Tyan B5121G14S2 User manual

1

http://www.TYAN.com

Transport GS14 / / / B5121G14S2

Revision 1.02

manual may be reproduced or translated without prior written consent from TYAN

Computer Corp.

All registered and unregistered trademarks and company names contained in this

manual are property of their respective owners including, but not limited to the

following:

TYAN and Transport GS14 (B5121G14S2) are trademarks of TYAN Computer

Corporation.

Intel and combinations thereof are trademarks of Intel Corporation.

Phoenix BIOS is a trademark of Phoenix Technology.

Microsoft and Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

ATI, ATI RAGE is a trademark of ATI Technologies Incorporated.

Winbond is a trademark of Winbond Electronics Corporation.

Information contained in this document is furnished by TYAN Computer Corporation

and has been reviewed for accuracy and reliability prior to printing. TYAN assumes no

liability whatsoever, and disclaims any express or implied warranty, relating to sale

and/or use of TYAN products including liability or warranties relating to fitness for a

particular purpose or merchantability. TYAN retains the right to make changes to

product descriptions and/or specifications at any time, without notice. In no event will

TYAN be held liable for any direct or indirect, incidental or consequential damage, loss

of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

WARNING: This product should be serviced only by qualified service engineers. Do not

remove the chassis cover or attempt to service this product unless you are qualified to do

so. Once the chassis cover is removed there is a risk of electric shock which could lead

to serious injury or death.

2

http://www.TYAN.com

1 Table of Contents

Before You Begin............................................................................ 4

Safety Precautions ........................................................................... 4

Chapter 1 Introduction............................................................................................ 5

1.1 Unpacking........................................................................................ 5

1.2 Specifications .................................................................................. 8

1.3 System View.................................................................................... 9

Front View....................................................................................... 9

Rear View...................................................................................... 10

System Assembly Flowchart......................................................... 12

Chapter 2 Hardware Installation.......................................................................... 15

2.1 System Assembly .......................................................................... 13

Safety Considerations.................................................................... 13

Opening the Cover......................................................................... 13

Installing the CPU ......................................................................... 13

Installing System Memory............................................................. 17

Installing a Hard Disk Drive.......................................................... 19

2.2 Adding a CD Drive........................................................................ 22

With a Ultra ATA/100 Hard Disk Drive Installed......................... 22

Without a Ultra ATA/100 Hard Disk Drive Installed.................... 24

2.3 Rack Mounting (Option)................................................................ 24

Cabinet Slides and Ears................................................................. 25

Cabinet into the Rack .................................................................... 27

Locking Tab................................................................................... 27

2.4 Setting Up the System ................................................................... 28

Placing the System......................................................................... 28

Making the Connection ................................................................. 28

For 32-bit OS................................................................................. 31

For 64-bit OS................................................................................. 32

Chapter 3 Software Installation............................................................................ 33

3.1 Installation Instructions for Windows............................................ 33

Windows Installation Notes........................................................... 33

Chipset Driver ............................................................................... 33

VGA Driver................................................................................... 34

Intel Matrix Storage Manager........................................................ 34

3

http://www.TYAN.com

Intel 82562GT NIC (Network Interface Card) Driver................... 34

Broadcom 5721 LAN Driver......................................................... 35

LCD Driver................................................................................................35

3.2 Installation Instructions for Linux (RedHat/Fedora/SuSE)............ 36

Linux Installation Notes................................................................. 36

VGA Driver................................................................................... 36

Intel 82562GT NIC (Network Interface Card) Driver

Broadcom 5721 Driver.................................................................. 37

LCD Driver.................................................................................... 37

3.3 Installation Instructions for FreeBSD 5.4...................................... 37

Intel 82562GT NIC (Network Interface Card) Driver................... 37

Broadcom 5721 Driver.................................................................. 37

Chapter 4 BIOS Setup............................................................................................ 39

4.1 BIOS Setup Program ..................................................................... 39

Starting BIOS Setup ......................................................................39

Main Menu ....................................................................................40

Advanced Menu............................................................................. 41

Security Menu................................................................................ 42

Power Menu................................................................................... 43

Monitor Menu................................................................................ 43

Boot Menu..................................................................................... 44

Exit Menu...................................................................................... 44

4.2 Resetting BIOS Setup.................................................................... 45

Chapter 5 Expanding the System..........................................................................47

5.1 Opening the Cover......................................................................... 47

5.2 Installing an Expansion Card......................................................... 48

5.3 Adding a Secondary Hard Disk Drive........................................... 49

Chapter 6 System Parts Replacement................................................................... 53

6.1 Opening the Cover......................................................................... 53

6.2 Removing the Front Bezel............................................................. 54

6.3 Replacing the Button Board........................................................... 55

6.4 Replacing the Fan.......................................................................... 56

6.5 Replacing the USB Board.............................................................. 57

6.6 Replacing the LCD Module........................................................... 58

6.7 Replacing the Power Supply.......................................................... 59

6.8 Replacing the Motherboard ........................................................... 60

Chapter 7 Appendix................................................................................................ 61

Caution Texts Concerning Lithium Batteries......................................... 61

Technical Support................................................................................... 62

4

http://www.TYAN.com

Before You Begin

This manual provides hardware-related information of the system for administrators

who use it to develop and host web sites. The administrators should be familiar with

operating systems and web browsers.

Depending on the model purchased, your system may come with pre-installed software.

For software information, refer to the documentation accompanying the software.

Safety Precautions

z Use the type of power indicated on the marking label.

z Ensure that electrical circuits are not overloaded; consider the nameplate ratings of

all the connected equipment and ensure that you have over current protection.

z Do not disable the power cord ground feature. This equipment was designed to

connect to a grounded (earthed) power outlet. The grounding plug is an important

safety feature.

z Ensure that the power outlet is located or installed near the equipment and is easily

accessible.

z Do not allow anything to rest on the power cord. Do not locate this product where

persons will walk on the cord.

z Ensure the ambient temperature around the equipment (which may be higher than

the room temperature) is within the limits specified in section 1.2.

z Slots and openings in the cabinet are provided for ventilation. Do not block or

cover these openings. Do not push objects of any kind into cabinet slots or

openings.

5

http://www.TYAN.com

1 Introduction

Congratulations on purchasing the system. This chapter introduces the features and

functions of the product.

1.1 Unpacking

After unpacking the shipping carton, you should find these standard items:

1× B5121G14S2 case kit

1× motherboard (pre-installed)

1× LCD module (pre-installed)

1× button board (pre-installed)

1× USB board (pre-installed)

1× fan assembly 40*28 mm (pre-installed)

2× fan assembly 40*56 mm (pre-installed)

1× power supply 1U ATX 300 W (pre-installed)

1× riser board 32-bit / 33 MHz (pre-installed)

1× fan holder (pre-installed)

6

http://www.TYAN.com

And the following accessories:

1× pair of ear bracket

1× heatsink

1× primary serial ATA cable

1× secondary serial ATA cable

1× HDD power to pin-header cable

1× primary serial ATA power cable

1× secondary serial ATA power cable

1× IDE cable

1× power Y-cable

2× power cord (USA and Germany)

4× rubber feet

1× TYAN driver CD

1× B5121 User’s Manual

1× Rail Kit

Inspect all the items. If any item is damaged or missing, notify your dealer immediately.

Keep the shipping carton and packing materials in case you need to ship or store the

computer in the future.

Note: The following items are included in the Rail Kit:

1) 1× Slide

2) 4 x Bracket Rail Kit

7

http://www.TYAN.com

3) 4 x Screw Kit

4) 1 x pair of Ear bracket (Please refer to the above picture for them)

5) 1 x pair of Handle Kit

6) 1 x Packing Kit (Including 1 x Box, 2 x Sponge, 1 x End cap )

7) 1 x Instruction Sheet

8

http://www.TYAN.com

1.2 Specifications

NOTE: Specifications are subject to change without notice.

Processor

• Single socket-T LGA775

• Intel

®

Pentium 4 Prescott 5xx/6xx or

Celeron D 3xx processor

• Supports 533/800 MHz FSB

Chipset

• Intel 915GV (NorthBridge)

• ICH6R (SouthBridge)

• SMC LPC47M172 Super I/O chip

• Winbond 83792 hardware monitor

Memory

• Four 240-pin DDR2 DIMM slots

• Single/dual-channel mode support

• Up to 4 GB of non-ECC DDR2

Expansion Slot

• One 32-bit / 33 MHz PCI v2.3 slot on riser

card

Integrated PCI Graphics

• 915GV embedded graphic controller

• Shared system memory 1 MB

(4/8/16/32/64/128 MB)

External I/O Ports (Rear)

• One 9-pin UART serial port

• One VGA port

• Two RJ-45 LAN connectors

• Two USB 2.0 ports

• One PS/2 keyboard/mouse connector

Front Panel Features

• LED Indicators

– Power

– Two LAN (Giga, 10/100M)

– HDD

• LCD interface

– 2 x 16 digits

– Connected via COM2

– Four direction buttons plus one “Select”

and one “Cancel” button

• Two USB 2.0 ports

NOS (Network O/S) Support

• Windows 2003 Server 64-bit and 32-bit

• Windows XP

• Linux RHEL ES 3.0

• Linux RHEL 4.0

• Fedora Core 3 / Core 4

Networking

• One 10/100 Ethernet LAN port from

ICH6R with Intel® 82562GT PHY

• One gigabit Ethernet LAN port (Broadcom

BCM5721)

• Supports PXE and WOL

Storage Capacity

• One IDE (Ultra ATA/100) HDD or two

SATA HDDs

• SATA HDDs support RAID0, RAID1

Integrated Hardware Monitoring

• CPU temperature and voltage monitoring

• Automatic fan speed control mode

• CPU and system fan speed monitoring

and control

• 5 x 3-pin header for system fans

• Monitor up to 6 processor VID bits

BIOS

• Phoenix BIOS on 8 MB Flash ROM

• ACPI 2.0 / APM 1.2

• SM BIOS 2.3.3 (backward-compatible with

DMI 2.0)

• UCR and LAN remote boot (PXE) support

• Power Management: S1 and S5-type

Environment

• Operating temperature:

5

0

C (41

0

F) to 35

0

C (95

0

F)

• Operating relative humidity:

0 % to 80 % non-condensing

• Operating altitude:

–50 ft to 10,000 ft

Cabinet Form Factor

• Sub-1U rack-mountable chassis

• Dimension:

W16.7 x D15.3 x H1.7 inch

W424 x D387.7 x H43.5 mm

Power Supply

• ATX 12 V 1U 300 W with PSU

Regulatory

• FCC Class A

• CE (Declaration of Conformity)

• UL/cUL

• TUV

9

http://www.TYAN.com

1.3 System View

Front View

Ref Component Description

n

Power Button

Turns the power on and off (soft-off).

o

Power Indicator

Glows green when the power is on.

p

LAN1 Indicator

Indicates a network connection on LAN1 (internal connection).

q

LAN2 Indicator

Indicates a network connection on LAN2 (external connection).

r

Hard Disk Drive

Indicator

Indicates activity on the hard disk drive.

s

USB Ports

Each of the two ports connects a USB device.

t

LCD Screen

Displays messages and values entered.

u

Control Buttons

Allow you to enter network configuration information, reboot the system,

and power down the system.

10

http://www.TYAN.com

Rear View

Ref Component Description

n

Ventilation Openings

Maintain proper operating temperature. Do not cover or block the

openings.

o

Power Connector

Connects the power cord.

p

Power Switch

Turns the main power of the system on and off.

q

PS/2 Keyboard/

Mouse Connector

Connects a PS/2 keyboard/mouse.

r

LAN2 Connector

Connects the LAN cable for external network connection.

s

LAN1 Connector

Connects the LAN cable for internal network connection.

t

Serial Port

Connects a serial device.

u

VGA Port

Connects an external CRT monitor.

v

USB Ports

Each of the two ports connects a USB device.

w

Expansion Slot

Allow you to install a PCI card.

11

http://www.TYAN.com

2 Hardware Installation

This chapter, which is divided into two sections, provides instructions on the hardware

installation of the system. System Assembly section illustrates how to assemble each

component of the system. Rack Mounting section describes the procedures for

mounting the system into the rack. You can use the system assembly flowchart and the

chart next to determine the proper sequence for removing or installing components to

the server.

System Assembly

Rack Mounting

Cabinet Cover

CPU and Heatsink

Hard Disk Drive

Cabinet

Rails and Ears

Cabinet into the Rack

Locking Tab

DIMM

Start

12

http://www.TYAN.com

System Assembly Flowchart

The following flowchart shows the basic procedures of system assembly:

FINISH

START

INSTALL

SYSTEM MEMORY

REMOVE CABINET COVER

INSTALL

CPU AND HEATSINK

INSTALL

HARD DISK DRIVE

CO

NNE

C

T H

A

RD DI

S

K

DRIVE CABLE

AND POWER CORD

CHECK IF ALL PARTS

A

RE PROPERLY CONNECTED

REPLACE

CABINET COVER

13

http://www.TYAN.com

2.1 System Assembly

When installing a device, be sure to read the instructions accompanying the device

together with the relevant section in this chapter.

Safety Considerations

z Static electricity can destroy electronic devices. Whenever you handle an option

outside of its protective packaging, first discharge any static electricity from your

body by touching a protective grounding device or unpainted metal on the rear

panel of the system before unplugging the power cord.

z Before you install any option, turn all power switches off. Unplug all power cords

from the system and all peripherals. Leaving the power on can cause serious

damage to your system.

z If the system is mounted on an equipment rack, remove the system from the rack

and take it to a service area. Do not attempt to disassemble the system while it is

still in the equipment rack.

Opening the Cover

1. Remove two screws from the back of the system. Pull the cover backward to detach

it.

2. To replace the cover, slide the cover forward and replace the two screws.

Installing the CPU

Your system supports socket-T LGA775 Intel Pentium 4 processor.

1. Remove the cabinet cover (see previous section).

14

http://www.TYAN.com

2. Find the socket-T on the motherboard.

3. Remove the black plastic protective cover on top of the socket-T (keep this for

future use in case you will need it).

15

http://www.TYAN.com

4. Lift the load lever up to the vertical position, then open the load plate.

5. Align the CPU so its Pin 1 corner (beveled corner) is at the Pin 1 corner of the

socket-T. Then insert the CPU's pins into the corresponding holes in the socket.

CAUTION: The CPU fits only in one correct orientation. Improper insertion of the CPU into

the socket may bend the pins on the socket-T and cause damage to the motherboard.

6. Apply some thermal grease on top of the CPU to aid in heat dissipation.

16

http://www.TYAN.com

7. Close the load plate, then carefully press the load lever downward to latch unto the

hook to secure it.

8. Place the heatsink assembly on top of the CPU and align the four points of the

heatsink socket. Secure with four screws following a diagonal sequence.

CAUTION: The heatsink must be installed, otherwise the CPU and/or motherboard will

overheat and be damaged.

9. Replace the cabinet cover.

17

http://www.TYAN.com

Installing System Memory

Your system has four 240-pin non-ECC DDR2 DIMM (Double Data Rate 2 Dual

In-line Memory Module) sockets to support a maximum of 4 GB.

Dual Channel Mode, instead of the default Single Channel Mode, can be enabled to

allow you to maximize the DIMMs performance. The installed DIMMs must meet the

following conditions:

z Matched DIMM configuration

(channel A comprises DIMM1 and DIMM2 while channel B comprises DIMM3 and

DIMM4) :

– same density and DRAM technology in each channel

(e.g., 128 MB, 256 MB, 512 MB, 1 GB, etc.)

– same DRAM bus width (e.g., ×8 or ×16) in each channel

– both DIMM should be either single-sided or double-sided

NOTE:

z The following conditions do not need to be met: same timing specifications and same

DDR2 speed.

z Memory interface speed will be set to the slowest speed of DIMM populated.

z Always install DIMMs with the same CAS latency. For optimum compatibility, it is

recommended that you obtain memory modules from the same vendor.

z DIMM installed into any one slot will function in Single Channel Mode.

z When the total DIMMs installed is over 4GB, only 4 GB may be available for system

use due to chipset limitation.

z Installing DIMMs other than the recommended configurations may cause memory

sizing error or system boot failure. Use any of the recommended configurations in the

next table.

Slots

Mode

DIMM1 DIMM2 DIMM3 DIMM4

Populated

Single Channel

Populated

Populated Populated

Dual Channel

Populated Populated Populated Populated

Follow this procedure to install a DIMM:

1. Open the cabinet cover (see previous section).

18

http://www.TYAN.com

2. Locate the DIMM sockets.

3. To install the DIMM, make sure the retaining clips are in the unlocked position,

then align the DIMM’s notched end with the socket’s corresponding end and firmly

insert the DIMM into the socket. Finally push the retaining clips inwards to lock the

DIMM in place.

NOTE: The DIMM modules will fit in only one orientation. Do not touch the memory

module’s connectors. Handle only by the edges.

WARNING: DIMM modules become extremely hot during operation.

4. Replace the cabinet cover.

19

http://www.TYAN.com

Installing a Hard Disk Drive

NOTE: Make sure that the jumper setting of the hard disk drive is set to “Master.” (See the

hard disk drive’s documentation for information.)

WARNING: Please attach the hard bracket to the chassis to prevent enlarging the screw

holes even if you will not use hard disk drive

It is advised that you select a hard disk drive that meets the following specifications. A

hard disk drive that does not meet these specifications can cause reliability problems in

your system.

z Peak current draw: must not exceed 1.8 amperes maximum (at 5 volts) and 0.7

amperes maximum (at 12 volts)

z Rotational speed: 5400/7200 rpm

z Interface: Serial ATA

z Operating temperature: must be able to operate in environments up to 55 °C

z Operating humidity: 10 % to 90 % (non-condensing)

z IDE and SATA hard disk drives cannot be used in combination for RAID function

1. Remove the cabinet cover (see previous section).

20

http://www.TYAN.com

2. Locate the bracket for the primary hard disk drive, next to the power supply.

Remove the screw and slide the bracket off the metal tabs to detach it.

3. Secure the hard disk drive to the bracket with four bottom screws.

4. Fit the bracket with the hard disk drive back into place and secure with one screw.

5. Connect one end of the included Serial ATA data cable to the primary Serial ATA

connector (n) , connect the other end to the rear of hard disk drive 2 (o) (see

chapter 5 for adding a second hard disk drive), and insert the data cable into the wire

clip (p) . Connect the single end of the included power Y-cable to the power

Page is loading ...

Tyan B5121G14S2 User manual

This manual is also suitable for

Tyan B5121G14S2 User manual

Related papers

Other documents