Tektronix TDS3054C User manual

xx

TDS3000C Series

Digital Phosphor Oscilloscopes

ZZZ

User Manual

*P071230807*

071-2308-07

TDS3000C Series

Digital Phosphor Oscil

loscopes

ZZZ

User Manual

xx

Last Published: May 7, 2015

REPRODUCTION AND DISTRIBUTION

OF THIS TECHNICAL MANUAL IS

AUTHORIZED FOR UNITED STATES OF

AMERICA GOVERNMENT PURPOSES.

www.tektronix.com

071-2308-07

served. Licensed software products are

owned b y Tektronix or its subsid iaries or suppliers, and are protected by national

copyright laws and international t reaty provisions.

Tektronix products are covered by U .S. and foreign patents, issued and pen din g.

Information in this publication supersedes that in all previously published

material. Speciﬁcations and p

rice change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

TEKPROBE, and TekSecure are registered trademarks of Tektronix, Inc.

DPX, WaveAlert, e*Scope

, and OpenChoice are trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14150 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For p ro duct information, sales, service, and technical support:

In North America, call 1-800-83 3-920 0.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Warranty

Tektronix warrants that the produc

t will be free from defects in materials and workmanship

for a period of three (3) years from the date of original purchase from an authorized

Tektronix distributor. If the

product p roves defective during this warranty period,

Tektronix, at its option, either will repair the defective product without charge for parts

and labor, or will provide a re

placement in exchange for the defective product. Batteries

are excluded from this warranty. Parts, modules and replacement products used by

Tektronix for warranty work

may be new or reconditioned to like new performance. All

replaced parts, modules and products becom e the property of Tektronix.

In order to obtain service under this warranty, Customer m ust notify Tektronix of the

defect before the expiration of the warranty period and make suitable arrangements for the

performance of service. Customer shall be responsible for packaging and shipping the

defective product to the service center designated by Tektronix, shipping charges prepaid,

and with a copy of customer proof of purchase. Tektronix shall pay for the return of the

product to Customer if the shipme nt is to a location within the country in which the

Tektronix service center is located. Customer shall be responsible for paying all shipping

charges, duties, taxes, and a ny other charges for products returned to any o ther locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or

improper or inadequate maintenance and care. Tektronix shall not be obligated to furnish

service under this warranty a) to repair damage resulting from attempts by personnel other

than Tektronix representatives to install, repair or service the product; b) to repair damage

resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a

product that has been modiﬁ ed or integrated with other products when the effect of such

modiﬁcation or integration increases the time or difﬁculty of servicing the product.

THIS WARR

ANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE

PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED.

TEKTRON

IX AND ITS VENDORS D ISCLAIM ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX'

RESPON

SIBILITY TO REPAIR OR REPLACE DEFECTIVE PRO DUCTS IS THE

SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR

BREAC

H OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE

LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL

DAM

AGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS

ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

[W16 – 15AUG04]

Table of Contents

Important safety information ........................................... iv

General safety summary ........................................... iv

Service safety summary.......................................... viii

Terms in this manual ............................................... ix

Symbols and terms on the product................................ ix

Compliance information ................................................ xi

EMC compliance................................................... xi

Safety compliance................................................ xiii

Environmental considerations................................... xvi

Preface.................................................................. xix

Getting Started............................................................ 1

Initial Setup .......................................................... 1

Product and Feature Description................................... 5

Operating Positions ................................................. 9

Connecting Power................................................. 10

Installing an Application Module ................................ 15

Installing the Communication Module .......................... 15

Front-Panel Menus and Controls................................. 16

Front-Panel Connectors........................................... 28

Rear-Panel Connectors............................................ 29

Communication Module Connectors ............................ 30

Application Examples.................................................. 31

Taking Simple Measurements.................................... 32

Analyzing Signal Detail .......................................... 38

Taking FFT Measurements ....................................... 45

Triggering on a Video Signal..................................... 48

Capturing a Single-Shot Signal .................................. 51

Saving Data to a USB Flash Drive............................... 54

Reference................................................................ 59

Acquisition Controls .............................................. 59

Cursor .............................................................. 70

Di

splay ............................................................. 75

TDS3000C Series O scilloscope User Manual i

Table of Con tents

Hard Copy ......................................................... 78

Horizontal Controls ............................................... 81

Math and FFT...................................................... 87

Measure ............................................................ 96

QuickMenu ....................................................... 101

Save/Recall ........... . . . . . . ......... . . . ............ . . . . . . ........ 102

Trigger Controls .................................................. 109

Utility.............................................................. 133

Vertical Controls.................................................. 140

e*Scope Web-Based Remote Control .......................... 144

Appendix A: Speciﬁ cations........................................... 149

Appendix B: Factory Setup........................................... 161

Appendix C: Accessories ....... . . . ......... . . . ......... . . . ......... . . 165

Appendix D: Probe Basics............................................ 169

Probe Descriptions ............................................... 169

Probe Compensation ............................................. 170

TekProbe Interface ............................................... 171

Probe Guard ...................................................... 171

Ground Leads..................................................... 172

P3010 High-Frequency Compensation ......................... 173

P3010 Replaceable Parts and Accessories .... . . . . . . ........... 174

P6139A Replaceable Parts and Accessories .. . . . ......... . . . .. 175

Using Other Probes .............................................. 177

Supported Active Probes and Adapters......................... 177

Unsupported Probes.............................................. 178

Appendix E: General Care and Cleaning............................ 179

Appendix F: Ethernet Setup .......................................... 181

Your Ethernet Network Information ............................ 181

Entering the Ethernet Network Settings........................ 182

Entering the Network Printer Settings.......................... 183

Testing Your Ethernet Connection .............................. 184

Troubleshooting Your Ethernet Connection.................... 185

The Instrument Setup Screen.................................... 187

The Printer Conﬁguration Screen ............................... 188

The Add Printer Screen.......................................... 189

ii TDS3000C Series Oscilloscope User Manual

Table of C on tents

Ethernet Error Messages......................................... 191

Ethernet Settings Form........................................... 192

Index

TDS3000C Series O scilloscope User Manual iii

Important safety information

This m anu al contains information and w a rnings that must be fo llo wed

by the user for safe operation and to keep the product in a safe condition.

To safely perform service on this prod uct, additional info rm a tion

is provid ed at the end of this section . (See page viii, Service safety

summary.)

General safety summary

Use the product o nly as speciﬁed. Review the following s afety

precautions to avoid injury and prevent dam age to this product or any

products connected to it. Carefully read all instructions. Retain these

instructions for future reference.

Comply with local and national safety codes.

For correct and safe operatio n of the product, it is essential that you

follow generally accepted safety procedures in addition to the safety

precautions speciﬁed in this manual.

The product is designed to be used by trained personnel only.

Only qualiﬁed personnel who are aware of the hazards involved should

remove the cover for repair, maintenance, or adjustment.

Before use, always check the product with a known source t o be sure it

is oper a ting corr ectly.

This product is not intended for detection of h azardous voltages.

Use personal protective equipment to prevent shock and arc blast injury

where hazardous live conductors are exposed.

When inco rporating this equipment into a system, the safety of that

system is the responsibility of the assembler of the system.

To avoid ﬁre or personal injury

Use proper power cord. Use only the pow er cord speciﬁed for this

product and certiﬁed for the country of u se.

Do not use the provided power cord for other products.

iv TDS3000C Series Oscilloscope User Manual

Important safety information

Ground the product. This product is grounded through the grounding

conductor of the power cord. To avoid electric sh ock, the grounding

conductor must be connected to earth ground. B efore making

connections to the input or output terminals of the produ ct, make sure

that the product is properly grounded.

Do not disable the power cord grounding connection.

Power disconnect. The p ower cord disconnects the produ ct from the

power source. See instructions for the location. Do not position the

equipmentsothatitisdifﬁcult to operate the power cord; it m ust remain

accessible to the user at all times to allow f or quick d isconnection if

needed.

Connect and dis conn ect properly. Do not con nect or disconnect probes

or test leads while they are connected to a voltage source.

Use only insulated voltage probes, test leads, and adapters supplied with

the pro duct, or indicated by Tektron ix to be suitable for the product.

Observe all terminal ratings. To avoid ﬁ re or shock hazard, observe all

ratings and markings on the product. Consult the product manual for

further ratings inform ation before making connections to the product.

Do not exceed the Measurement Category (CAT) rating and voltage or

current rating of the lowest rated individual comp onen t of a product,

probe, or accessory. Use caution when using 1:1 test leads because the

probe tip voltage is directly transmitted to the product.

Do not apply a poten tial t o any terminal, including the common

terminal, that exceeds the m aximum rating of that terminal.

Do not ﬂoat th e common terminal above the rated voltage for that

terminal.

The measuring terminals on this product are not rated for connection

to mains Category III or IV circuits, or t o mains Category II circuits

greater than 100 V.

When connected to circuits other than mains, the maximum transient

overvoltage rating is 400 V peak."

Do not operate without cove rs. Do n ot operate this product with covers

or panels removed, or with the case open. Hazardous v oltage exposure

is possible.

TDS3000C Series O scilloscope User Manual v

Important safety information

Avoid exposed circuitry. D o not touch exposed connections and

components when power is present.

Do not operate with suspected fa

ilures.

If you suspect that there is damage

to this product, have it inspected by qualiﬁed service p ersonnel.

Disable the product if it is da

maged. Do not use the product if it is

damaged or operates incorrectly. If in doubt ab out safety of the product,

turn it off and disconnect the power cord. Clearly mark the product to

prevent its further operati

on.

Before use, inspect voltage probes, test leads, and accessories for

mechanical damage and re

place when damaged. Do not use probes o r

test leads if they are damaged, if there is exposed metal, or if a wear

indicator shows.

Examine the exterior of the product before you use it. Lo ok for cracks

or missing pieces.

Use only speciﬁed replacement p arts.

Use proper fuse. Use only the fuse type and rating speciﬁed for this

product.

Do not operate in wet/damp conditions. Be aware that condensation may

occurifaunit

is moved fro m a cold to a warm environment.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

Remove the input signals before

you clean t

he produ ct.

Provide proper ventilation. Refer to the installation instructions in the

manual for details on installing the product so it has proper ventilation.

Slots and open ing s are provided for ventilation and shou ld never be

covered or otherwise obstructed. Do no t push ob jects into any of the

openings.

Provide a safe working environment. Always place the product in a

loca

tion conv enien t for viewing the display an d indicators.

vi TDS3000C Series Oscilloscope User Manual

Important safety information

Avoid improper or prolo nged use of keyboard s, pointers, and button

pads. Improper or prolonged keyboard or pointer use may result in

serious injury.

Be sure your work area meets applicable ergonomic standards. Consult

with an ergonomics professional to avoid stress injuries.

Probes and test leads

Before connecting probes or test l eads, connect the power cord from the

power connector to a properly grounded power outlet.

Keep ﬁngers behind the ﬁnger guards on the probes.

Remove all probes, test leads and accessories that are n ot in use.

Use only correct Measurement Category (CAT), voltage, temperature,

altitude, and amperage rated probes, test leads, and adapters for any

measurement.

Beware of high voltages. Understand the voltage ratin gs fo r the probe

you are using and do not exceed those ratings. Tw o ratings are i mportant

to know and u nderstand :

The maximum measu rem ent v oltage from the probe tip to the probe

reference lead.

The maximum ﬂoating voltage f ro m the probe refer e nce lead to

earth ground

These two voltage ratings depend on the probe and your application.

Refer to the Speciﬁcations section of th e manual for more information.

WARNING. To prevent electrical shock, do not exceed the maximum

measurement or m a ximum ﬂoating voltage for the oscilloscope input BNC

connector, probe tip, or probe reference lead.

Connect a nd disconnect properly. Conn ect the probe output to the

measurement product before connecting the probe to the circuit under

test. Connect the probe reference lead to th e circuit under test before

connecting the probe input. Disconnect the probe input and the p robe

reference lead from the circuit under test before disconnecting the probe

from the measurement p roduct.

TDS3000C Series O scilloscope User Manual vii

Important safety information

Connect and disconnect properly. De-energize the circuit under test

before connecting or disconnecting the current probe.

Connect the probe reference l ead to earth ground only.

Do not connect a current probe to any wire that carries voltages above

the current probe voltage ratin g.

Inspect the pro be and accessories. Before each use, inspect probe

and accessories for damage (cuts, tears, or defects in the probe body,

accessories, o r cable jacket). Do not use if damaged.

Ground-referenced oscilloscope use . Do not ﬂoat the reference lead

of this probe when using with ground-referenced oscilloscopes. The

reference lead must be connected to earth potential (0 V).

Floating meas urement use. Do not ﬂoat the reference lead of this probe

above the rated ﬂoat voltage.

Service s afety summary

The Service safety summary section contains additional information

required to safely perform service on the product. Only qualiﬁed

personnel should perform s erv ice procedures. Read this Service safety

summary and t he General safety summary before performing any

service procedures.

To avoid electric shock. Do not touch exposed connections.

Do not service alone. Do not perform internal service or a dju st ments of

this product unless another person capable of rendering ﬁrst aid and

resuscitation is presen t.

Disconnect power. To avoid electric shock, switch off the product power

and disconnect the power cord from the m ains power before removing

any covers or panels, or opening the case fo r servicing.

Use care when servicing with power on. Dangerous voltages or currents

may exist in this product. Disconnect pow er, remove b a ttery (if

applicable), and d isconnect test leads before removing protective panels,

soldering, or replacing components.

viii TDS3000C Series Oscilloscope User Manual

Important safety information

Verify safety after repair. Always recheck ground continuity and mains

dielectric strength after performing a repair.

Terms in this manual

These terms may appear in this manual:

WARNING. Warning statements iden tify conditions or practices that c ould

result in injury or loss of life.

CAUTION. Caution sta tements identify conditions or practices that could

result in damage to this product or other property.

Symbols and terms on the product

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you

read the marking.

WARN ING indicates an injury hazard not imm ediately accessible

as you read the m arking.

CAUTION indicates a hazard to property including the product.

When this symbol is marked on the product, be sure to consult

the manual to ﬁnd out the nature of the potential hazards and

any actions which have to be take n t o avoid them. (This symbol

may also be used to refer the user to ratings in the manual.)

The following symbol(s) may appear on the product:

TDS3000C Series O scilloscope User Manual ix

Important safety information

x TDS3000C Series Oscilloscope User Manual

Compliance information

This section lists the E M C (ele

ctromagnetic compliance), safety, and

environmental standards with which the instrument complies.

EMC compliance

EC Declaration of Conformity – EMC

Meets intent of D irective 2004/108/EC for Electromagnetic

Compatibility. Com pliance was demonstrated to the following

speciﬁcations as listed in the O fﬁcial Journal of the European

Communit ies:

EN 61326-1:2006, EN 61326-2-1:2006. EM C r equirem ents for electrical

equipment for measurement, control, and laboratory use.

123

CISPR 11:2003. Radiated and conducted emissions, Group 1,

Class A

IEC 61000-4-2:2001. Electrostatic discharge imm unity

IEC 61 000-4-3:2002. RF elec

tromagnetic ﬁeld immunity

4

IEC 610 00-4-4:2 004 . Electrical fast transient/burst immunity

IEC 61000-4-5:2001. Power line surge immunity

IEC 61000-4-6:2003. Conducted RF immunity

5

IEC 6100 0-4-11:2004. Voltage dips and interruptions immunity

6

EN 61000-3-2:2006. AC power line harmonic em issions

EN 61000-3-3:19 95. Voltage changes, ﬂuctuations, and ﬂicker

European contact.

Tektronix UK, Ltd.

Western Peninsula

Western Road

Bracknell, RG12 1RF

TDS3000C Series O scilloscope User Manual xi

Compliance information

United Kingdom

1

This product is intended for use in nonresidential areas only. Use in residential areas

may cause electromagnetic interference.

2

Emissions which exceed the levels required by this standard may occur when this

equipment is connected to a test object.

3

For compliance with the EMC sta nd

ards listed here, high quality shielded interface

cables should be used.

4

The increase in trace noise while subjected to a test ﬁeld (3 V/m over the frequency

range 80 MHz to 1 GHz, 1.4 GHz to 2.0 GHZ and 1 V/m from 2.0 GHz to 2.7 GHz, with

80% amplitude modulation at 1 k

Hz) is not to exceed 3 major divisions peak-to-peak

at 5 mV/div and higher.l

5

The increase in trace noise while subjected to a test ﬁeld (3 V/rms over the frequency

range 150 kHz to 80 MHz, with 80% amplitude modulation at 1 kHz) is not to exceed 2

major divisions peak-to-pe a

k at 5 mV/div and h igher.

6

Performance C riterion C applied at the 70%/25 cycle Voltage-Dip and the 0%/250 cycle

Voltage-Interruption test levels (IEC 61000-4-11).

Australia / New Zealand De

claration of Conformity – EMC

Complies with the EMC provision of the Radiocommunications Act per

the f ollowing standard,

in accordance with ACMA:

CISPR 11:2003. Radiated an d Conducted Em issio ns, Group

1, Class A , in accorda

nce with EN 61326-1:2006 and

EN 613 26-2-1:2 006 .

Australia / New Zealand contact.

Baker & McKenzie

Level 27, AMP Centre

50 Bridge Street

Sydney NSW 2000, A ustralia

FCC – EMC

Exempt from FCC 47 CFR Part 15, Subpart B, Class A

xii TDS3000C Series Oscilloscope User Manual

Compliance inform ation

Safety compliance

This section l ists the safety s tandards with which the product complies

and other safety comp liance information.

EU declaration of conformity – low voltage

Compliance was demonstrated to the following speciﬁcation as listed

in the Ofﬁcial Journal of the European Union:

Low Voltage Directive 2006/95/EC.

EN 61010-1. Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use – Part 1: General

Requirements.

EN 61010-2-030. Safety Requirements for Electrical Equipment

for M easurement, C ontrol, and Laboratory Use – Part 2-030:

Particular requirements for testing and m easuring circuits.

U.S. nationally recognized testing laboratory listing

UL 61010-1. Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use – Part 1: General

Requirements.

UL 61010-2-030. Safety Requirements for Electrical Equipment

for M easurement, C ontrol, and Laboratory Use – Part 2-030:

Particular requirements for testing and m easuring circuits.

Canadian certiﬁcation

CAN/CSA-C22.2 No. 61010-1. Safety R equirem ents for Electrical

Equipment for Measurement, Control, and Laboratory Use – Part 1:

General Requirements.

CAN/CSA-C22.2 No. 61010-2-0 30. Safety Requirements for

Electrical Equipment for Measurem ent, C ontrol, and Laboratory

Use – Part 2-030: Particular requirements for testing an d measuring

circuits.

TDS3000C Series O scilloscope User Manual xiii

Compliance information

Additional compliances

IEC 61010-1. Safety Requirements for Electrical Equipment for

Measurement, Control, and Laboratory Use – Part 1: General

Requirements.

IEC 61010-2-030. Safety Requirements for Electrical Equipment

for M easurement, Control, and Laboratory Use – Part 2-030:

Particular requirements for testing and measuring circuits.

Equipment type

Test and measuring equipment.

Safety class

Class 1 – grounded product.

Pollution degree descriptions

A measure of the contaminants that could occur in the environment

around a nd within a product. Typically the internal environment inside

a product is considered to be the same as the external. Pro ducts should

be used only in the environment for which they are rated.

Pollution degree 1. No pollution or only dry, nonconductive

pollution occurs. Products in this category are generally

encapsulated, hermetically sealed, or located in clean rooms.

Pollution deg ree 2. Norm a ll y only dry, nonconductive pollution

occurs. Occasionally a temporary conductivity that is caused

by condensation must be expected. This location is a typical

ofﬁce/home environm ent. Temporary condensatio n occurs only

when the product is out of service.

Pollution degree 3. Con ductive p ollution, o r dry, nonconductive

pollution that becomes conductive due to condensation. These

are sheltered locations where neither temperature nor humidity

is controlled. The area is protected from direct su nshin e, rain, or

direct wind.

Pollution degree 4. Pollution that generates persistent con ductivity

through con ductive dust, rain, or snow. Ty pical outdoor locatio ns.

xiv TDS3000C Series Oscilloscope User Manual

Page is loading ...

Tektronix TDS3054C User manual

This manual is also suitable for

Tektronix TDS3054C User manual

Related papers

Other documents