0 = Sunday

00

20

44

1 = Monday

2 = Tuesday

3 = Wednesday

4 = Thursday

5 = Friday

6 = Saturday

P0194

Day

01 to 31

01

20

45

P0195

Month

01 to 12

01

20

45

P0196

Year

00 to 99

06

20

45

P0197

Hour

00 to 23

00

20

45

P0198

Minutes

00 to 59

00

20

45

P0199

Seconds

00 to 59

00

20

45

P0200

Password

0 = Off

1

20

45

1 = On

2 = Change Pass.

P0201

Language

0 = Português

1

20

46

1 = English

2 = Español

3 = Deutsch

4 = Français

P0202

Types of Control

0 = Voltage Ramp + C. Lim.

0

cfg

22

68

1 = Current Limit

2 = Pump Control

3 = Torque Control

4 = Current Ramp

5 = Direct on Line D.O.L.

P0203

Fan Configuration

0 = Always Off

2

cfg

27

82

1 = Always On

2 = Controlled

P0204

Load/Save Parameters

0 = Not Used

0

cfg

04

52

1 = Not Used

2 = Not Used

3 = P0043..P0050=0

4 = P0053..P0058=0

5 = Ld.Default

6 = P0077..P0087=0

7 = Load User 1

Quick Parameter Reference .

SSW7000 | 13

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

8 = Load User 2

9 = Load User 3

10 = Save User 1

11 = Save User 2

12 = Save User 3

P0205 Read Parameter Sel. 1 0 = Not selected 2 20 46

1 = SSW Current #

2 = Motor Curr.% #

3 = Motor Curr.A #

4 = Line Voltage #

5 = Output Volt. #

6 = Power Factor #

7 = Motor Torque #

8 = Output Power #

9 = ReactivePower#

10 = R Phase Curr.#

11 = S Phase Curr.#

12 = T Phase Curr.#

13 = RS Line Volt.#

14 = ST Line Volt.#

15 = TR Line Volt.#

16 = RU SCR Temper.#

17 = SV SCR Temper.#

18 = TW SCR Temper.#

19 = Ch1 Mot.Tempe.#

20 = Ch2 Mot.Tempe.#

21 = Ch3 Mot.Tempe.#

22 = Ch4 Mot.Tempe.#

23 = Ch5 Mot.Tempe.#

24 = Ch6 Mot.Tempe.#

25 = Ch7 Mot.Tempe.#

26 = Ch8 Mot.Tempe.#

27 = Ther.Clas.Sta#

28 = SSW Current -

29 = Motor Curr.% -

30 = Motor Curr.A -

31 = Line Voltage -

32 = Output Volt. -

33 = Power Factor -

34 = Motor Torque -

35 = Output Power -

36 = ReactivePower-

37 = R Phase Curr.-

38 = S Phase Curr.-

39 = T Phase Curr.-

40 = RS Line Volt.-

41 = ST Line Volt.-

42 = TR Line Volt.-

43 = RU SCR Temper.-

44 = SV SCR Temper.-

45 = TW SCR Temper.-

46 = Ch1 Mot.Tempe.-

47 = Ch2 Mot.Tempe.-

Quick Parameter Reference .

14 | SSW7000

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

48 = Ch3 Mot.Tempe.-

49 = Ch4 Mot.Tempe.-

50 = Ch5 Mot.Tempe.-

51 = Ch6 Mot.Tempe.-

52 = Ch7 Mot.Tempe.-

53 = Ch8 Mot.Tempe.-

54 = Ther.Clas.Sta-

P0206

Read Parameter Sel. 2

See options in P0205

4

20

46

P0207

Read Parameter Sel. 3

See options in P0205

5

20

46

P0208

Auto-Reset Time

0 to 600 s

0 s

118

119

P0213

Read Par.1 Full Scale

0.0 to 600.0 %

100.0 %

cfg

20

47

P0214

Read Par.2 Full Scale

0.0 to 600.0 %

100.0 %

cfg

20

47

P0215

Read Par.3 Full Scale

0.0 to 600.0 %

100.0 %

cfg

20

47

P0216

LCD Contrast

0 to 37

27

20

48

P0220

LOC/REM Mode Selection

0 = Always LOC

3

cfg

21

56

1 = Always REM

2 = HMI LR Key LOC

3 = HMI LR Key REM

4 = DIx

5 = Serial/USB LOC

6 = Serial/USB REM

7 = Anybus-CC LOC

8 = Anybus-CC REM

9 = SoftPLC LOC

10 = SoftPLC REM

P0228

FWD/REV Selection

0 = Inactive

0

21, 30

56

1 = By Contactor

2 = Only for JOG

P0229

LOC Command Selection

0 = I,O Keys

0

cfg

21

57

1 = DIx

2 = Serial/USB

3 = Anybus-CC

4 = SoftPLC

P0230

REM Command Selection

0 = I,O Keys

1

cfg

21

57

1 = DIx

2 = Serial/USB

3 = Anybus-CC

4 = SoftPLC

P0231

AI1 Signal Function

0 = Not Used

0

cfg

23

58

P0232

AI1 Gain

0.000 to 9.999

1.000

23

58

P0233

AI1 Signal Type

0 = 0 to 10V/20mA

0

cfg

23

59

1 = 4 to 20 mA

2 = 10V/20mA to 0

3 = 20 to 4 mA

P0234

AI1 Offset

-100.00 to 100.00 %

0.00 %

23

58

P0235

AI1 Filter

0.00 to 16.00 s

0.00 s

23

59

P0236

AI2 Signal Function

0 = Not Used

0

cfg

23

58

P0237

AI2 Gain

0.000 to 9.999

1.000

23

58

P0238

AI2 Signal Type

0 = 0 to 10V/20mA

0

cfg

23

59

1 = 4 to 20 mA

2 = 10V/20mA to 0

3 = 20 to 4 mA

4 = -10 to +10V

Quick Parameter Reference .

SSW7000 | 15

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0239

AI2 Offset

-100.00 to 100.00 %

0.00 %

23

58

P0240

AI2 Filter

0.00 to 16.00 s

0.00 s

23

59

P0251

AO1 Function

0 = Not Used

0

24

60

1 = SSW Current %

2 = Line Voltage

3 = Output Voltage

4 = Power Factor

5 = Ther.Clas.Pro.

6 = Output Power W

7 = Output Power VA

8 = Motor Torque %

9 = P0696 Value

10 = P0697 Value

11 = R-U SCRs Temp.

12 = S-V SCRs Temp.

13 = T-W SCRs Temp.

14 = SoftPLC

P0252

AO1 Gain

0.000 to 9.999

1.000

24

61

P0253

AO1 Signal Type

0 = 0 to 10V/20mA

0

cfg

24

62

1 = 4 to 20 mA

2 = 10V/20mA to 0

3 = 20 to 4 mA

P0254

AO2 Function

See options in P0251

0

24

60

P0255

AO2 Gain

0.000 to 9.999

1.000

24

61

P0256

AO2 Signal Type

0 = 0 to 10V/20mA

0

cfg

24

62

1 = 4 to 20 mA

2 = 10V/20mA to 0

3 = 20 to 4 mA

P0263

DI1 Function

0 = Not Used

2

cfg

25

63

1 = Start/Stop

2 = Start(3 Wires)

3 = Stop (3 Wires)

4 = General Enable

5 = FWD/REV

6 = LOC/REM

7 = No Ext. Fault

8 = JOG

9 = Brake Off

10 = Reset

11 = No Ext. Alarm

12 = Load User 1/2

13 = Load User 3

14 = Trace Function

15 = Fuse Ok

16 = Blocking PFC

P0264 DI2 Function See options in P0263 3 cfg 25 63

P0265

DI3 Function

See options in P0263

0

cfg

25

63

P0266

DI4 Function

See options in P0263

0

cfg

25

63

P0267

DI5 Function

See options in P0263

0

cfg

25

63

P0268

DI6 Function

See options in P0263

0

cfg

25

63

P0275

DO1 Function

0 = Not Used

1

cfg

26

65

1 = Running

2 = Full Voltage

3 = Bypass

Quick Parameter Reference .

16 | SSW7000

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

4 = Foward

5 = DC Braking

6 = Without Fault

7 = With Fault

8 = Without Alarm

9 = With Alarm

10 = No Fault/Alarm

11 = SoftPLC

12 = P0695 Content

13 = Not Used

14 = Control PFC

15 = Blocking PFC

P0276

DO2 Function

0 = Not Used

3

cfg

26

66

1 = Running

2 = Full Voltage

3 = Bypass

4 = Reverse

5 = DC Braking

6 = Without Fault

7 = With Fault

8 = Without Alarm

9 = With Alarm

10 = No Fault/Alarm

11 = SoftPLC

12 = P0695 Content

13 = Not Used

14 = Control PFC

15 = Blocking PFC

P0277

DO3 Function

0 = Not Used

7

cfg

26

66

1 = Running

2 = Full Voltage

3 = Bypass

4 = Not Used

5 = DC Braking

6 = Without Fault

7 = With Fault

8 = Without Alarm

9 = With Alarm

10 = No Fault/Alarm

11 = SoftPLC

12 = P0695 Content

13 = Arc Detection

14 = Control PFC

15 = Blocking PFC

P0280

PFC Discharge Time

60 to 600 s

300 s

cfg

67

P0295

Nominal SSW Current

0 = 10 A

1

cfg

27

83

1 = 70 A SSW7000C

2 = 70 A SSW7000

3 = 125 A SSW7000C

4 = 180 A SSW7000

5 = 250 A SSW7000C

6 = 300 A SSW7000

7 = 359 A SSW7000C

Quick Parameter Reference .

SSW7000 | 17

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

8 = 360 A SSW7000

9 = Reserved

10 = 400 A SSW7000

11 = Reserved

12 = 500 A SSW7000

13 = Reserved

14 = 600 A SSW7000

P0296

Nominal SSW Voltage

0 = 220/500 V

0

cfg

27

83

1 = 2300 V

2 = 4160 V

3 = 6900 V

4 = 13800 V

P0308

SSW Serial Address

1 to 247

1

cfg

139

P0310

Serial Baud Rate

0 = 9600 bits/s

0

cfg

139

1 = 19200 bits/s

2 = 38400 bits/s

3 = 57600 bits/s

P0311

Serial Bytes Config.

0 = 8 bits, no, 1

3

cfg

139

1 = 8 bits, even,1

2 = 8 bits, odd, 1

3 = 8 bits, no, 2

4 = 8 bits, even,2

5 = 8 bits, odd, 2

P0313

Comm. Error Action

0 = Off

0

140

1 = Ramp Stop

2 = General Disab.

3 = Goes to LOC

4 = Off

5 = Causes Fault

P0314

Serial Com. Watchdog

0.0 to 999.0 s

0.0 s

cfg

139

P0316

Serial Interf. Status

0 = Off

ro

08

139

1 = On

2 = Watchdog Error

P0317

Oriented Start-up

0 = No

0

cfg

02

86

1 = Yes

P0318

Copy Function MemCard

0 = Off

0

cfg

04

53

1 = SSW -> MemCard

2 = MemCard -> SSW

P0319

Copy Function HMI

0 = Off

0

cfg

04, 20

54

1 = SSW -> HMI

2 = HMI -> SSW

P0320

Test Mode

0 = No

0

cfg

09

87

1 = Yes

P0321

Test Mode Sequence

0 = Not Used

0

cfg

87

1 = R_U SCR On

2 = S_V SCR On

3 = T_W SCR On

4 = Fan On

5 = Bypass C. On

6 = Main C. On

7 = R_U CT Test

8 = S_V CT Test

9 = T_W CT Test

P0330

Safe Sectioning

0 = No

0

cfg

10

88

Quick Parameter Reference .

18 | SSW7000

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

1 = Yes

P0331

Safe Sectioning Sequence

0 = Power Off?

0

ro

10

88

1 = Main Contactor On

2 = Bypass Contactor On

3 = Bypass Contactor Off

4 = Main Contactor Off

5 = End

P0400

Nominal Motor Voltage

0 to 13800 V

3300 V

cfg

22, 28

84

P0401

Nominal Motor Current

0.0 to 1200.0 A

100.0 A

cfg

22, 28

84

P0402

Nominal Motor Speed

0 to 3600 rpm

1780 rpm

cfg

22, 28

84

P0404

Nominal Motor Power

1 to 9999 kW

570 kW

cfg

22, 28

85

P0405

Nomi. Mot. Power Fac.

0.00 to 1.00

0.89

cfg

22, 28

85

P0500

Braking Methods

0 = Inactive

0

cfg

29

89

1 = Reverse Braki.

2 = Optimal Braki.

3 = DC Braking

P0501

Braking Time

1 to 299 s

10 s

cfg

29

91

P0502

Braking Voltage Level

30 to 70 %

30 %

29

92

P0503

Braking End Detection

0 = Inactive

0

cfg

29

92

1 = Automatic

P0510

JOG

0 = Inactive

0

cfg

30

93

1 = Active

P0511

Jog Level

10 to 100 %

30 %

30

93

P0520

Kick Start

0 = Inactive

0

cfg

31

94

1 = Active

P0521

Kick Start Time

0.1 to 2.0 s

0.1 s

31

94

P0522

Kick Start Voltage

70 to 90 %

70 %

31

94

P0523

Kick Start Current

300 to 700 %

500 %

31

94

P0550

Trace Trigger Signal

0 = Inactive

0

35

142

1 = SSW Current %

2 = Line Voltage

3 = Output Voltage

4 = Power Factor

5 = Ther.Clas.Pro.

6 = Output Power W

7 = React.Power VA

8 = Motor Torque %

P0551

Trigger Level

0.0 to 600.0 %

0.0 %

35

142

P0552

Trigger Condition

0 = P0550* = P0551

5

35

143

1 = P0550* <>P0551

2 = P0550* > P0551

3 = P0550* < P0551

4 = Alarm

5 = Fault

6 = DIx

P0553

Trace Sampling Period

1 to 1300

1

35

143

P0554

Trace Pre-Trigger

0 to 100 %

0 %

35

143

P0559

Trace Max. Memory

0 to 100 %

0 %

35

144

P0560

Trace Avail. Memory

0 to 100 %

ro

08, 35

144

P0561

Trace Channel 1 (CH1)

See options in P0550

1

35

145

P0562

Trace Channel 2 (CH2)

See options in P0550

2

35

145

P0563

Trace Channel 3 (CH3)

See options in P0550

3

35

145

P0564

Trace Channel 4 (CH4)

See options in P0550

0

35

145

Quick Parameter Reference .

SSW7000 | 19

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0571

Start Trace Function

0 = Inactive

0

35

145

1 = Active

P0572

Trace Trig. Day/Month

00/00 to 31/12

ro

08, 35

145

P0573

Trace Trigger Year

00 to 99

ro

08, 35

145

P0574

Trace Trigger Time

00:00 to 23:59

ro

08, 35

146

P0575 Trace Trigger Seconds 00 to 59 ro 08, 35 146

P0576

Trace Function Status

0 = Inactive

ro

08, 35

146

1 = Waiting

2 = Triggered

3 = Concluded

P0680

SSW Status Word

Bit 0 = Running

ro

08

140

Bit 1 = Gener. Enabled

Bit 2 = JOG

Bit 3 = Ramp Up

Bit 4 = Delay P831

Bit 5 = Full Voltage

Bit 6 = Alarm

Bit 7 = Ramp Down

Bit 8 = Remote

Bit 9 = Braking

Bit 10 = FWD/REV

Bit 11 = Reverse

Bit 12 = Bypass

Bit 13 = Config. Mode

Bit 14 = Power Supply

Bit 15 = Fault

P0682

Serial/USB Control

Bit 0 = Run/Stop

ro

08

139

Bit 1 = Gener. Enabled

Bit 2 = JOG

Bit 3 = FWD/REV

Bit 4 = LOC/REM

Bit 5...6 = Reserved

Bit 7 = Reset

Bit 8....15 = Reserved

P0686

Anybus-CC Control

See options in P0682

ro

08

139

P0692

Config. Mode Status

Bit 0 = Orie. Start-Up

ro

08

140

Bit 1 = C1-C2 WaitCom.

Bit 2 = Test Mode

Bit 3 = Copy Mem.Card

Bit 4 = Copy HMI

Bit 5 = Copy Firmware

Bit 6 = Reset Needs

Bit 7 = Types Control

Bit 8 = Incompatible

Bit 9 = Safe Sectioning

Bit 10 ....15 = Reserved

P0693

Config. Mode Control

Bit 0 = Abort Startup

ro

08

140

Bit 1 = Reserved

Bit 2 = Abort T. Mode

Bit 3 = Abort Safe Sectioning

Bit 4 ....6 = Reserved

Bit 7 = Abort Control

Bit 8....15 = Reserved

P0695

DOx Value

0000h to FFFFh

ro

08

140

Quick Parameter Reference .

20 | SSW7000

Param. Function Adjustable Range

Factory

Setting

User

Setting

Propr. Groups Page

P0696

AOx Value 1

-32768 to 32767

ro

08

140

P0697

AOx Value 2

-32768 to 32767

ro

08

140

P0723

Anybus Identification

0 = Disabled

ro

08

139

1 = RS232

2 = RS422

3 = USB

4 = Serial Server

5 = Bluetooth

6 = Zigbee

7 = Reserved

8 = Reserved

9 = Reserved

10 = RS485

11 = Reserved

12 = Reserved

13 = Reserved

14 = Reserved

15 = Reserved

16 = Profibus DP

17 = DeviceNet

18 = CANopen

19 = EtherNet/IP

20 = CC-Link

21 = Modbus-TCP

22 = Modbus-RTU

23 = Profinet IO

24 = Reserved

25 = Reserved

P0724

Anybus Comm. Status

0 = Disabled

ro

08

139

1 = Not Supported

2 = Access Error

3 = Offline

4 = Online

P0725

Anybus Address

0 to 255

0

cfg

139

P0726

Anybus Baud Rate

0 to 3

0

cfg

139

P0728

Anybus Read Word #2

0 to 1059

0

cfg

139

P0729

Anybus Read Word #3

0 to 1059

0

cfg

139

P0730

Anybus Read Word #4

0 to 1059

0

cfg

139

P0731

Anybus Read Word #5

0 to 1059

0

cfg

139

P0732

Anybus Read Word #6

0 to 1059

0

cfg

139

P0733

Anybus Read Word #7

0 to 1059

0

cfg

139

P0734

Anybus Read Word #8

0 to 1059

0

cfg

139

P0735

Anybus Read Word #9

0 to 1059

0

cfg

139

P0736

Anybus Read Word #10

0 to 1059

0

cfg

139

P0737

Anybus Read Word #11

0 to 1059

0

cfg

139

P0738

Anybus Read Word #12

0 to 1059

0

cfg

139

P0739

Anybus Read Word #13

0 to 1059

0

cfg

139

P0740

Anybus Read Word #14

0 to 1059

0

cfg

139

P0741

Anybus Read Word #15

0 to 1059

0

cfg

139

P0742

Anybus Read Word #16

0 to 1059

0

cfg

139

P0743

Anybus Read Word #17

0 to 1059

0

cfg

139

P0744

Anybus Read Word #18

0 to 1059

0

cfg

139

P0745

Anybus Read Word #19

0 to 1059

0

cfg

139

Page is loading ...

WEG SSW7000 Programming Manual

WEG SSW7000 Programming Manual

Related papers

Other documents