Dexter Laundry T-950 Express Installation guide

Brand: Dexter Laundry

Model: T-950 Express

Category: Washing machines

Type: Installation guide

Dexter Laundry T-950 Express is a 60-pound capacity, computer-controlled coin washer designed for commercial use. It features a variety of wash cycles, including pre-wash, wash, rinse, final rinse, and spin. The washer also has a built-in detergent and fabric softener dispenser, as well as a bleach dispenser. The T-950 Express is easy to operate, with a simple control panel that includes a digital display and push-button controls. It also has a safety door lock that prevents the door from being opened during the wash cycle.

P/N 8514-183-001B

MODEL T900/950

60LB CAPACITY

COMPUTER CONTROL

COIN WASHER

DEXTER

LAUNDRY,

INC. OWNER'S BOOKLET

INSTALLATION & OPERATION

INSTRUCTIONS

Please read this information and retain for reference.

WARNING - THIS WASHER IS EQUIPPED WITH DEVICES AND FEATURES RELATING TO ITS SAFE

OPERATION. TO AVOID INJURY OR ELECTRICAL SHOCK, DO NOT PERFORM ANY SERVICING

UNLESS QUALIFIED TO DO SO.

IT IS THE RESPONSIBILITY OF THE OWNER TO CHECK THIS EQUIPMENT ON A FREQUENT

BASIS TO ASSURE ITS SAFE OPERATION.

A machine should not be allowed to operate if any of the following occur:

- Excessively high water level.

- If machine is not connected to a properly grounded circuit.

- If the door does not remain securely locked during the entire cycle.

- Vibration or shaking from an inadequate mounting or foundation.

WARNING - FOR SAFETY

1. Always shut off power and water supply before servicing.

2. Do not overload the washer.

3. Do not open door when cylinder is in motion or it contains water.

4. Do not bypass any safety devices of this washer.

5. Do not use volatile or flammable substances in or near this washer.

6. Keep all panels in place. They protect against shock and injury and add rigidity to the washer.

PREVENTIVE MAINTENANCE REQUIREMENTS

DAILY

- Check that the loading door remains securely locked and cannot be opened during the entire cycle.

- Check the water connections for leaks.

- Clean the top and sides of the cabinet to remove residue.

- Clean the soap dispenser and lid and check that the lid is in-place and tight.

- Check the drain valve for leaking and that it opens properly.

- Check the loading door for leaks. Clean the door seal of all foreign matter.

- Leave the loading door open to aerate the washer when not in use.

QUARTERLY

- Make sure the washer is inoperative by switching off the main power supply.

- Check the V-belts for wear and proper tension.

- Clean lint and other foreign matter from around motor.

- Check all water connections for leaks.

- Wipe and clean the inside of the washer and check that all electrical components are free of moisture and dust.

- Remove and clean water inlet hose filters. Replace if necessary.

- Check anchor bolts - retighten if necessary

IMPORTANT: Replace any and all panels that were removed to perform daily and/or quarterly maintenance.

Fabric So ftener

Add

Bleach

Detergent





FINAL

RINSE SPINWASHON RINSE



 

1 Load laundry, close and latch door.

3 Select wash temperature.

4 Insert coins/card.

into d ispen ser on front of machine.

2 Add detergent and fabric softener

5 Press S TART button.

(Optional)

6 Add bleach when light comes on.

remains locked until cycle is completed.

Door Locks when machine starts, and

Quarters Only



for 3 seconds.

Push and Hol d

MODEL T900/950

DEXTER

LAUNDRY,

INC.

INSTALLATION INSTRUCTIONS

All washers must be installed in accordance with all local, state and national building,

electrical, plumbing and other codes in effect in the area.

WARNING - THESE INSTALLATION AND SERVICING INSTRUCTIONS

ARE FOR USE BY QUALIFIED PERSONNEL ONLY. TO AVOID INJURY

AND ELECTRICAL SHOCK DO NOT PERFORM ANY SERVICING

OTHER THAN THAT CONTAINED IN THE OPERATING

INSTRUCTIONS, UNLESS QUALIFIED.

FOUNDATION REQUIREMENTS

This machine is designed for use on or over bare concrete floor - not to be used above combustible

flooring. The washer must be securely bolted and grouted to a substantial concrete floor, or

mounted and grouted upon a suitable base that is securely bolted and grouted to a substantial

concrete floor. CARE MUST BE STRESSED WITH ALL FOUNDATION WORK TO INSURE A

STABLE UNIT INSTALLATION, ELIMINATING POSSIBILITIES OF EXCESSIVE

VIBRATION. All installations must be made on sound concrete floors, 8 inches (203 mm) or

thicker. Anchor bolts or expansion anchors must be of a quality grade and a minimum of 3/4-inch

(19 mm) diameter. Six bolts are required to mount the washer to the steel base or concrete pad.

MOUNTING

A concrete pedestal or steel-mounting base that elevates the machine approximately 4 inches (102

mm) above the floor level is recommended to provide easy access to the loading door. Allow a

minimum of 24 inches (610mm) of clearance behind the rear of the machine, to provide access for

motor removal. Refer to Fig. 1-1 and 1-2 for machine bolt-down dimensions.

If an elevated concrete pedestal is desired, it should be embedded into the existing floor. Anchor

bolts should be 3/4" x 8" (19 mm x 200 mm), grade 8 or better, headed by a 4 inch (10 cm) square

fish plate and should protrude 2 1/2” (64 mm) above the finished surface of the pedestal.

EXPANSION ANCHORS ARE NOT RECOMMENDED FOR USE IN CONCRETE PEDESTALS,

BECAUSE THE ANCHORS ARE TOO CLOSE TO AN EDGE, CAUSING IT TO BREAK OUT.

(See Fig. 1-1 and 1-3.)

CONCRETE PEDESTAL MOUNTING

Figure 1-1 Figure 1-2

FLOOR OUTLINE

Figure 1-3

MACHINE MOUNTING DETAIL

PLUMBING

Water supply hoses are furnished with each machine. The threaded connections on the hoses are ¾-11

½ NHT.

Separate hot and cold water lines must be provided, maintaining 30 psi to 120 psi (207 kPa to 827

kPa) water flow pressure. A 140F (60C) degree hot water supply is recommended for best washing

results.

DRAIN

The drain outlet tube at the rear of the machine is 3 inches (76 mm) in diameter. Any drain hose used

must be lower than the drain valve to assure proper draining.

ELECTRICAL

WARNING

SHUT OFF POWER AND WATER BEFORE OPENING ANY SERVICE PANELS.

Dexter single/three-phase 208-240VAC 60 Hz washing machines are intended to be permanently

installed appliances. No power cord is provided. The machine should be connected to an individual

branch circuit not shared by lighting or other equipment. The connection should be sheathed in liquid

tight flexible conduit, or equivalent, with conductors of the proper size and insulation. A qualified

technician should make such connections in accordance with the wiring diagram. (Suggest a minimum

wire size of 12 ga.)

TO MAKE ELECTRICAL CONNECTIONS: Disconnect all power to the washer. Remove screw and

lift out the cover located in the upper left corner of the machine (as viewed from the back).

 If power is 208-240-3PH-60Hz, connect L1, L2, L3 and ground. If there is a high leg it must be

connected to L3.

 If power is 208-240-1PH-60Hz, connect L1, L2 and Ground.

NOTE: It is important that the grounding screw next to the power terminal block TB-1 be connected

to a good external ground.

FUSING REQUIREMENTS:

SINGLE- and THREE -PHASE MODELS - 20 AMP TIME-DELAY (DUAL ELEMENT)

FUSE (or equivalent circuit breaker). *

*Note: For elevations above 6600 feet or very hot climates, a 30 amp breaker is recommended due

to down-rating of circuit breakers under these conditions.

CONTROLS TRANSFORMER:

The controls transformer is located inside the control trough and steps a range of 208 to 240 volts down

to 115 volts. There are two terminals on the controls transformer for the primary (incoming) power.

Use the terminal marked “208V” for power supplies between 208 and 215 volts. Use the terminal

marked “230V” for power supplies between 216 and 240 volts.

CHECKOUT

After all mounting, plumbing and electrical work is completed, the washer should be run through a

cycle and checked for water leaks and proper functioning.

STARTING THE WASHER

A. Load the clothes into the cylinder and latch the door securely. Be sure clothing does not

get caught between the door gasket and tub front when closing the door. Maximum load is

60 pounds clothes, dry weight. Do not load the washer with more than 60 lbs.

B. Select the appropriate cycle temperatures for the load being washed.

C. Add low sudsing powdered detergent into the “detergent” compartment of the automatic

dispenser on the front of the washer. If desired add fabric softener to the “fabric softener”

compartment. Use the amount of fabric softener as recommended by the manufacturer.

If liquid wash products are used in the “detergent” compartment, they must be added at

the beginning of the wash cycle.

If the machine is set for pre-wash, washing products can be added to dispenser or put in with

the clothes when loading the washing machine.

D. Insert coins, tokens or debit card to meet the displayed vend price. Once the vend price is

met, the display will read “PUSH” and the start button LED will blink. If the door is not

closed and latched, the display will read “DOOR” and the control will wait until the door

is latched to continue. Pressing the start button will begin the cycle and activate the ON

light. The display will go blank for a moment and then display the cycle time in minutes.

The clothes door will lock and remain locked until the end of the cycle.

END OF CYCLE

When the cycle is complete the time will display “0” until the door is opened and a 5-second tone

will sound. The door can now be opened. Leave the clothes door open when the machine is not in

use.

EMERGENCY STOP / SAFETY DOOR LOCK

This machine is equipped with a Safety Door Lock that locks the door closed from when the cycle is

started until the cycle is complete. The door lock prevents opening the door for up to 3 minutes if the

power is interrupted during the cycle.

The Emergency Stop button pauses the washer and allows the door to be opened during the cycle

after the Safety Door Lock releases. When the Emergency Stop button is pressed an alarm will

sound and the display will begin counting down from “3”. If the button is released before 3 seconds

elapse, the alarm will stop and the cycle will continue normally. If the Emergency Stop is held

down for 3 seconds, the display will count down to “0” and the washer will begin stopping

movement and water flow and begin draining water from inside the washer. Though the machine

may stop wash movement quickly, it may take up to 3 minutes for the door to unlock. During that

time the alarm will continue to sound. When the alarm stops, the door may be opened. The washer

may be restarted by closing and latching the door, and pressing the Start button. If the washer was

stopped more than once before the final extract, the cycle will be cancelled. If the washer was

stopped during final extract, the cycle will be ended. If the washer is stopped for more than 1 hour,

the cycle will be terminated. SPECIFICATIONS

MODEL T900/950 60LB WASHER

CAPACITY

CYLINDER SIZE

ELECTRICAL

DRIVE SYSTEM

WASH SPEED

INTERMEDIATE

EXTRACT

FINAL EXTRACT

MACHINE CONTROL

WATER INLET

DRAIN VALVE

60LBS/9 CUBIC FT. (27.2 kg/255 L)

30” DIA X 22” DEEP (76.2cm X 55.9cm)

208-240 VAC, 60 HZ, 1 OR 3 PHASE

SOFT START REVERSING INVERTER DRIVE

43 RPM

375 RPM (60 G’S)

484 RPM (100 G’S) / 573 RPM (140 G’S) / 685 (200 G’S)

PROGRAMMABLE COMPUTER WITH 6 STANDARD CYCLES.

4 SOLENOID OPERATED VALVES

FLOW RATE: 2 DUAL VALVES (9 GAL/MIN) EACH, 30-120

PSI,

2 SINGLE VALVES (12 GAL/MIN) EACH, 30-120 PSI

3” DIAMETER

PROGRAMMING INSTRUCTIONS:

Programming can be accomplished manually using the machine controls or by connecting to the

machine control using a PDA (personal digital assistant). For instructions on using a PDA with this

washer control, please contact your local Dexter distributor. Please read below for manual

programming instructions.

The washer has two levels of programming. The Coin/Price Programming allows the owner to set

the price for the washer features and the values of the coins. The Washer Cycle Programming allows

the owner complete access to the wash cycle parameters – add/remove a bath, bath times, spin times,

water temperatures, etc. To enter the programming modes, the top of the washer must be unlocked

and slid toward the back of the washer a few inches.

COIN PRICE PROGRAMMING

While the washer is in the Idle mode, push the Programming pushbutton on the controller. The Idle

mode is when the washer is not running a cycle and the price of the bath is displayed. The

Programming pushbutton is a very small button located on the upper center of the controller directly

behind the display. There are seven stages in the Coin/Price Programming mode.

Stage 1: Right Coin – The display will blink first a “r” indicating right coin and then a coin value

($1.00 – default). The display will blink back and forth between the “r” and the value. To change

the value, use the Hot temperature button to decrease and the Warm temperature button to increase.

The value will change in 1¢ steps. The range of values is from $00.00 to $99.99. When the desired

right coin value is displayed, push the Start button once to store the new value and a second time to

move to the next Coin/Price programming step.

To exit the Coin/Price programming mode, push the Cold temperature button for 5 seconds.

Stage 2: Left Coin – The display will blink first a “L” indicating left coin and then a coin value

($0.25– default). The display will blink back and forth between the “L” and the value. To change

the value, use the Hot temperature button to decrease and the Warm temperature button to increase.

The value will change in 1¢ steps. The range of values is from $00.00 to $99.99. When the desired

left coin value is displayed, push the Start temperature button once to store the new value and a

second time to move to the next Coin/Price programming step. To exit the Coin/Price programming

mode, push the Cold temperature button for 5 seconds.

Stage 3: Wash Price – The display will blink first a “P” indicating wash price and then present wash

price. The display will blink back and forth between the “P” and the price. To change the value, use

the Hot temperature button to decrease and the Warm temperature button to increase. The value will

change in 1¢ steps. The range of values is from $00.00 to $99.99. If the wash price is set to $00.00,

the display will show “FREE” after exiting the programming mode. When the desired price is

displayed, push the Start button once to store the new value and a second time to move to the next

Coin/Price programming step. To exit the Coin/Price programming mode, push the Cold temperature

button for 5 seconds.

To step through to the desired stage, repeatedly push the START button until the desired

stage is blinking on the display. To exit the Coin/Price programming mode, push and hold

the Cold temperature button for 5 seconds.

WATER TEMPERATURE PRICING

The washer can be set for different levels of pricing for Cold, Warm and Hot water. The Cold water

setting is considered as the base price, which is the normal washer cycle price.

Stage 4: Warm Water Price – The next step in the pricing program is to set the additional price for

Warm water usage. The additional price is the amount added to the price of a cold wash. The

display will blink first “CH P” indicating cold/hot water mix price and then “00.00”. To change the

value, use the Hot temperature button to decrease and the Warm temperature button to increase. The

value will change in 1¢ steps. The range of values is from $00.00 to $99.99.

When the desired price is displayed, push the Start button once to store the new value and a second

time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,

push the Cold temperature button for 5 seconds.

Stage 5: Hot Water Price – The next step in the pricing program is to set the additional price for Hot

water usage. The additional price is the amount added to the price of a cold wash. The display will

blink first “H P” indicating hot water price and then “00.00”. To change the value, use the Hot

temperature button to decrease and the Warm temperature button to increase. The value will change

in 1¢ steps. The range of values is from $00.00 to $99.99.

When the desired price is displayed, push the Start button once to store the new value and a second

time to move to the next Coin/Price programming step. To exit the Coin/Price programming mode,

push the Cold temperature button for 5 seconds. The Coin/Price programming mode will

automatically exit and return to the Idle mode if no buttons are pushed for one minute.

Stage 6: Plus Cycle Price -- The next step in the programming sequence is the Plus Cycle feature.

The Plus Cycle adds three (3) minutes of wash time to the wash bath only. The controller can be

programmed to charge a fee for this or the feature can be turned off. The default setting is off. To

turn the Plus Cycle feature off, set the Plus Cycle price to zero.

The display will blink first a “PC P” indicating Plus Cycle price and then price (back and forth). To

change the value, use the Hot temperature button to decrease and the Warm temperature button to

increase. The value will change in 1¢ steps. The range of values is from $00.00 to $99.99. When

the desired price is displayed, push the Start temperature button once to store the new value and a

second time to move to the next Coin/Price programming step. To exit the Coin/Price programming

mode, push the Cold temperature button for 5 seconds.

Stage 7: Decimal Point -- The next step in the programming sequence is the decimal point display.

The display will start blinking back and forth first “dP “ (Decimal Point) and then either “on”

(default) or “off”. Press the Hot or Warm temperature buttons to select the decimal point display as

“on” or “off”. When the desired setting is displayed, push the Start button to store it and a second

time to move to the next programming step.

Note: To not use this feature, set the price to “00.00”.

WASH CYCLE PROGRAMMING

To change a feature of the wash cycle, push and hold the Hot temperature button and then push the

programming pushbutton on the controller. The Washer must be in the Idle mode to enter the Wash

Cycle Programming mode. When entering the cycle programming mode, the Bleach LED will start

to blink and continue to blink as long as you are in the Cycle Programming mode.

The display will show “C 0”. This is the default cycle number.

End of Cycle Alarm: The end of cycle alarm can be turned on or off by pushing the Hot or Warm

temperature buttons until “AL” is displayed and pressing the Start button. The display will now read

“on” or “off” and can be changed by pressing the Hot or Warm temperature buttons. When the

desired setting is displayed, press Start again to save.

Modifying the Wash Cycle: To change the wash cycle, push the Hot or Warm temperature buttons

until the display changes to “C 1”, indicating cycle one is selected. The temperature buttons are

used to make changes to the program. In the program mode, the buttons will do the following:

When the display shows “C 1”, push Enter. The display will show “b“ and the PreWash mode light

will blink. Use the Up/Down buttons to move to the bath that will be changed. As Up/Down

buttons are pushed, the next bath mode light turns on.

When the Up button is pushed, the bath mode light changes from Prewash to Wash. With each

Note: The washer can be returned to the factory default settings by holding

the Start button and then pressing the Warm button. The display must

show “C 0” to do this. When the cycle default values are loaded, the

washer will automatically exit the programming mode.

Note: The Wash Cycle programming mode will automatically exit and return to

the Idle mode if no buttons are pushed for one minute.

additional push of the Up button, the lit bath mode changes from left to right: Prewash, Wash, Rinse

and Final Rinse. As there are two possible Rinse bathes, for Rinse1 the Rinse LED and the display

changes to “b” in the left digit and “r1" in the two right hand digits. For Rinse2, the display changes

to “b” in the left digit and “r2" in the two right hand digits. Note that the Spin light is not used.

When the Down button is pushed, the bath mode light changes from Prewash to Final Rinse, etc.

There is a wrap around feature in both directions. When the desired bath mode light is on, push

Enter.

The selected bath LED begins to blink. The display shows the letters “ct” in the left two digits and

the bath cycle time in the right two digits. Again the up/down buttons change this value. The range

is shown below. If zero time is entered, then the bath will be skipped and the program will return to

the bath selection. When the desired cycle time is selected, push enter.

The display shows the letter “t” in the left digit and the letters “CC” appear in the right two digits.

This is the bath water temperature. The selection choices are shown below but for the coin washer

the value is defaulted to CC. When the desired temperature is selected, press enter.

The display shows the letter “L” in the left digit and the letters “LO” appear in the right two digits.

This is the bath water level. The selection choices are shown below but for the coin washer the

value is defaulted to LO. As it is not selectable with a coin washer, the owner pushes enter to

continue.

The display shows the letters “dF” in the left two digits and the letter “t” appears in the right digit.

This is the bath delay fill. The selections are “t” for counting down bath time during the fill or “d”

for delay the bath time until water level is reached. When the desired selection is made, push enter.

The display shows the letter “S” in the left digit and the bath spin time in the right two digits. Again

the up/down buttons change this value. The range is shown below. When the desired spin time is

selected, push enter.

The display shows the letters “IS” in the left two digits and the injection selection appear in the right

digit. For the coin washer the default value is “0" and cannot be changed. Push enter twice.

At this point the bath LED stops blinking. The display will show “b” and the next bath LED lights.

Again use the up/down buttons to change the bath selection. To exit the programming mode, push

and hold exit for 5 seconds. The cycle will be stored when exiting the programming mode.

COIN WASHER CYCLE PARAMETER RANGES

The range of each cycle parameter is shown below:

Cycle Time “ct” 0 to 15 minutes for Prewash, Rinse1 and Rinse2

3 to 15 minutes for Wash and Final Rinse

For the bathes that can, if the time is set to zero, then the bath

will be eliminated from the cycle.

Water Temperature “t” HH – hot, CH – warm, CC – cold

The owner can set the bath default. For the wash bath, the

customer overrides the default for that cycle when the

temperature is selected.

Water Level “L” LO – low

The owner can change the displayed value, but for a coin

washer only LO will be put into the cycle.

Delay Fill “dF” The selections are “d” for delay the bath time until water level

is reached or “t” to countdown bath time during the fill.

Spin Time “S” 0 to 10 minutes for Prewash, Wash, Rinse1 and Rinse2

1 to 10 minutes for Final Spin.

“IS” The owner can change the displayed value, but for a coin

washer only 0 will be put into the cycle.

COIN WASHER DEFAULT CYCLE

The following table shows the complete details for the coin washer default cycle.

Bath

Bath Cycle

Time

(min.)

Water

Temp.

Water

Level *

Delay Fill Spin Time

(min.)

IS *

Prewash

CC LO t 0

Wash

CH LO t 0

Rinse 1

CC LO t 1

Rinse 2

CC LO t 0

Final

Rinse

CC LO t 4

Note * These default values are preset and cannot be changed.

RAPID ADVANCE MODE

To enter the Rapid Advance mode, push and hold the Cold water temperature button and then push

the programming button on the controller. There will be no observed change to the washer or the

display. The Rapid Advance mode can be entered from either the Idle mode or during the cycle. To

rapid advance to the next step in the wash cycle, push the Start and Warm temperature buttons at the

same time. The display will show an “Ad” (advance) in the display. The washer will advance to the

next bath segment. The water will drain before the advance will occur.

The Rapid Advance mode will not end until the final bath segment is completed. The final segment

cannot be skipped in Rapid Advance mode.

Notes: 1. When the Rapid Advance mode is used, the cycle time will no longer be correct.

2. By skipping steps with rapid advance, the door may not open immediately at the end of

the cycle.

EASY CARD

If your Dexter washer is installed with Dexter’s Easy Card debit card system, the card reader signals

the washer control when money is debited from the user’s card account to satisfy the price of the

wash cycle. The washer’s pricing and the Easy Card system pricing are completely independent of

each other and must be programmed separately and coordinated. Refer to the instructions that came

with the Easy Card system for complete information.

SETTING THE ELECTRONIC COIN ACCEPTOR SWITCHES

Some washer models come equipped with an electronic coin acceptor. Follow the instructions

below for setting the switches for the desired country and currencies.

1) The electronic coin acceptor has switch settings depending on the coins and country. See the

table below for available values of the left and right coin inputs for the available countries.

WARNING: TURN POWER OFF BEFORE AND LEAVE POWER OFF WHEN

CHANGING THE SWITCHES OF THE ELECTRONIC COIN ACCEPTOR.

2) Turn power back on and test coins to ensure proper operation.

Acceptor P/N Country Left Coin Right

Coin SWs 1-8 SWs 9-16

9021-010-001

Canada 25¢ ↓↓↑↑↑↑↑↓ ↓↑↑↑↑↑↑↓

Canada $1 ↑↑↓↓↓↑↑↓ ↓↑↑↑↑↑↑↓

Canada $2 ↑↑↑↑↑↓↓↓ ↓↑↑↑↑↑↑↓

Japan 100¥ ↓↓↑↑↑↑↑↓ ↑↓↑↑↑↑↑↓

Japan 500¥ ↑↑↓↓↑↓↓↓ ↑↓↑↑↑↑↑↓

Taiwan 10NT ↓↓↑↑↑↑↑↓ ↑↑↓↑↑↑↑↓

Taiwan 50NT ↑↑↓↓↑↓↓↓ ↑↑↓↑↑↑↑↓

Korea 500W ↓↓↑↑↑↑↑↓ ↑↑↑↓↑↑↑↓

Greenwald 118-1 Token ↑↑↑↑↑↑↑↓ ↑↑↑↑↓↑↑↓

Greenwald 118-5 Token ↑↑↑↑↑↑↑↓ ↑↑↑↑↑↓↑↓

U.S.A. 25¢ ↓↓↑↑↑↑↑↓ ↑↑↑↑↑↑↓↓

U.S.A. $1 ↑↑↓↓↑↑↑↓ ↑↑↑↑↑↑↓↓

9021-011-001

Australia 10¢ ↓↓↑↑↑↑↑↓ ↑↓↑↑↑↑↑↓

Australia 20¢ ↑↑↓↓↑↑↑↓ ↑↓↑↑↑↑↑↓

Australia $1 ↑↑↑↑↓↓↑↓ ↑↑↓↑↑↑↑↓

Australia $2 ↑↑↑↑↑↑↓↓ ↓↑↓↑↑↑↑↓

New Zealand 10¢ ↓↓↑↑↑↑↑↓ ↑↓↑↑↑↑↑↓

New Zealand 20¢ ↑↑↓↓↑↑↑↓ ↑↓↑↑↑↑↑↓

New Zealand $1 ↑↑↑↑↓↓↑↓ ↑↑↑↓↑↑↑↓

New Zealand $2 ↑↑↑↑↑↑↓↓ ↓↑↑↓↑↑↑↓

Hong Kong $5 ↓↓↓↓↑↑↑↓ ↑↑↑↑↓↑↑↓

Hong Kong $10 ↑↑↑↑↓↓↑↓ ↑↑↑↑↓↑↑↓

Greenwald 118-1 Token ↑↑↑↑↑↑↑↓ ↑↑↑↑↑↓↑↓

Greenwald 118-5 Token ↑↑↑↑↑↑↑↓ ↑↑↑↑↑↑↓↓

Switches ↑=up/on, ↓=down/off

Note: Coins and tokens in the left coin column will result in one pulse to the left coin input.

Note: The $1, 500¥, 50NT, and $10 coins in the right coin column will result in one pulse to the

right coin input, while the $2 coins will result in two pulses to the right coin input.

Note: Acceptance of multiple coins per country and multiple tokens is allowed. Only the down/off

setting for each coin and token is required to accept that coin or token.

WASHER ERROR CODES

Fault#

(F #) Description Customer Action

1 The door failed to close and lock or the door

failed to remain locked after three tries of

latching the door and starting during the cycle.

Turn off the power to the washer. Check wire connections to door /lock switches. Check wire

connections from switches to controller. If necessary door lock mechanism should be

adjusted by a qualified person. Turn on the power to the washer. (See Note)

The washer tub does not fill with water within

7 minutes. The wash cycle will continue. The

F 2 will flash three times, then wait for 30

seconds. The error will clear at the end of the

cycle.

Turn of the power to the washer. Check the operation of the water valves. Check the

incoming water pressure. Check for blocked or restricted water flow. Check to ensure the

drain valve is functioning properly. Turn on the power to the washer. (See Note)

3 Memory error in controller. Turn off the power to the washer. Wait one minute. Turn power back on to the washer. If the

problem returns, clear the fault with the Palm. If the problem returns again, replace the

washer controller.

4 Washer controller communication error Turn off the power to the washer. Wait one minute. Turn power back on to the washer. If the

problem returns, replace the washer controller.

Pressure Switch error ( only OPL )- when the

high level sensor indicates full but the lower

one indicates empty. The wash cycle will

continue. The F 5 will flash three times, then

wait for 30 seconds. The error will clear at the

end of the cycle.

Turn off the power to the washer. Replace the pressure switch. Turn on power to the washer.

(See Note)

Wrong washer size for drive type. Turn off the power to the washer. Check to ensure all the harnesses are properly connected

to the controller. Check to ensure the drive horsepower is proper for this size of washer. Turn

on power to the washer. (See Note) If problem reappears, contact your Dexter

representative.

7 Wrong size drive installed Turn off the power to the washer. Check to ensure all the harnesses are properly connected to

the controller. Check to ensure the drive horsepower is proper for this size of washer.

Contact your Dexter representative.

The washer tub does not empty within 7

minutes. The wash cycle will continue. The F

8 will flash three times, then wait for 30

seconds. The error will clear at the end of the

cycle.

Turn off the power to the washer. Check to ensure the drain valve is operating properly.

Check to ensure the pressure switch tube is clear of blockage. Check to ensure the pressure

switch is operating proper. Correct any located problems. Turn on power to the washer. (See

Note)

The washer tub does not reach the spin target

frequency within 200 seconds. The wash

cycle will continue. The F 9 will flash three

times, then wait for 30 seconds. The error will

clear at the end of the cycle.

Turn off the power to the washer. Inspect the washer to ensure the tub spins freely. If

restricted, then clear the blockage. Test washer. If tub spins freely, the drive needs to be

replaced.

10 After a spin the washer tub does not stop

within 150 seconds. Turn off the power to the washer. Inspect the braking resistors and the connecting wiring to

the drive braking resistors mounted in the top of the washer. If the resistors and wiring is

correct, then replace the drive.

The drive size setting has changed. Turn off the power to the washer. Check to ensure all the harnesses are properly connected

to the controller. Check to ensure the drive horsepower is proper for this size of washer. Turn

on power to the washer. (See Note) If problem reappears, contact your Dexter

representative.

12 Washer controller internal error Turn off the power to the washer. Wait one minute. Turn on the power to the washer. (See

Note) If problem reappears, contact your Dexter representative.

13 The control can not communicate with the

drive Turn the power off to the washer. Check the data cable between the controller and the drive.

If no problem is observed, turn on power to the washer and test. (See Note) If problem

reappears, contact your Dexter representative.

14 Over-current on the drive or motor. Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check

the wiring connections to the drive and motor. If no problem is observed, turn on power to the

washer and test. (See Note) If problem reappears, contact your Dexter representative.

Over-voltage on the drive or motor. Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check

the wiring connections to the drive, braking resistors and motor. Measure incoming line

voltage. If no problem is observed, turn on power to the washer and test. (See Note) If

problem reappears, contact your Dexter representative.

Overheating of the drive Turn the power off to the washer. Allow the drive to cool. Check the cooling fins of the drive

to ensure proper airflow. Check the wiring to the drive including the fan wiring. If no problem is

observed, turn on power to the washer and test. (See Note) If problem reappears, contact

your Dexter representative.

17 Overload of the drive or motor Turn the power off to the washer. Check the washer motor to ensure it turns freely. Check

the wiring connections to the drive and motor. If no problem is observed, turn on power to the

washer and test. (See Note) If problem reappears, contact your Dexter representative.

18 Ground Fault to the drive Turn the power off to the washer. Check the wiring connections to the drive and motor. Check

the ground wiring of the drive, motor and incoming connection to ensure a proper ground is

present. If no problem is found, contact your Dexter representative.

19 Low Voltage to the drive Turn the power off to the washer. Check the wiring connections to the drive and motor. If no

problem is observed, turn on power to the washer and test. (See Note) Measure the incoming

line voltage. If problem reappears, contact your Dexter representative.

20 Internal drive error Turn the power off to the washer. Wait one minute. Turn the power on to the washer. (See

Note) If problem reappears, contact your Dexter representative.

21 Data error on communications between the

controller and drive Turn the power off to the washer. Check the data cable between the controller and the drive.

If no problem is observed, turn on power to the washer and test. (See Note) If problem

reappears, contact your Dexter representative.

Note: Whenever power is turned off to the washer, it must remain off for one minute. The washer will not operate properly if this is not done.

ACCESSORIES

INSTALLATION: (Furnished) QTY. 900/950

9990-027-011 Hose, Water Supply 2/4

8641-242-000 Washer, Inlet Hose 2/4

9565-003-001 Strainer, Inlet Hose 4/8

Contact your distributor or Dexter Laundry, Inc. if a steel-mounting base is required.

www.dexterlaundry.com

Dexter Laundry T-950 Express Installation guide

Brand: Dexter Laundry

Model: T-950 Express

Category: Washing machines

Type: Installation guide

Download PDF

report

Dexter Laundry T-950 Express Installation guide

Dexter Laundry T-950 Express Installation guide

Related papers

Other documents