Midmark 10546500 User guide

Brand: Midmark

Model: 10546500

Type: User guide

Midmark 10546500, part of the ClassicSeries™ Wet-Ring Vacuums, is a reliable and efficient dental vacuum system designed to maintain a clean and hygienic dental operatory. With its powerful suction capabilities, it effectively removes fluids and debris during dental procedures, ensuring a safe and comfortable environment for both patients and dental professionals.

Maintenance Kits

Mineral Reducer Kit

Order #: AVA8200

Includes:

• Installation instructions, housing,

cartridge, all necessary mounting

and installation hardware.

Order #: PFM8200

Includes:

• Cartridge for Mineral Reducer.

ADP

Vacuum Relief Valve Filter

Order #: 62935601

Includes:

• Filter

Vacuum Inlet Strainer

Order #:

Single Models - 62937301

Twin Models - 77005155

Includes:

• Filter bowl, screen and o-ring.

Dispos-A-Bowl

Order #:

Single Models - 77005167

Twin Models - 77005168

Includes:

• Container, lid and red safety tape.

Exhaust Silencer

Order #: 77000040

Includes:

• Single Vacs Only

Accessories

Vacuum

Inlet

Strainer

Water

Inlet

Strainer

Water

By-Pass

Valve In

Open

Position

Recycler

Models

Non-Recycler

Models

For Recycler To Be

Activated

During Normal

Operation The Water

By-Pass Valve Should

Be In the CLOSED

postion.

Recycler

Models

CLOSED Position

Shown

Note - Recycler Models Only

If you have low to no suction due to a clog by residue building up over time, there is a feature on vacuum to keep

it running until a service technician can troubleshoot the problem. Turn the water by-pass valve to the OPEN

position. This will by-pass the recycler and may keep the pump running.

Daily

A. Clean Vacuum Piping System.

Clean piping system with a non-foaming vacuum

system cleaner. Midmark recommends

Precision Clense™, Order No. 77000570.

 Note:ForthersttwoweeksofusingPrecision 

 Clense,ushlinesatthebeginningofthedaywith

 waterandchecktrapstwiceaday.Afterthersttwo

 weeks,ushwithwaterandchecktrapsasneeded.

1) Start with the furthest operatory from the vacuum.

2) Suction cleaning solution.

(Follow mixture instructions provided with the

vacuum system cleaner.)

Note: Alternate air and vacuum while cleansing;

submerge and remove HVE and SE from mixture

several times until mixture is consumed.

3) Keep the cleansed vacuum lines (HVE and SE)

open and move to the next operatory.

4) Repeat steps 1-3 until all vacuum lines are

cleansed.

B. Clean Vacuum Inlet Strainer.

Turn vacuum “OFF”. Remove, replace and or clean

 lterbowl,screenandgasket.Reassemble.Turn

vacuum “ON”.

Annually

A. Clean and or Replace Vacuum Relief

Filter.

Pulllteroutofendcap.Blowolterandor

 replaceifdamaged.ReplacelterinVRVendcap.

B. Clean Water Inlet Strainer.

Turn vacuum “OFF”. Remove cap on “Y” strainer

housing and pull out the wire intake strainer.

 Rinsewithwaterandblowo.Replacestrainer

and cap. Turn vacuum “ON”.

C. Clean / Dust Vacuum Pump(s).

Wipe with a clean cloth to remove dust and debris.

Equipment Alert

Scavenging polishing paste with

abrasives, running the pump with

no water supplied, using water with high mineral

content, or water with excessive sediment can

damage or reduce the lifespan of the pump and is

not considered a defect in material or workmanship.

10546500 Rev FA3 (8/18/21)

Style D

Care Guide

To ensure years of reliable service, follow the

maintenance schedule outlined in this guide.

If service is required, contact your authorized

Midmark dealer.

Dealer (name / phone):

__________________________________

Model Number: __________________

Serial Number: __________________

Date of Purchase: _________________

Annual Maintenance Log

Date: Services Performed: Technician:

_____ _______________________ __________

Classic Series®

Wet-Ring Vacuums

LIMITED WARRANTY

SCOPE OF WARRANTY

Midmark Corporation (“Midmark”) warrants to the original

purchaser its new ClassicSeries™ products and com-

ponents (except for components not warranted under

“Exclusions”) manufactured by Midmark to be free from

defects in material and workmanship under normal use

and service. Midmark’s obligation under this warranty

is limited to the repair or replacement, at Midmark’s op-

tion, of the parts or the products the defects of which are

reported to Midmark within the applicable warranty period

and which, upon examination by Midmark, prove to be

defective.

APPLICABLE WARRANTY PERIOD

The applicable warranty period, measured from the date

of installation for the original user, shall be:

• ClassicSeries™ Wet Ring Vacuums: Five (5) years

or 10,000 usage hours (whichever comes rst)

EXCLUSIONS

This warranty does not cover and Midmark shall not be

liable for the following: (1) repairs and replacements be-

cause of misuse, abuse, negligence, alteration, accident,

freight damage, or tampering; (2) products which are

not installed, used and properly cleaned as required in

the Midmark “Installation” manual and or “maintenance”

guide for this applicable product; (3) products considered

to be of a consumable nature; (4) accessories or parts

not manufactured by Midmark; (5) charges by anyone

for adjustments, repairs, replacement parts, installation,

or other work performed upon or in connection with such

products which is not expressly authorized in writing in

advance by Midmark.

EXCLUSIVE REMEDY

Midmark’s only obligation under this warranty is the re-

pair or replacement of defective parts. Midmark shall not

be liable for any direct, special, indirect, incidental, exem-

plary, or consequential damages or delay, including, but

not limited to, damages for loss of prots or loss of use.

NO AUTHORIZATION

No person or rm is authorized to create for Midmark any

other obligation or liability in connection with the prod-

ucts.

THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND

IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF

ANY KIND INCLUDING ANY WARRANTIES OF MERCHANT-

ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

THIS WARRANTY IS LIMITED TO THE REPAIR OR RE-

PLACEMENT OF DEFECTIVE PARTS.

Vacuum Relief Valve Filter

Pull lter out of Vacuum Relief

Valve end cap to clean or replace.

Single Model

Twin Model

A. Rotate barrel clockwise to increase

“Hg.

B. Rotate barrel counterclockwise to

decrease “Hg.

Vacuum Level Adjustment

Procedure

VRV Location

Twin Model

Increase “Hg

Decrease “Hg

Note: Vacuum Relief Valve is factory set at 10” Hg.

Perform “Vacuum Level Adjustment” Procedure if

adjustment is needed. Never adjust the VRV above

12” Hg on the vacuum gauge.

Midmark 10546500 User guide

Midmark 10546500 User guide

Midmark 10546500 User guide

Related papers