Simplicity EDGER GE254 User manual

VICTA

GE254 Edger

Assembly and

Owner’s Manual

WARNING! Read this manual before operating your VICTA Edger.

Not for

Reproduction

IMPORTANT INFORMATION

OIL WARNING

Congratulations on your purchase of a top quality Victa Edger. This instruction manual will aid in

the assembly, operation and maintenance of your new Edger.

Please read carefully to ensure safety and the long life of your product.

Do not operate the unit before reading this manual!

Keep this instruction manual in a safe place for future reference or if service is required on your unit.

Please read the ‘Warranty’ section carefully

• Briggs & Stratton 550 Engine must have 600ml off S.A.E. 30

Oil placed in the Sump Before starting

NOTE: Failure to comply with the following

instructions will result in engine damage

that is not covered by product warranty.

Not for

Reproduction

Features 1

Unit Features

Safety & Handling 2

Safety Instructions

Hazards

Personal Safety Equipment

Assembly Procedures 5

Unit Details

Wheel Assembly

Handle Assembly

Operating Instructions 10

Operating the Edger

Edging Tips

Starting the Edger

Bail Engagement

Maintenance & Care 13

Cleaning

Belt

Adjustment

Engine Components

Oil Change

Air Filter replacement

Spark Plug Replacement

Maintenance Chart

Questions & Answers 22

Troubleshooting

Accessories & Spare Parts 23

Victa Products

Warranty 24

Warranty Conditions

Table of Contents

CONTENTS

&

SYMBOLS

Not for

Reproduction

FEATURES

1

Cutting Blade guide

Dual fold handle for

compact storage

Easy to manoeuvre

wheel design

Tilt adjustment for garden

edge maintenance

Operator presence bail

for user safety engagment

Ergonomically position

starter cord

Oil Filler Cap

Fuel Tank

Control Bail

Front Roller Rear Wheel

Mu r

Blade

Blade Guard

Exhaust

WARNING

HOT - DO NO T

TOUCH WHEN IN USE

OR AFTER STOPING! Fuel Cap

Lower Handl

e

Spark Plug

Upper Handle

Control Cable

Centre Handle

ON/OFF Switch

Locking Levers

Not for

Reproduction

2

Safety Instructions

Transporting the Edger

s 4URNTHEENGINEOFFBYMOVINGTHE"ON - OFF" switch to the "OFF" position and then

turn the fuel tap to the "OFF" position.

s $ISCONNECTTHESPARKPLUGLEAD

s $ONOTTRANSPORTTHE%DGERINAVEHICLEIFTHEREISFUELINTHEFUELTANK

Before using the Edger

• For the Briggs and Stratton 550 engine 600ml of S.A.E 30 oil must be placed in

engine sump before starting engine. Failure to do so will cause engine damage

and will void engine warranty.

s $ONOTSTARTTHE%DGERUNTILYOUHAVESTUDIEDTHEINSTRUCTIONMANUAL

s +NOWTHE%DGERCONTROLSANDLEARNHOWTOSTOPTHEENGINEQUICKLYINANEMERGENCYBY

moving the "ON - OFF" switch to the "OFF" position.

s "EFOREUSINGTHE%DGERENSURETHECUTTINGBLADEASSEMBLYISNOTWORNORDAMAGED

Always replace worn or damaged blade and blade nut.

Note: Damaged or worn blade and blade nut are major hazards.

Use genuine Victa spare parts only.

s #HECKALLFASTENERSANDGUARDSREGULARLY!LWAYSENSURETHE%DGERISINASAFEOPERATING

condition.

s #HECKFORGRASSBUILDUPAROUNDTHEENGINEANDMUFFLERWHICHMAYCAUSEOVERHEATINGOR

become a fire hazard.

s $ONOTSTARTTHEENGINEUNLESSTHEBLADEGUARDISSECURELYINPOSITION

s2EPLACEBLADEGUARDIFWORNORDAMAGED

Operating the Edger

s $ONOTUSEWHILEPEOPLEORPETSAREINTHEVICINITYOFTHE%DGERORWITHINTHEOPERATING

area. Ensure that bystanders are a minimum of 15 metres away.

s $ONOTOPERATE%DGERINBAREFEETOROPENSHOES!LWAYS7EARLONGTROUSERSANDHEAVY

footwear.

s -AKESURETHEOPERATINGAREAISCLEAROFSTICKSSTONESBONESWIRESTRINGGLASS

nails and debris before use. Objects could be thrown by the blade and cause injury or

damage.

s 3TARTTHEENGINECAREFULLYWITHFEETWELLCLEAROFBLADES$ONOTTILTTHE%DGERWHENSTARTING

the engine.

s 3TOPTHEENGINEIFYOULEAVETHE%DGERUNATTENDED

SAFETY

&

HANDLING

Not for

Reproduction

3

s /PERATEONLYINGOODDAYLIGHT

s +EEPHANDSANDFEETAWAYFROMrotating parts beneath Edger when the engine is running.

s $ONOTOVERSPEEDTHEENGINEORALTERTHEGOVERNORSETTINGS%XCESSIVEENGINESPEEDIS

dangerous and shortens engine life.

s Never lift or carry the Edger when the engine is running.

s 3TOPTHEENGINEBEFOREPUSHINGTHE%DGERACROSSGRAVELPATHSORROADS

s 3TOPTHEENGINEBEFOREADJUSTINGTHECUTTINGDEPTH

s 5SEEXTREMECAUTIONWHENCHANGINGDIRECTIONONASLOPE

s .EVERPULLTHE%DGERTOWARDSYOU(Do Not Reverse) You may slip and pull the machine on

top of your feet.

s 7ALKWITHTHE%DGERNEVERRUN

s !TTHECONCLUSIONOFUSERELEASECONTROLBAILANDWAITFORTHECUTTINGBLADETOSTOPTHEN

turn the engine and fuel tap off.

s!LWAYSSTARTTHEENGINEONFLATLEVELGROUND

s.EVERLEAVETHEUNITUNATTENDEDWHENINUSE

s$ONOTLEAVETHE%DGERIDLINGFORLONGPERIODS

(Turn unit off if not in use for longer than 5 minutes)

s$ONOTSTARTTHE%DGERINAELEVATEDPOSITION(Above ground Level)

Maintaining the Edger

s )FTHE%DGERBEGINSTOVIBRATEABNORMALLYORIFITSTRIKESAFOREIGNOBJECT34/0THEENGINE

disconnect the spark plug lead from the spark plug and inspect the Edger blade and guard

for any damage.

s 2EPLACEWORNORFAULTYMUFFLERASTHISWILLADVERSELYAFFECTENGINEPERFORMANCEANDINCREASE

emissions.

s 6ICTARECOMMENDSTHATALLMAINTENANCEREPAIRANDINSPECTIONWORKBECARRIEDOUTBYA

Victa Authorised Service Centre.

s 3TORETHE%DGERINAWELLVENTILATEDAREAAWAYFROMANYNAKEDFLAMESSUCHASTHOSEFOUND

in gas hot water heaters.

Refuelling the Edger

s 2EFUELTHE%DGEROUTDOORSONLY(The engine must be stopped)

sNote: Ensure the fuel filter is clean and Replace if punctured or damaged!

s $ONOTSMOKEWHENREFUELLINGTHEENGINE

.EVERADDFUELORREMOVETHEFUELCAPWHENOPERATINGTHEENGINEs

If fuel is spilt, s Never start the engine! Move the Edger away from the area of the spill.

Always clean fuel spills immediately.s

)FAFUELSPILLOCCURS$ONOTCREATEANYSOURCEOFIGNITIONUNTILFUELVAPOURSHAVEDISSIPATEDs

from the area of the spill.

s !LWAYSSTOREFUELINACOOLDRYAREAANDONLYUSEACONTAINERSPECIFICALLYDESIGNEDFORTHE

PURPOSEOFHOLDINGFUEL6ICTASUPPLIESALITREFUELCANASANOPTIONALEXTRA

Note: Plastic containers are unsuitable for fuel storage, except those specifically

designed to hold fuel.

THE EDGER IS INTENDED FOR CUTTING LAWN EDGES ONLY!

DO NOT USE FOR CUTTING WOOD OR STUMP GRINDING!

Safety instructions

SAFETY

&

HANDLING

Not for

Reproduction

4

The following safety precautions must be strictly observed to avoid the risk of damage or personal

injury.

s#HECKALLFASTENERSREGULARLY!LWAYSENSURETHATTHE%DGERISINSAFEOPERATINGCONDITION

s$ONOTOPERATETHE%DGERINCONFINEDSPACESWHEREEXHAUSTFUMESCARBONMONOXIDECAN

collect.

s3TOPTHEENGINEWHENEVERYOULEAVETHE%DGER

s.EVERTRYTOCLEARGRASSFROMTHE%DGERWHILETHEENGINEISRUNNING

s.EVERLIFTORCARRYTHE%DGERWHENTHEENGINEISRUNNING

s"YSTANDERSMUSTBEATLEASTMETRESAWAYDURINGOPERATIONOFTHE%DGERASROCKSANDOTHER

materials may be thrown at high velocities.

s .EVERUSETHE%DGERUNLESSTHEGUARDSSUPPLIEDBY6ICTAAREFITTEDCORRECTLYANDINGOODORDER.

Hazards

A pair of Gloves

Personal Safety Equipment

Recommended safety equipment to wear when working with your Edger

MUFFLER & EXHAUST HOT

DO NOT TOUCH WHEN IN USE

OR AFTER STOPING!

SAFE - ZONE•

/PERATION0OSITION/NLYOPERATEBAIL

push & tilt in this position.

Turn off engine in all other Zones.

START & RE-FUEL ZONE•

Start, refuel & adjust height in this

position only.

!,7!93452./&&%.').%).

4()30/3)4)/.

$/./4PUSHTILTOROPERATEBAIL

in this position.

DANGER - ZONE•

$/./4/0%2!4%!.9

&5.#4)/.).4()30/3)4)/.

Engine must be off when in this position.

Do not tilt or lift the unit in this position.

Remove spark plug when performing maintenance.

A set of ear muffs Eye protection A pair of safety boots

NOTE: We recommend gloves are to be worn when any maintenance is performed!

E

S

A

F

E

-

Z

O

N

E

S

T

A

R

T

I

N

G

&

R

E

-

F

U

E

L

I

N

G

Z

O

N

D

A

N

G

E

R

-

Z

O

N

E

SAFETY

&

HANDLING

Not for

Reproduction

ASSEMBLY PROCEDURES

5

Unit details

1. Edger chassis

Note: The chassis is connected to the upper handle by the control cable.

DO NOT DISCONNECT OR CHANGE THE CABLE SCREWS!

,OWERHANDLEX

#ENTREHANDLEX

4. Fastener pack

LOCKINGLEVERSX

KNOBSBOLTX

-SQUARENECKBOLTX

3ADDLEPLATESX

-NUTX

-WASHERSSMALLX

-WASHERSLARGEX

&RONTROLLERX

2EARWHEELX

-ANUAL.OTSHOWNX 2

3

5

6

1

4

x 2

x 4

x 2

x 6

x 2

x 4

Not for

Reproduction

ASSEMBLY PROCEDURES

Assembling the wheels

1. Remove edger and components from the carton.

Note: Remove the upper handle and place on the ground before lifting the Edger

chassis from the carton.

,OCATETHEMOUNTINGBRACKETTENSIONKNOBSX

-KNOBBOLTSXANDWASHERSX

3. Screw knobs and washers into the bracket.

&RONTWHEELMOUNTINGBRACKET

4. Repeat step 3 for the

2EARWHEELMOUNTINGBRACKET

5. Locate the rear wheel assembly post and insert into the right

rear wheel mounting bracket.

Adjust to the desired height & tighten knob firmly.

,OCATETHEFRONTROLLERASSEMBLYANDINSERTINTOTHEFRONTWHEEL

THEMOUNTINGBRACKET3ETTINGTHEHEIGHTOFBOTHROLLER

WHEELATFORSTARTINGANDSTORAGEISRECOMMENDED

Adjust to the desired height & tighten knob firmly.

Wheel assembly

WARNING!

TAKE CARE WHEN ADJUSTING

HEIGHT - KEEP FEET & HANDS

AWAY FROM UNDER EDGER

TO PREVENT STRIKING FROM

UNIT HEIGHT DROPPING.

WARNING! HAND & FINGER PINCH HAZARD

TAKE CARE & USE CAUTION WHEN ASSEMBLING

TO PREVENT PINCHING.

6

2.

3.

5.



x 2 x 2

Bracket

Knob

Washer

Not for

Reproduction

ASSEMBLY PROCEDURES

7

Your Edger should include a kit with the following parts.

When folding or unfolding the handles, ensure that the bail cable is

not caught, twisted, kinked or stretched!

Handle assembly

Assembling the handle

1. Insert the bolt through the hole, as shown.

The shoulder bolt should locate into the

deck.

2. Lower handle in position as shown, Place

one of the saddle plates onto the protruding

bolt.

Bolt

Handle

x 2

x 4

x 6

Not for

Reproduction

ASSEMBLY PROCEDURES

8

Handle assembly

Note: Ensure the control cable is not twisted,

pinched or damaged when assembling

the dual fold handle.

3. Thread one of the nuts onto the top of the

bolt and tighten with fingers. Then torque the

NUTTO.M-AXIMUM

4. Repeat steps 1 & 3 on the right side,

as shown.

5. Attach the dual fold centre handle

using the locking levers and nuts

provided. The locking levers should

be on the outside, as shown.

!TTACHTHEDUALFOLD5PPERHANDLE

using the locking levers and nuts

provided. The locking levers should

be on the outside, as shown.

.UT

.M 3.

5.



Not for

Reproduction

9

ASSEMBLY PROCEDURES

Before using the Edger read the safety instructions!

To avoid damage to the Edger, do not allow string or other material to

wrap around the blade or spindle. Stop the engine, disconnect spark plug

and remove material immediately if this occurs.

Handle assembly

Bail Cable Attachment

1. Remove the bail Tag. 2. Remove bail by springing hook

inwards.

3. Slide cable eyelet over bail hook. 4. Reinsert bail in handle holes

"cable side first".

Operating the Edger

1. 2.

3. 4.

9

R

EM

O

V

E

B

A

I

L

H

OO

K

S

IN

WA

R

D

S

B

A

IL

H

OO

K

T

HR

O

UG

H

EY

E

LET

R

E-IN

SE

C

A

B

L

ES

ID

E

H

OO

KF

IR

S

T

H

EN

R

E-IN

SE

R

T

OT

H

ER

H

OO

K

R

T

Not for

Reproduction

10

OPERATING INSTRUCTIONS

s4HE%DGERWILLCUTALONGFOOTPATHSDRIVEWAYSFLOWER

beds & similar areas.

s5SETHEYELLOWARROWGUIDEONTHEBLADEGUARDTO

align the blade with the edging surface.

Note: The guide will give approximate location of

the cutting blade only!

s#UTATASTEADYPACE)FTHEBLADEBEGINSTOBOG

down you are edging to fast, Slow your pace

"DO NOT FORCE" the blade into the ground.

s,IGHTCONTACTOFTHEBLADEAGAINSTTHEFOOTPATH

edge or curb is acceptable and will not damage the

edger.

s"ESTVISUALAPPEARANCEISOBTAINEDWHENTHEGRASS

is dry. Avoid edging in wet soil or grass as the blade

guard might clog or result in an uneven edge. If the

blade guard becomes clogged, stop the engine &

remove debris from the blade guard.

Always remove the spark plug lead when cleaning the blade or guard!

Paths and Kerbs

s3ETTHECUTTINGHEIGHTSOTHATTHEBLADETIPCUTS

APPROXIMATELYMMBELOWTHESURFACE4HEBLADE

alignment indicator is located on the blade guard.

Align the indicator with the edge of the path or the

curb which is to be cut.

s!LWAYSCUTINAFORWARDDIRECTION

s!VOIDALLOWINGTHEBLADETOCONTINUALLYCONTACTANY

concrete or other hard edge.

Walls and Fences

s4OENABLEYOUREDGERTOCUTRIGHTUPTOAWALLOR

a fence the right rear wheel must be placed on

the lowest setting. Place the left hand side of the

machine against the vertical surface and cut a

narrow grove between the wall and the lawn.

Note: This operation will produce best results

when the blade is new! If the blade is heavily

worn it will not cut a satisfactory edge!

Note: Always take care to avoid damage to

brick work, paths, pavers and tiles!

Cutting Tips

Operating the Edger

Blade

Guide

Not for

Reproduction

11

Starting the Edger

NOTE: Before starting your edger read the engine chapter then set the edger

operating height!

#ONNECTSPARKPLUGLEAD%NSURETHE

lead cover fits firmly onto the spark

PLUG

2. Fill tank with fuel 2.0 litres of

unleaded fuel.

4URN/./&&SWITCHTOTHE"ON" 4. Turn fuel tap to the "ON" position.

5. Set throttle to the "Choke" position. 0ULLTHEENGINESTARTERUNTILITENGAGES

Then pull starter cord briskley until the

engine starts.

Fuel

Tank

Spark

Plug

/./&&

Switch

Zone

Clip

Assemble starter cord & knob through the "Zone Clip" eyelet as shown. This will assist

with starting the engine & will prevent cord backlash damaging the Edger. Avoid pulling

the starter cord beyond the cord length limit. Always gently return the cord knob recoil -

Never release knob to backlash.

OPERATING INSTRUCTIONS

Fuel Tap

Choke

Position

Not for

Reproduction

12

NOTE: If problems arise consult an authorised Victa Service Centre.

s 4OENGAGETHECUTTINGFEATURE4ILTTHEEDGER

backwards slightly and pull engagement bail

against Edger handle.

NOTE: During engagement the blade will plunge

towards the ground! Take care to ensure

the blade is in position!

s 4OAVOIDMISCUTTINGTILTTHEUNITBACKWARDSTO

engage the blade before lowering the blade into

THEGROUND

s (OLDTHEREWHILECUTTINGISREQUIRED

s 4ODISENGAGETHECUTTINGFEATURERELEASETHEBAIL

lever.

Pull to Drive

Release

to stop

Engagement Bail

7. Move Throttle to the "RUN" position. 4OSTOPTHEENGINERELEASETHEBAIL

and wait for the blade to stop then

turn "ON-OFF" switch to the "OFF"

position.

IMPORTANT: Turn fuel tap "OFF" after use!

Always store in a level position with both wheels set to "0" height

Never leave the edger running idle!

Cutting Control Operation

OPERATING INSTRUCTIONS

Starting the Edger

Bail Engagement

NOTE: "CHOKE" must be used at all times when starting the engine!

(When engine is HOT or COLD)

Not for

Reproduction

Cleaning

13

sRemove grass build up from the air intakes on the starter cowl, around the engine,

carburettor, and the air filter housing.

s!NYBUILDUPOFGRASSORTWINEONSPINDLESHOULDBECLEANEDANDREMOVED

s 4HEUNDERSIDEOFTHE%DGERSHOULDBECLEANEDREGULARLYTOREMOVEDIRTANDGRASSASANY

build up will promote corrosion on the steel baseplate.

s When cleaning the underside of the Edger, tilt the handle back so the front wheel is off

the ground. Tilting in any other direction can cause the oil to contaminate & damage the

air filter causing starting difficulties.

NOTE: Do not leave edger tilted backwards for periods longer than 5 minutes!

s!LWAYSKEEPTHE%DGERINTHEUPRIGHTPOSITION$ONOTLAY%DGERONITSSIDE

s A hose can be used to clean the underside of your Edger. Care must be taken to "NOT"

get water into the engine as it may damage the magneto or get into the fuel system.

s 4OPREVENTCHASSISCORROSIONTHEUNDERSIDEOFYOUR%DGERSHOULDBECLEANED

immediately after edging an area which has been recently dressed with sulphate of

ammonia or fertiliser.

s !FTERCLEANINGRUNTHEENGINEBRIEFLYTODRYOFFEXCESSMOISTUREBEFORESTORING

Before cleaning the Edger ensure the "ON -OFF" switch is in the "OFF"

position. Turn the fuel tap off and disconnect the spark plug lead.

DO NOT CLEAN THE EDGER WHEN THE ENGINE IS RUNNING!

For Your Safety

s.EVERUSETHE%DGERUNLESSTHEGUARDSSUPPLIEDBYTHEMANUFACTURERAREINPOSITION

s"EFORESTARTINGTHEEDGERCHECKBLADESANDBOLTSFORDAMAGEORWEAR

s)FYOUSTRIKEANOBSTRUCTIONSTOPTHEENGINEANDCHECKTHEBLADEFORDAMAGE

s3TOPTHEENGINEANDDISCONNECTTHESPARKPLUGLEADBEFOREADJUSTINGBELTTENSIONORFITTING

new blades.

• "DO NOT" lay the Edger on its side!

Use only genuine replacement parts made and guaranteed by Victa, insist on them

from your parts and service dealer.

NOTE: Use of non-genuine blade may void your warranty and could result in damage

or injury

Safety notes

MAINTENANCE

&

CARE

Not for

Reproduction

Adjusting belt tension

2EMOVETHECABLECOVERSILVER

X0HILLIPSHEADSCREWS

2. Loosen tension arm bolt

4. Engage the bail and check that

THESPRINGSTRETCHESBYMM

3. Rotate tension arm slightly and

RETIGHTENSCREW

)FSPRINGSTRETCHISNOTMM

2EPEATSTEPUNTILSPRINGISCORRECT 2EPLACETHECABLECOVERSILVER

XPHILLIPSHEADSCREWS

NOTE: Always Check blade brake operation after adjustment!

If correct belt adjustment cannot be achieved your belt may need replacing!

Replace belt if worn or damaged! 14

3. 4.

5. 

2.

Belt tensioning may need increasing when the following symptoms arise

s0OORCUTTINGs"LADEFREQUENTLYSTALLINGROUNDORAPPEARTOSTOP

s"ELTWORNs"LADEWILLNOTROTATEORROTATESINTERMINTALLY

1.

MAINTENANCE

&

CARE

Not for

Reproduction

15

4. Install the new blade, washer

#ONCAVETOFACEBLADEREFIT.UT

3. Remove the split pin, blade nut,

washer & used blade.

,OOSENTHENUTTURNANDALIGN

the slot with the spindle hole.

5. Tighten the nut until the conical washer

ISFLATAGAINSTTHEBLADE.M

Blade Replacement

2. Place pin or phillips head screw

driver into the locking hole.

1. Rotate the blade until the locking hole

in the lower pulley & bearing housing

line up.

"ENDTHESPLITPINLEGSOUTWARDS

to rest against the nut.

7. Insert split pin through the slot and

spindle hole until the pin head is against

the nut.

1.

5.

7.

3.





4.

Push pin

inside slot!

2.

MAINTENANCE

&

CARE

Not for

Reproduction

16

Engine - Components

Spark Plug

Air Filter Housing

Mufﬂer

Fuel Tank

Fuel Cap

ON/OFF Switch

Starter grip

Throttle Control

"Choke - Run"

Fuel Tap

Starter

Oil Filler Cap /

Dip Stick

MAINTENANCE

&

CARE

Not for

Reproduction

Engine - Oil Level

Engine - Fuel

Briggs & Stratton 550 Engine must have 600ml S.A.E. 30 Oil placed in the Sump Before

Starting engine Do not over fill the sump!

PRE OPERATION CHECK

1. Clean dirt from around the oil filler cap area.

2. Remove oil filler cap and wipe clean.

$IP/ILFILLERCAPDIPSTICKINTOENGINE

(Do not screw in to check)

2EMOVEOILFILLERCAPDIPSTICKANDCHECKOILLEVEL

5. If the oil level is low add the recommended oil to the

upper mark on the dipstick.

(600ml S.A.E. 30 Oil - Sump Max Capacity)

6. Always check oil level 3 times.

Note: When the edger is level the oil capacity will

roughly fill/reach the brim of the sump oil filler.

CAUTION! Running the engine with insufficient oil can cause serious

engine damage. Be sure to check engine on a level surface with engine

stopped.

CAUTION! DO NOT USE nondetergent oil or 2 stroke engine oil as it will

shorten the engine service life and will not be covered under warranty.

s BRIGGS & STRATTON 550 ENGINE MUST USE REGULAR UNLEADED PETROL.

s FUEL TANK CAPACITY IS 2.0 LITRES

s.EVERUSE/ILPETROLMIXTUREORDIRTYFUEL!VOIDGETTINGDIRTDUSTORWATERINTHE

fuel tank.

s0ETROLISEXTREMELYFLAMMABLEANDISEXPLOSIVEUNDERCERTAINCONDITIONS

s2EFUELINAWELLVENTILATEDAREAWITHTHEENGINESTOPPED$ONOTSMOKEALLOWFLAMESOR

any ignition source in the area where the engine is refilled or where petrol is stored.

s$ONOTOVERFILLTHEFUELTANK (There should be no fuel in the filler neck) after

refuelling. Make sure the fuel tank cap is closed and ensure fuel cap is properly secured.

s"ECAREFULNOTTOSPILLFUELWHENREFUELLING3PILLEDFUELORFUELVAPORMAYIGNITE)FANYFUEL

is spilt make sure the area is dry before starting the engine.

s!VOIDREPEATEDORPROLONGEDCONTACTWITHSKINORBREATHINGOFPETROLVAPOR

s/NLYSTOREFUELINANAPPROVEDCONTAINER(Victa Fuel Can)

CAUTION! - KEEP FUEL AND OIL OUT OF REACH OF CHILDREN

MAX

MIN

Oil Dip Stick

Maximum Oil Level

Minimum Oil Level

5.

17

CAUTION! Always ensure the edger is level and on flat ground when

checking or filling oil! Adjust roller and wheel heights as required.

MAINTENANCE

&

CARE

Not for

Reproduction

Page is loading ...

Simplicity EDGER GE254 User manual

Simplicity EDGER GE254 User manual

Related papers

Other documents