2. Boost Auto Parts
  3. All Lights Mod
All Lights Mod

Boost Auto Parts All Lights Mod User manual

  • Hello! I've reviewed the user manual for the Boost Auto Parts All Lights Mod for 2015+ Colorado and Canyon trucks. This modification enables your fog lights to remain on when high beams are activated. The manual details a simple installation process using T-taps and a module. I'm ready to answer your questions about the installation and the functionality of this mod.
  • What vehicles are compatible with this mod?
    How long does the installation take?
    What tools are needed for installation?
1
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2015+ Colorado & Canyon All Lights Mod Installation
All Lights Mod
For 2015+ Colorado & Canyon
2015+ Colorado & Canyon All Lights Mod Installation
2
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
INTRODUCTION
This document will be covering the installation of our 2007-2021 GM All Lights Mod on 2015 and
newer Chevy Colorado and GMC Canyon trucks. Once installed, the factory fog lights will turn on
and stay on when the high beams are activated. This installation requires no additional tools and
will take only 5 minutes to complete.
This procedure is for 2015+ GM Colorado and Canyon trucks. For exact fitment reference the
product page.
Boost Auto Parts offers a variety of other items and accessories for your GM Trucks. To purchase
additional parts and accessories Click Here.
Overview: Pg. 3
Removing BCM Connector: Pg. 4
Installing T-taps: Pg. 5
Installing Module: Pg. 6
TABLE OF CONTENTS
Overview: Pg. 3
Locating & Removing BCM Connector: Pg. 4
Installing T-taps: Pg. 5
Installing Module: Pg. 6
3
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2015+ Colorado & Canyon All Lights Mod Installation
For 2015+ Colorados and Canyons
Difculty: Easy
Tools Needed: None
Parts Needed: 2007-2021 GM All Lights
Mod
Video Tutorial: Fog Lights on With
High Beams (All Lights Mod) 2015-2021
Colorado and Canyon
How to Install GM All Lights Mod for 2015 and Newer
Colorado & Canyon Trucks
Your vehicle must REMAIN OFF while any BCM
connectors are removed.
Caution:
!
2015+ Colorado & Canyon All Lights Mod Installation
4
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
Step 2:
Identify the wires in each pin location on the
brown connector. Pin 13, shown here in red,
is located in the third row up and the second
column from the right.
Pin 18, shown here in green, is in the second
row up and the third column over from the
right. Wire color may vary between vehicles,
therefore, pin location should be your primary
reference.
Step 1A:
First, locate the BCM under the drivers side dash.
Here we show the driver side kick panel removed
to give you an idea of the location but removing
this is not necessary.
Step 1B:
Once you locate the BCM, you will need to
unlatch and remove the brown connector. The
wires needed for this install will be found in this
brown BCM connector. Remove this connector by
pushing the tab inwards and pulling it outwards.
5
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2015+ Colorado & Canyon All Lights Mod Installation
Step 3:
Utilizing the T-taps provided, attach one to the
corresponding wire found in slot 13. Make sure
to completely close the T-taps for a proper
connection.
If your unfamiliar with T-taps, Click Here for
additional instructions.
Step 4
Utilizing the T-taps provided, attach one to
the corresponding wire found in slot 18. For
additional leverage, pliers can be used to close
T-taps.
If your unfamiliar with T-taps, Click Here for
additional instructions.
2015+ Colorado & Canyon All Lights Mod Installation
6
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
GM All Lights Mod Installation
Step 5:
Once both T-taps are installed, find the blue
marked end on the module. The marked end
needs to be plugged into the T-Tap on the wire
in pin 13.
Proceed to bend the Flexible module to
connect the other T-tap. If your unfamiliar with
quick disconnects, Click Here for additional
instructions.
Step 6:
Lastly, reinstall the connector into the BCM.
A click sound will be heard confirming the
connector has been fully inserted.
Disclaimer:
Make sure that the BLUEBLUE marked
side connects to the wire tapped
into pin 13.
7
Boost Auto Parts • 765-831-2830 • www.boostautoparts.com
2015+ Colorado & Canyon All Lights Mod Installation
If you experience any difficulties or
complications during your install, feel free to
reach out to our Technical Support Team.
Support@boostautoparts.com
765-831-2830
Your GM All Lights Mod Install is Complete!
/