2. Boost Auto Parts
  3. 2014-2019 GM All Lights Mod (6 High Mod)

Boost Auto Parts 2014-2019 GM All Lights Mod (6 High Mod) Installation guide

  • Hello! I have reviewed the installation instructions for the Boost Auto Parts All Lights Mod designed for 2014-2019 GM trucks and SUVs. This document details how to install the mod that allows your fog lights to stay on when your high beams are activated. The installation uses T-taps and takes about 5 minutes. I'm ready to assist you with any specific questions you have about the installation process or the product itself.
  • What does the All Lights Mod do?
    How long does the installation take?
    What tools are required for installation?
    Which vehicles are compatible with this mod?
1
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2014-2019 GM All Lights Mod Installation
All Lights Mod For
2014-2019 GM Trucks & SUV’s
2014-2019 GM All Lights Mod Installation
2
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
INTRODUCTION
This document will be covering the installation of our 2007-2021 GM All Lights Mod, on 2014-
2019 GM trucks. Once installed, the factory fog lights will turn on and stay on once the high
beams are activated. This installation requires no additional tools and will take only 5 minutes to
complete.
This procedure is for 2014 1500 GM trucks, 2015-2018 1500/2500/3500 GM Trucks, and 2019
2500/3500 Trucks. For exact fitment reference the product page.
Boost Auto Parts offers a variety of parts and accessories for your GM Trucks. To purchase
additional parts and accessories Click Here.
Overview: Pg. 3
Locating & Removing BCM Connector: Pg. 4
Installing T-taps: Pg. 5
Installing Module: Pg. 6
TABLE OF CONTENTS
3
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2014-2019 GM All Lights Mod Installation
For 2014-2019 GM Trucks
Difculty: Easy
Tools Needed: None
Parts Needed: 2007-2021 GM All Lights
Mod
Video Tutorial: Fog Lights on with
High Beams (All Lights Mod) 2014-2019
Silverado Sierra Tahoe Yukon Suburban
How to Install GM All Lights Mod For 2014-2019 GM
Trucks & SUVs
Your vehicle must REMAIN OFF while any BCM
connectors are removed.
Caution:
!
2014-2019 GM All Lights Mod Installation
4
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
Step 1:
Remove the driver side kick panel to expose the
wiring just behind the OBDII connector. Next,
locate the BCM, which is found under driver side
of the dash to the upper left hand side. Remove
the brown BCM connector by pushing the tab
inwards and pulling down.
Step 2:
Identify the wires in each pin location on the
brown connector. Pin 10, shown here in red, is
located 3 rows up and 3 columns from the left.
Pin 18, shown here in green, is located 2 rows
up and 3 columns over from the right. Wire
color may vary between vehicles, therefore, pin
locations should be your primary reference.
Disclaimer:
Incorrect pin locations will result
in unexpected events such as
activating the horn. Relocate the
correct pin slots and move the T-taps to their
proper wires. T-taps can be reused if taken off
in one piece.
5
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2014-2019 GM All Lights Mod Installation
Step 3:
Utilizing the T-taps provided, attach one to
the corresponding wire found in slot 10. Make
sure to completely close the T-taps for proper
connection.
If your unfamiliar with T-taps, Click Here for
additional information.
Step 4
Utilizing the T-taps provided, attach one to
the corresponding wire found in slot 18. For
additional leverage, pliers can be used to close
T-taps.
If your unfamiliar with T-taps, Click Here for
additional information.
2014-2019 GM All Lights Mod Installation
6
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
Step 5:
Once both T-taps are installed, find the blue
marked end on the module. The marked end
needs to be plugged into the wire tapped to pin
10.
Proceed to bend the flexible module to
connect the other T-tap. If your unfamiliar with
quick disconnects, Click Here for additional
instructions.
Step 6:
Lastly, reinstall the BCM connector. A click
sound will be heard confirming the connector
has been fully seated.
Disclaimer:
Make sure that the BLUEBLUE marked
side connects to the wire tapped
into pin 10.
7
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2014-2019 GM All Lights Mod Installation
If you experience any difficulties or
complications during your install, feel free to
reach out to our Technical Support Team.
Support@boostautoparts.com
765-831-2830
Your GM All Lights Mod Install is Complete!
/